SOLICITATION NOTICE
23 -- FY05 Procurement of Truck Mounted Crane
- Notice Date
- 2/15/2005
- Notice Type
- Solicitation Notice
- NAICS
- 441229
— All Other Motor Vehicle Dealers
- Contracting Office
- Department of the Navy, Naval Facilities Engineering Command, Engineering Field Division, Pacific, OICC Sasebo, Sasebo Naval Base, Building 320 Hirase-cho, Sasebo, AP, 857-0056
- ZIP Code
- 00000
- Solicitation Number
- N62836-05-T-6048
- Response Due
- 3/8/2005
- Archive Date
- 3/23/2005
- Description
- This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. The solicitation number N62836-05-T-6048, and is issued as a Request For Quotation (RFQ). The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 25. CONTRACT LINE ITEM 0001, Truck Mounted Crane, Telescoping Boom, H-Type Outrigger, Diesel Engine Drive, 2.9 Metric Ton Capacity Crane; QUANTITY: One; UNIT OF MEASURE: Each. (A) DIMENSION: Manufacturer's standard. (1) Crane Boom Minimum Length: 10.8 Meters (35.43 Feet) (2) Truck Bed Minimum Capacity 3.5 Metric Ton (3) Truck Bed Minimum Length 4.35 Meters (B) CONTRACT REQUIREMENTS: (1) Exterior Color: Manufacturer's standard color. (2) Identification Markings and Registration Numbers: The U.S. Government shall provide License plates for the Contractor to install on the crane front and back. (3) Rust Proofing and Under Coating: Manufacturer's standard. (4) Attachments: Equipment shall have the following Attachments as a minimum. (i) Load Moment Indicator. Manufacturer?s Standard. (ii) Back Up Lights. Shall be installed on the left and right hand rear of the carrier frame. (iii) Operations. Crane shall have 5-lever type control system. (iv) Red and Yellow side lights are required. (v) Tire marker lights are required. (vi) Hooks and nuts must not be plated or painted. Hooks and nuts must be able to pass a government NDT. NDT will be magnetic particle method. Acceptance criterion shall be no linear indications greater than 1.5875 mm?s (1/16 inch). Hooks and nuts shall be delivered to the government for testing prior to government?s factory Quality Assurance and Load Testing. The hook and nut shall not be welded at anytime in the manufacturing process. (vii) Truck bed floor tie down rings must be installed on the left and right side of the floor bed at a minimum of every 60 cm?s. (viii) Truck side panel holes to allow for tie down to the outside tie downs without bending the side panels. Minimum 5 on each side of the truck. (ix) Automatic hook stowage is required. (x) Additional steel box under the bed is required for the stowage of rigging gear and cribbing. (xi) Truck bed work lights (2 each) are required. (5) Hour meter: Manufacturer's standard. (6) Warranty: Manufacturer's standard. The warranty work will be provided by dealers around the Sasebo area, Japan with Government personnel providing Quality Assurance of all work. All warranty work to include the Manufacturer?s warranty term inspections shall be conducted at no cost to the government to include parts and labor. Any warranty work performed to include warranty term inspections and breakdowns shall be documented in detail to include the repair procedure and the parts installed at no extra cost to the government. Detailed report shall be provided within 48 hours after completion of any and all warranty work. (7) Technical Publications: Two (2) sets of operator manuals (Japanese) and Two (2) sets of Operator?s Manuals (English) for each equipment installed on the crane, two (2) sets of Technical (shop repair) manuals and part catalog (Japanese) and two (2) sets of Technical (shop repair) manuals and part catalog (English) for each equipment installed on the crane, to be furnished by Contractor 30 days prior to date of equipment delivery. English manuals are only required if available. (8) Accessories: Shall be the type installed on manufacturer's standard domestic production model. (9) U. S. Government Initial Testing. The Contractor shall provide representatives to observe and provide guidance in the initial testing conducted by the Government at the Government?s Facilities in Sasebo, Japan at no additional cost to the Government. A report of maximum rated over load test (110% +5% -0%) by the manufacturer shall be provided upon delivery. (10) Training. (i) Operator training shall be provided to U. S. Government personnel in Japanese at the Government?s Facilities in Sasebo, Japan at no additional cost to the Government at the time of delivery. Minimum training time is one period of 8 hours. (ii) Maintenance, Inspection and Testing Training shall be provided in Japanese at the Government?s Facilities in Sasebo, Japan at no additional cost to the Government at the time of delivery. Minimum training time is one period of 8 hours. (11) Tools. All special tools required for the maintenance, inspection, operation and testing of the crane shall be provided by the contractor at the time of delivery of the crane. (12) Wire Rope End Connection. The crane shall be delivered with 4 parts of line reeved on the main hoist with either a swage or poured socket end connection. No wedge sockets are permitted. If the main hoist motor line pull is capable, wire rope length should be capable of the hook block reaching the ground with four parts of line and the boom fully extended at minimum radius. A certificate of maximum wire rope length shall be provided upon delivery. (13) Service Bulletins. Contractor shall provide Service Bulletins as issued for the life of the crane. (14) Technical Assistance. The contractor shall provide technical assistance as required for the maintenance of the crane to include engineering procedures for the repair of structural cracks, unusual problems where the normal troubleshooting is not effective, etc. (15) Free Fall Mode. Not acceptable. (16) Wire Rope Breaking Strength Certificate. Manufacturer?s Certificate is required for the Boom Extend, Retract and Main Hoist Wire Rope (as required). (C) INTENDED USE: The equipment covered by this specification is intended for general administrative use by the U. S. Government. The equipment furnished hereunder shall be delivered ready for immediate use. (D) SAFETY. Each piece of equipment installed on the crane shall comply with Japanese Industrial Standard safety requirements. (E) CRANE DELIVERY. The crane shall be fully set up and ready for immediate use upon delivery. The crane may be set up at the government?s facilities at no cost to the government. (F) DELIVERY POINT. All transportation charges borne by the contractor to the Transportation Officer, U. S. Naval Engineering Command Far East, Transportation Department, Sasebo, Japan, (Tel 0956-50-3497 EXT 3497, DSN 252-3497). (G) DELIVERY DATE. The equipment shall be delivered at the delivery point specified above within 120 calendar days after date of contract award. FAR clause 52.212-4, Contract Terms and Conditions-Commercial Items, and clause 52.212-5, Contract Terms and Conditions Required To Implement Statutes or Executive Orders-Commercial Items, applies to this acquisition and are incorporated by reference. Offerors shall include a completed copy of the provision at 52.212-3, Offeror Representations and Certifications-Commercial Items, with its offer. FAR provision 52.212-1, Instructions to Offerors ? Commercial Items, applies to this acquisition and is incorporated by reference. FAR provision 52.212-2, Evaluation ? Commercial Items, apply to this acquisition and is incorporated by full text, as follows: 52.212-2 Evaluation-Commercial Items (Jan 1999) (a) The Government will award a contract resulting from this solicitation to the responsible offeror whose offer conforming to the solicitation will be most advantageous to the Government, price and other factors considered. The following factors shall be used to evaluate offers: (1) technical capability of the item offered to meet the Government requirement; (2) price; and (3) past performance (see FAR 15.304). (b) A written notice of award or acceptance of an offer, mailed or otherwise furnished to the successful offeror within the time for acceptance specified in the offer, shall result in a binding contract without further action by either party. Before the offer's specified expiration time, the Government may accept an offer (or part of an offer), whether or not there are negotiations after its receipt, unless a written notice of withdrawal is received before award. All quotes shall be in the English language and priced in Japanese Yen only. All quotes shall include (1) Price Quotation: One (1) set, (2) Completed Representations and Certifications: One (1) set, (3) Technical Proposal: One (1) set, and Past Performance information: One (1) set. TECHNICAL PROPOSAL REQUIREMENT: (1) Catalogues or other product literature identifying the features and specifications of each crane offered. At a minimum, the literature should identify compliance with the specifications: One (1) set. (2) The Contractor shall identify in his proposal as to which specified items his proposed crane meets. The contractor may use the specification by putting a ?YES? or ?NO? in red ink pen at the end of each specified item, and submitting it with the proposal. Any deviations from the Government?s proposed specification shall also be identified in red ink pen and submitted with a deviation summary: One (1) set. All quotes are due on 8 March 2005 at 1100 hours. All quotes shall be submitted to: Naval Facilities Engineering Command, Far East, Resident Officer in Charge of Construction, Sasebo, PSC 476 BOX 66, FPO AP 96322-1160. Any questions may be submitted to Mr. Hirokazu Toyofuku, Contract Specialist, at Telephone: 011-81-956-50-2395, Fax: 011-81-956-23-2535, or E-mail address: hirokazu.toyofuku@sasebo.navy.mil.
- Place of Performance
- Address: PSC 476 BOX 66 FPO AP 96322-1160
- Country: Japan
- Country: Japan
- Record
- SN00751517-W 20050217/050215212305 (fbodaily.com)
- Source
-
FedBizOpps.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |