Loren Data's SAM Daily™

FBO DAILY ISSUE OF JUNE 16, 2006 FBO #1663
SOLICITATION NOTICE

56 -- This is for the replacement of the fence located at the U. S. Coast Guard Shoreside Detachment Demopolis, Alabama.

Notice Date

6/14/2006
 

Notice Type

Solicitation Notice
 

NAICS

237990 — Other Heavy and Civil Engineering Construction
 

Contracting Office

Department of Homeland Security, United States Coast Guard (USCG), USCG Sector Mobile, South Broad Street, Building 101, Mobile, AL, 36615-1390
 

ZIP Code

36615-1390
 

Solicitation Number

HSCG82-06-Q-3WDLA0
 

Response Due

6/30/2006
 

Archive Date

7/30/2006
 

Description

Scope of Work: a. Installation of 8? classic stockade-style privacy fence Fence Description: (187? Dog-eared fence) Fence materials shall be: Grade 1, 1?x 6? x 8? cedar dog eared fence boards. Grade 2 or better 2 X 4 treated pine for rails Grade 2 or better 4? x 4? x 10? treated pine fence posts Grade 2 or better 6? x 6? x 10? treated pine fence corner posts #8 x 1-1/4? galvanized or stainless deck screws for attaching boards to rails #10 x 3? galvanized or stainless deck screws for attaching rails to posts Gravel Concrete 1. Contractor is to dig a 3 foot deep by 10 inch hole for 4 x 4?s, or 12 inch diameter holes for 6 x 6 corners. The hole should be slightly bigger at the bottom for better anchoring. Place two shovels full of gravel at the bottom of each hole. 2. Set posts in ground with 7 feet of the post exposed, and fill holes with concrete mix, and level pole. When the pole is firmly in position, build a mound around it to help eliminate water standing at the post base. 3. Slope the concrete slightly away from the post and round it off with a trowel. Tamp the concrete lightly to eliminate any air bubbles left in the mixture that can act as water pockets. Brace posts as necessary to maintain level and allow concrete to harden a minimum of 48 hours. 4. Posts are to be spaced no more than 8 feet apart. Set the 6 x 6 corner or end posts first. Then stretch a line from each corner or end post to align all 4 x 4 line posts in between. Tops of all posts shall be cut at a 45 degree angle to prevent water from standing and sealed with an EPA approved wood preservative. 5. Attach a top, middle, and bottom 2 X 4 rail to posts with appropriate fasteners. Posts are to be notched horizontally on the sides at least ? inches to accommodate / support the rails. The rails are to be toe nailed with screws into position. 6. The top rail shall be positioned at the bottom of the angle cut on the top of the post. The bottom rail shall be positioned 1 foot above the ground, and the middle rail centered between the top and bottom rails. No rail joints will be accepted between posts. Notches in corner posts are to be cut only big enough to fit the 2 x 4 rail and not cut through the entire width of the 6 x 6 post. 7. Attach fence boards to rails using galvanized or stainless steel deck screws. NO NAILS. Boards are to be spaced on the rail approximately every 3/8 inch. Tops of boards will be leveled and uniform the entire length of fence. In addition, the bottom of the fence board is to be positioned 2 inches above ground. b. Installation of chain link fence Fence Description: (8? Galvanized fence chain fence) Fence materials shall be: The chain fabric shall be 8 foot and 11 gauge or better. Posts: 15 gauge or better. 1. Contractor is to remove and dispose of existing fence and install a new 8 foot galvanized fence leading from the above wood fence down to the waters edge (Approx. 140 feet). This is a straight fence running down hill to the water. 2. Contractor shall remove and dispose of all debris from both jobs. Contact Information: Each prospective contractor must make a site visit to Coast Guard Base Mobile prior to submitting his or her price quotation. The point of contact at SSD Demopolis is BMC Steve Urban or BMCM Charles Unkrich. You may set up an appointment with him by phone: (334) 289-0354 or (334) 289-5268.
 

Place of Performance

Address: Officer-In-Charge, U.S. Coast Guard SSD Demopolis, 1900 Coast Guard Drive, Demopolis, AL

Zip Code: 36732-9999

Country: USA
 

Record

SN01069326-W 20060616/060614220528 (fbodaily.com)
 

Source

FedBizOpps Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's FBO Daily Index Page |