SOLICITATION NOTICE
73 -- RFQ for FORK, TABLE (STAINLESS STEEL)
- Notice Date
- 4/12/2006
- Notice Type
- Solicitation Notice
- NAICS
- 332214
— Kitchen Utensil, Pot, and Pan Manufacturing
- Contracting Office
- General Services Administration, Federal Supply Service (FSS), Southwest Supply Center (7FL), 819 Taylor Street RM 6A06, Fort Worth, TX, 76102
- ZIP Code
- 76102
- Solicitation Number
- 7FLA-S6-06-8169-OMP
- Response Due
- 4/24/2006
- Archive Date
- 12/31/2006
- Description
- 7340-00-241-8169 FORK, TABLE (STAINLESS STEEL): Shall have the following characteristics: Graded, Fork, Utility, table Unit of Issue ? BX (box of 24) SALIENT CHARACTERISTICS. MATERIAL. The flatware shall be fabricated from stainless steel in accordance with types 301, 302, or 304 of ASTM A 240/A 240M or ASTM A 666 (except for bend test requirements), or type 430 of ASTM A 276. DESIGN AND CONSTRUCTION. The flatware shall be the ?Windsor? pattern and shall be graded construction. The flatware shall be of single piece construction of the stainless steel specified under ?Material? and shall conform to the requirements specified herein. NOTICE: Packaging and packing requirements in this item purchase description are unique at the request of the U.S. Navy Supply Systems Command. This item is included in the Navy?s PLASTICS REMOVAL IN MARINE ENVIRONMENT (PRIME) PROGRAM under the U.S. Marine Plastic Pollution Research and Control Act of 1987 (MPPRCA) and the International Convention for the Prevention of Pollution from Ships Treaty (MARPOL) Annex V. Items in the PRIME program require biodegradable packing materials. The statement ?PLASTIC PACKING MATERIALS AND PRESSURE SENSITIVE TAPES ARE PROHIBITED? is included in the packaging and packing requirements for all PRIME program items. FORKS. Forks shall be of the shape shown on the figure below and shall conform to dimensions specified below. The shanks and tines shall have an average Rockwell hardness not less than B85 when tested in accordance with ASTM E18. All edges All edges shall be rounded and smooth and the back of the handle shall be concave in accordance with the manufacturer's standard practice. The width and thickness of tines shall taper and shall be pointed at the ends. Inside edges of tines shall be finished so as to keep top and bottom inside edges well rounded. DIMENSIONS. Dimensions (inches) Minimum Maximum Overall length, LT 6-15/16 7-1/8 Width at AA (1/8? from tip of tine) 0.700 0.775 Thickness at AA (1/8? from tip of tine) 0.060 0.080 Width at BB (1/8? from base of tine) 0.900 0.950 Thickness at BB (1/8? from base of tine) 0.072 0.095 Width at CC (at narrowest section) 0.190 0.260 Thickness at CC (at narrowest section) 0.072 0.135 Maximum width of handle, DD 0.735 0.860 Thickness at widest point of handle, DD 0.060 0.095 Tine length, TL 1-3/4 1-15/16 Image is intended to be used as a guide Product may vary FINISH. After fabrication, flatware shall be free of all rough and protruding edges. The spoons shall be given a No. 7 commercial finish or a bright or mirror finish on all surfaces except exterior edges. Flatware shall be free of discoloration and stains. MARKING. The manufacturer?s name, trade name or trademark of such known character easily identifiable with said manufacturer shall be applied. The marking shall be indented or embossed on the handle or blade of the knives adjacent to the blade or handle in accordance with the manufacturer?s standard practice. The surface opposite the markings shall show no signs of penetration. WORKMANSHIP. The finished flatware shall be clean and smooth and shall not contain any burrs, rough die, tool, gouge, or grind marks or burn marks. The finished items shall not be fractured, dented, bent, punctured, or malformed. There shall be no defects which may impair serviceability, durability or appearance. TESTS. Hardness tests. Flatware items shall be prepared and tested for hardness in accordance with ASTM E 18. One reading on each style fork midway between AA and BB; one reading between BB and CC; and one reading within 3/8 inch of CC on the handle as shown on figure shall be taken to determine conformance. Any average hardness reading not falling within the specified hardness limits will be cause for rejection of the lot being tested. CLASSIFICATION OF DEFECTS. Finish Flatware not equal to a commercial No. 7 finish or a mirror, or bright finish except tines and all exterior edges. Fork tines not smooth. Evidence of discoloration, or stains. Construction Any burrs, slivers, sharp edges, rough die marks, or tool gouge. And All outer edges, not rounded and smooth. Workmanship Any fork fractured, dented, or malformed. Not single piece construction. Inside of tines not finished as spec. Edge of tines not rounded. Tines not tapered. handle not concave. Marking Missing, incomplete or illegible. Surface opposite marking is penetrated. Surface opposite marking is uneven. PRODUCT CONFORMANCE. The products provided shall meet the salient characteristics of this description, conform to the producer's own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. MARKING. Shipments to GSA and other civilian agencies shall be marked in accordance with FED-STD-123. Shipments to the Department of Defense (DoD) shall be marked in accordance with MIL-STD-129. PREPARATION FOR DELIVERY. The item(s) shall be packaged and packed in accordance with the latest revision of ASTM D 3951, Standard Practice for Commercial Packaging. Copies of ASTM standards are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Phone: 610-832-9585, Fax: 610-832-9555, Web site: www.astm.org, e-mail: service@astm.org. Palletization: The shipping (transport) containers shall be palletized. The pallets shall be 48-inch length x 40-inch width, general purpose, four-way entry, flush stringer, and double-face non-reversible pallets. The palletized load shall not exceed 2500 pounds in weight for shipments to the Eastern Distribution Center (Burlington). The palletized load shall not exceed 2000 pounds in weight for shipments to the Western Distribution Center (French Camp and Stockton locations). The palletized load shall not overhang the pallet deck board edge by more than 1 inch and shall not exceed 53 inches in overall height (including pallet). Less than half pallet loads or loads shipped by small package carrier in acceptable transport packing need not be palletized. When less than full but more than a half pallet is used, the palletized load shall utilize proper bracing and/or reinforcement to ensure that the load can withstand two additional loads placed on it. Stacking. A load-stacking test shall be performed once, at the beginning of the contract, for each different unitized or palletized load configuration. A fully palletized load shall be tested utilizing a total stack of three palletized loads, with all the proper bracing and/or reinforcement necessary to perform the test. There shall be no evidence of damage to the pallets, shipping containers or products when stack is tested on the rigid surface for a minimum of 24 hours, in compliance with all the National and Local Safety Regulations. The pre-tested palletized load configuration shall be duplicated using the same packaging materials, pattern, number of shipping (transport) containers, and procedures consistent throughout the duration of the contract. Palletized loads shall be stable and safe when handled with mechanical equipment by qualified personnel. Materials. All lumber used inside or outside a shipment shall be bark free. No used wood pallets with repaired components or stringers will be acceptable. All wood pallet stringers shall be manufactured from hardwoods. Pallets manufactured of materials other than wood, shall conform to all the requirements specified herein. Unitization. For the purpose of this requirement, the assembled group of containers or items in a single load that can be handled as a unit throughout the distribution system. Unitization encompasses, but is not limited to, consolidation in a container, placement on a pallet or load base having forklift capability, or securely binding together. Shipments should be considered for unitization where appropriate or specified. Unitization of pallet load. The palletized load shall be unitized and secured to the pallet to insure that the load arrives intact without product damage. The containers or items shall be placed in a suitable pattern to form a stable and balanced load. Vertical, horizontal or filler reinforcement shall be added as necessary to meet the stacking strength requirements. A palletized load shall be secured to the pallet by shrink or stretch wrapping, and/or, by steel or nonmetallic strapping. When steel or nonmetallic strapping is used, edge protectors shall be provided to prevent damage to the cartons when tensioning the strapping. As a minimum, two straps shall run lengthwise, two straps shall run widthwise, and two straps shall run around the girth of the palletized load. A palletized load shall be capable of protecting the products against damage in a multiple handling, transportation, and storage environment having distribution warehouses with rack systems that support the load/s overhead of warehouse personnel. Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, ?Guidelines for Regulating Wood Packaging Material in International Trade?. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17. (2/6/06)
- Record
- SN01026951-W 20060414/060412222119 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |