PRESOL | 59 | Amplifiers, 1 Kw 100 MHz to 1000 MHz Amplifier (1 each); 200 Watt 100 MHz to 1000 MHz Amplifier (1 each); 1 Kw 100 kHz to 220 MHz Amplifier (1 each)

FBO DAILY ISSUE OF JUNE 12, 2005 FBO #1294
SOLICITATION NOTICE

59 -- Amplifiers, 1 Kw 100 MHz to 1000 MHz Amplifier (1 each); 200 Watt 100 MHz to 1000 MHz Amplifier (1 each); 1 Kw 100 kHz to 220 MHz Amplifier (1 each)

Notice Date: 6/10/2005
Notice Type: Solicitation Notice
NAICS: 334419 — Other Electronic Component Manufacturing
Contracting Office: RDECOM Acquisition Center - Adelphi, ATTN: AMSSB-ACA, 2800 Powder Mill Road, Adelphi, MD 20783-1197
ZIP Code: 20783-1197
Solicitation Number: W911QX-05-T-0134
Response Due: 6/22/2005
Archive Date: 8/21/2005
Small Business Set-Aside: Total Small Business
Description: (i) This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued. (ii) The solicitation number is W911QX-05-T-0134. This acquisition is issued as a request for quotation (RFQ) (iii) The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 01-27. (iv) This acquisition is 100% set-aside for small business concerns. The associated NAICS code is 334419. The small business size standard is 500 employees. (v) The following is a list of contract line item number(s) and items, quantities and units of measure: Line Item 0001, 1 Kw 100 MHz to 1000 MHz Amplifier (1 each) Line Item 0002, 200 Watt 100 MHz to 1000 MHz Amplifier (1 each) Line Item 0003, 1 Kw 100 kHz to 220 MHz Amplifier (1 each) (vi) Description of requirements: Line Item 0001, 1 Kw 100 MHz to 1000 MHz Amplifier (1 each) Amplifier type: Solid state Frequency range: 100 MHz to 1 GHz without any operator intervention, e.g. throwing a switch or moving a cable. (prefer this freq range be from 20 MHz to 1 GHz) Power output@ 1dB compression point: 1000W CW minimum (across the band) Power flatness: +/- 2.5 dB (as measured at 1dB compression), (prefer +/- 1 dB) Automatic level control: yes Mismatch tolerance: 100% of rated power without foldback up to a 6:1 mismatch. Will operate without damage or oscillation with any VSWR of 6:1 or greater Spurious outputs: -50dBc maximum Harmonic distortion: -20 dBc maximum at 1 dB compression point Noise Figure: 31 dB maximum Gain at rated power: 63dB maximum Gain flatness: +/- 2dB maximum Gain stability: 0.1dB during any 10 minute period RF Output impedance: 50 ohms, RF Output connector type: Female, type 7/16 or 1 5/8 RF Output mounting: Rear panel Output monitor: 63dB, nominal Output monitor connector: Female, N type RF Input impedance: 50 ohms, VSWR 2.0:1 RF Input connector: Female, N type RF Input protection: protected against damage from overdrive up to 20dBm. RF Input mounting: Front panel Amplifier to be protected against: Thermal Overload, Over current, Over voltage, High VSWR Front panel mounted meaningful fault indicators Front panel mounted gauge/display indicating value of output power, VSWR or forward & reverse pwr, temperature, Safety Interlock: 15 pin female subminiature D on rear panel Remote control: via IEEE-488 and have access to all amplifier control functions & status indicators on rear panel Electrical Power Requirements: Primary power: 3 phase, 208 VAC 60Hz NEMA 18-60R electrical plug 8 electrical cord Mechanical: Rack mounted: yes Wheels: yes Lift rings: four on top, one at each corner. Maximum Weight: 2000 lbs Maximum dimensions: 80H x 63W x 63D excluding wheels and lift rings. Environmental: Cooling Forced air-cooled (self contained fans) to permit continuous full power operation. Operating Temperature: 0 - 45 degrees Centigrade. Operating Altitude: 0 to 6 thousand feet. Documentation: full set of documentation (e.g. user manual & programming reference guide) and production test data demonstrating amplifier performance from 100 MHz to 1 GHz for power delivery at 1dB compression point, VSWR, harmonic performance, and spurio us signals Warranty: 3 year, 100% warranty on parts and labor Line Item 0002, 200 Watt 100 MHz to 1000 MHz Amplifier (1 each) Amplifier type: Solid state Frequency range: 100 MHz to 1 GHz without any operator intervention, e.g. throwing a switch or move a cable. Power output@ 1dB compression point: 200W CW minimum (across the band) Power flatness: +/- 2 dB (as measured at 1dB compression), (prefer +/- 1 dB) Automatic lev el control: yes Mismatch tolerance: 100% of rated power without foldback. Will operate without damage or oscillation with any VSWR of 6:1 or greater Spurious outputs: -50dBc maximum Harmonic distortion: -20 dBc maximum at 200 watts Noise Figure: 30 dB maximum Gain at rated power: 53dB minimum Gain flatness: +/- 2dB maximum Gain stability: 0.1dB during any 10 minute period RF Output impedance: 50 ohms, RF Output connector type: Female, type N RF Output mounting: Rear panel RF Input impedance: 50 ohms, VSWR 2.0:1 RF Input connector: Female, N type RF Input protection: protected against damage from overdrive up to 10dBm. RF Input mounting: Front panel Amplifier to be protected against: High VSWR & thermal overload Front panel mounted meaningful fault indicators Front panel mounted gauge/display indicating value of output power, VSWR or forward & reverse power, temperature Remote control via IEEE-488 and have access to all amplifier control functions & status indicators Electrical Power Requirements: Primary power: 120 VAC 60Hz 6 electrical cord Mechanical: Rack mount kit: yes Maximum Weight: 250 lbs Maximum dimensions: 19 W x 24 D x 24 H Environmental: Cooling Forced air-cooled (self contained fans) to permit continuous full power operation. Operating Temperature: 0 - 45 degrees Centigrade. Operating Altitude: 0 to 6 thousand feet. Documentation: full set of documentation (e.g. user manual & programming reference guide) and production test data demonstrating amplifier performance from 100 MHz to 1 GHz for power delivery, VSWR, harmonic performance, and spurious signals Warranty: 3 year, 100% warranty on parts and labor Other: All connectors on rear panel Line Item 0003, 1 Kw 100 kHz to 220 MHz Amplifier (1 each) Amplifier type: Solid state Frequency range: 100 kHz to 220 MHz without any operator intervention, e.g. throwing a switch or moving a cable. Power output@ 1dB compression point: 1000W CW minimum (across the band) Power flatness: +/- 3.5 dB (as measured at 1dB compression), (prefer +/- 1 dB) Automatic level control yes RF Rise/Fall Time 20 nanoseconds maximum Mismatch tolerance: 500 watts of rated power without foldback up to a 6:1 mismatch. Will operate without damage or oscillation with any VSWR of 6:1 or greater Spurious outputs: -50dBc maximum Harmonic distortion: -20 dBc maximum at 1 dB compression point Noise Figure: 31 dB maximum Gain at rated power: 63dB maximum Gain stability: 0.1dB during any 10 minute period RF Output impedance 50 ohms, VSWR 2.5:1 maximum RF Output connector type: Female, type 7/16 RF Output mounting: Rear panel Output monitor: 63dB, nominal Output monitor connector: Female, N type RF Input impedance: 50 ohms, VSWR 2.0:1 RF Input connector Female, N type RF Input protection protected against damage from overdrive up to 20dBm. RF Input mounting: Front panel Amplifier to be protected against: Thermal Overload, Over current, Over voltage, High VSWR Front panel mounted meaningful fault indicators Front panel mounted gauge/display indicating value of output power, VSWR or forward & reverse power temperature Safety Interlock 15 pin female subminiature D on rear panel Remote control via IEEE-488 and have access to all amplifier control functions & status indicators on rear panel Electrical Power Requirements: Primary power: 3 phase, 208 VAC 60Hz NEMA 18-60R electrical plug 8 electrical cord Mechanical: Rack mounted yes Wheels yes Lift rings four on top, one at each corner. Maximum Weight 1000 lbs Maximum dimensions: 60H x 30W x 36D excluding wheels and lift rings. Environmental: Cooling Forced air-cooled (self contained fans) to permit continuous full power operation. Operating Temperature 0 - 45 degrees Centigrade. Operating Altitude 0 to 6 thousand feet. Documentation full set of documentation (e.g. user manual & programming r eference guide) and production test data demonstrating amplifier performance from 100 kHz to 220 MHz for power delivery at 1dB compression point, VSWR, harmonic performance, and spurious signals Warranty: 3 year, 100% RF electronics, power supply and support electronics (vi) Delivery is required by six months from award. Delivery shall be made to White Sands Missile Range, NM. Acceptance shall be performed at White Sands Missile Range, NM. The FOB point is White Sands Missile Range, NM (destination). (vii) The following provisions and FAR/DFAR clauses can be obtained at http://www.arl.army.mil/contracts/opport.htm, http://farsite.hill.af.mil/VFFAR1.htm, or http://farsite.hill.af.mil/VFDFARa.htm (viii) The provision at 52.212-1, Instructions to Offerors - Commercial, applies to this acquisition. (ix) The provision at FAR 52.212-2, Evaluation - Commercial Items is applicable to this acquisition. The specific evaluation criteria to be included in paragraph (a) of that provision are as follows: (a) The Government will award up to three (3) contracts resulting from this solicitation to the responsible offeror(s) whose offer conforming to the solicitation will be most advantageous to the Government, price and other factors considered. The following factors shall be used to evaluate offers: (i) The technical capability of the item(s) offered to meet the Government requirement as described above. Offers will be evaluated to determine if the product(s) offered meet or exceed each of the minimum specifications identified above. Each line item will be evaluated separately. Offers shall include sufficient technical documentation regarding the specifications of the offered product(s) for the Government to determine if all the minimum requirements stated above are met or exceeded. Offerors may su bmit a quote for one, two or all three line items. Offers shall specifically identify which contract line item (0001, 0002 or 0003) any product offered is in response to. (ii) Price. The Government intends to award a contract, or contracts, for the lowest-priced items meeting all the stated minimum requirements. Price will be the critical factor in determining which technically acceptable offer will be the awardee. Con versely, for any product offered that does not meet the stated minimum specifications, price is irrelevant. (iii) Past performance. Offers shall include evidence of identical or very similar items having been sold in the past. Technical and past performance, when combined, are significantly more important than price. If an offer includes a product that does not meet each of the stated minimum specifications, that offer will not be further evaluated or considered for award for t hat line item. For each line item; among offers that meet all of the minimum technical requirements; award will be made to that offeror with the lowest proposed fixed price. If an offer does not include a quote for one or two of the line items, it will s till be considered for the line item(s) quoted. If an offer is determined to be not technically acceptable (i.e., not meeting all the stated minimum specifications) for one or two line items, it will still be considered for the line item(s) that were dete rmined to be technically acceptable. (x) Offerors shall include a completed copy of the provision at FAR 52.212-3, Offeror Representations and Certifications - Commercial Items, and DFARS 252.212-7000, Offeror Representations and Certifications -Commercial Items, with its offer. (xi) The clause at 52.212-4, Contract Terms and Conditions - Commercial Items, applies to this acquisition. (xii) The clause at 52.212-5, Contract Terms and Conditions Required to Implement Statutes or Executive Orders - Commercial Items and DFARS 252.212-7001, Contract Terms and Conditions Required to Implement Statutes or Executive Orders Applicable to Defe nse Acquisitions of Commercial Items, applies to this acquisition. The following additional FAR/DFARS clauses cited in this clause are applicable: 52.203-3, 52.222-3, 52.222-19, 52.222-21, 52.222-26, 52.222-35, 52.222-36, 52.222-37, 52.225-13, 52.232-33, 252.225-7001, 252.247-7023. (xiii) The following additional contract requirement(s) or terms and conditions apply: 52.004-4408, 52.005-4401, 52.032-4418, 52.045-4400. (xiv) The following notes apply to this announcement: Note 1 (xv) Offers are due on 06/22/2005, by 11:59PM, by email to jmcveigh@arl.army.mil. (xvi) For information regarding this solicitation, please contact Gerard K. McVeigh, 301-394-1615, jmcveigh@arl.army.mil.
Place of Performance: Address: RDECOM Acquisition Center - Adelphi ATTN: AMSSB-ACA, 2800 Powder Mill Road Adelphi MD; Zip Code: 20783-1197; Country: US
Record: SN00827580-W 20050612/050612190626 (fbodaily.com)
Source: FedBizOpps.gov Link to This Notice
(may not be valid after Archive Date)

| FSG Index | This Issue's Index | Today's FBO Daily Index Page |

Loren Data's SAM Daily™

59 -- Amplifiers, 1 Kw 100 MHz to 1000 MHz Amplifier (1 each); 200 Watt 100 MHz to 1000 MHz Amplifier (1 each); 1 Kw 100 kHz to 220 MHz Amplifier (1 each)