Loren Data's SAM Daily™

FBO DAILY ISSUE OF DECEMBER 14, 2002 FBO #0377
MODIFICATION

66 -- CUSTOM DESIGNED AND BUILT CLASS III GLOVE BOX

Notice Date

12/12/2002
 

Notice Type

Modification
 

Contracting Office

ACA, Dugway Proving Ground, Division of Contracting, Building 5330 Valdez Circle, Dugway, UT 84022-5000
 

ZIP Code

84022-5000
 

Solicitation Number

DABJ19-03-T-0011
 

Response Due

1/6/2003
 

Archive Date

3/7/2003
 

Point of Contact

ERIC VOKT, 435-831-2107
 

E-Mail Address

Email your questions to ACA, Dugway Proving Ground
(vokte@dpg.army.mil)
 

Small Business Set-Aside

N/A
 

Description

NA The U.S. Army Contracting Agency Dugway Proving Ground is soliciting for the design, manufacture, and deliver of a Class III custom built stainless steel glove box and sample box. The government anticipates a firm fixed-price contract. The following are th e specifications for the glove box: 1) the glove box shall be 12 gauge (.109) type 316 stainless steel welded design, reinforced in areas bearing weight loads; 2) dimensions for the glove box shall be 6 ft. wide x 10 feet long x 7 feet high; 3)Nuclear, Bio logical, Chemical (NBC) filtraton shall be included; 4) constructed in three sections to be bolted together inside the containment suite. Radiuses are required in the corners; 5) reinforced floor, kinked to allow for drainage; 6) 15 glove ports with insul ated covers; 7) 1/2-inch lexan viewing windows; 8) 12x12x12 air lock with purge; 9) inlet and outlet HEPA filters with shut off valves; 10) digital pressure gauge and alarm; 11) flourescent lighting; 12) six sealed electrical outlets; 13) motor blower with HEPA and carbon filters (bag-in, bag-out); 14) 1-inch valve (open-close) to hook up decon system to sampling box; 15) the floor of the glove box shall carry 1,500 lbs; and 16) it shall be a negative pressure system. The following are the specifications fo r the sample box: 1) the sample box shall be designed to go inside the glove box as specified above; 2) the dimensions shall be 4.5 ft. wide by 5 ft. long by 6 ft. high; 3) the box shall be constructed in two sections (to fit thru the door); 4) the box sha ll contain a stainless steel lift off access door; 5) the box shall have eight (8) each 1/8-inch to 1/4-inch stainless steel penetrating tubes for sampling ports. The offeror shall also be responsible for the installation and leak detection of the both th e glove box and sample box systems. Drawings of the glove box and sample box are available to potential offerors upon request. The company will be required to supply engineering details for acceptance by the government prior to the issuance of the final engineering details and manufacturing of the glove box. After detail acceptance, the contractor shall manufacture the Class III glove box and sample box per the accepted details and deliver after manufacture, F.O.B. Destination, to the Accountable Property Officer; Building 5464; Dugway, Utah 84022-5000. Delivery for the Class III glove box will be on or before May 2, 2003. Solicitation is DABJ19-03-T-0011 and will be available on or about 12 December 2002 at the Army's Single Face to Industry web site (htt p://acquisition.army.mil) or the U.S. ACA, Dugway Proving Ground web site (https://www.dugway.army.mil/10-3_ContractingDivision.htm). Note FAR Clause 52 .232-18: Availability of Funds (Apr 1984) - Funds are not presently available for this contract. The Go vernment's obligation under this contract is contingent upon the availability of appropriated funds from which payment for contract purposes can be made . No legal liability on the part of the Government for any payment may arise until funds are made avail able to the Contracting Officer for this contract and until the Contractor receives notice of such availability, to be confirmed in writing by the Contra cting Officer. Responses must be submitted not later than 4:00 PM MST, 6 January 2003. In the event th e Army Single Face to Industry web site, http://acquisition.army.mil is not accessible, responses may be faxed at this number (435) 831-2085. The point of contract concerning this solicitation is Mr. Eric S. Vokt, Contract Specialist at (435) 831-2107, or email vokte@dugway.army.mil.
 

Place of Performance

Address: ACA, Dugway Proving Ground Division of Contracting, Building 5330 Valdez Circle Dugway UT

Zip Code: 84022-5000

Country: US
 

Record

SN00222376-W 20021214/021212213653 (fbodaily.com)
 

Source

FedBizOpps.gov Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's FBO Daily Index Page |