SOLICITATION NOTICE
25 -- Cargo Body Enclosure for standard full size truck bed with cab-over
- Notice Date
- 7/6/2006
- Notice Type
- Solicitation Notice
- Contracting Office
- N00244 Naval Base 937 North Harbor Drive San Diego, CA
- ZIP Code
- 00000
- Solicitation Number
- N0024406T0592
- Response Due
- 7/14/2006
- Archive Date
- 8/13/2006
- Description
- This is a COMBINED SYNOPSIS/SOLICITATION for commercial items prepared in accordance with the information in FAR Subpart 12.6, using simplified acquisition procedures under the test program for commercial items found at FAR 13.5, as supplemented with the additional information included in this notice. This acquisition will be solicited as a small business set aside for 4 EA Cargo body enclosures. The Equipment will be used for to support the transportation and operation of Threat Radar Emitter simulator and PADDS/MADSS systems. This announcement constitutes the only solicitation; a written solicitation will not be issued. PAPER COPIES OF THIS SOLICITATION WILL NOT BE AVAILABLE. This combined synopsis/solicitation shall be posted on both FEDBIZOPPS and NECO (http://www.neco.navy.mil/). The RFQ number is N00244-06-T-0592. This solicitation documents and incorporates provisions and clauses in effect through FAC 2005-09 and DFARS Change Notice 20060616. It is the contractor?s responsibility to be familiar with the applicable clauses and provisions. The clauses may be accessed in full text at these addresses: www.acqnet.gov/far and http://www.acq.osd.mil/dpap/dfars/index.htm. The NAICS code is 336211 and the Small Business Standard in number of employees is 1000. The Fleet and Industrial Supply Center, San Diego, Detachment Seal Beach requests responses from qualified sources capable of providing: ITEM 0001 QUANTITY UNIT UNIT PRICE AMOUNT 2 EA Slip-in Cargo Body Enclosure Unit for standard full size 4 WD truck bed with cab-over 8? bed length by 72-74 inches tall (12?overall length including cab-over) ITEM 0002 2 EA Slip-in Cargo Body Enclosure Unit for standard full size 4WD truck bed with cab-over: 8?bed length by 72-74 inches Tall (12?overall length including cab-over) ITEM 0003 4 EA Standard COTS Manuals: Operation and Maintenance Instructions. Items to be provided in accordance with the following specifications and requirements: 0001-Slip-In Cargo body enclosure unit 1.0 Requirements 1.1. A one-piece mono-body capsule that has full floor support capable of holding the contents even when it is removed from a vehicle 1.2 Pre-configured and factory ready for immediate work service. 1.3 The "Cargobody" has an onboard built-in four point lockdown system that facilitates the quick engagement (2 Min.) to any host vehicle. This "Quick Lock System" enables full vehicle installation without the requirement of any vehicle modification such drilling holes or use of bolts and other hardware. 1.4. On board built-in jack receptacles (4) for optional slip-in jack stands for vehicle transfer or stationary use of Cargobody 1.5 Set of four jack stands, heavy duty capacity 1.6 Interior dome lights (minimum of 6 running down center of roof) 1.7 Dual locking rear cargo doors (w/ tinted windows - one per door) w/automotive slam shut latches 1.8 Double walled industrial fiberglass flooring (skid resistant matting) 1.9 One driver side workbench/cabinet setup (84? long x 20? wide with: 1.9.1 Cabinet, below work surface, multi-drawer configuration 1.9.2 Shelf unit, roof mounted (above desk) w/ multiple sliding doors 1.9.3 Work surface lighting, full length (located below roof cabinets) 1.10 Six full-size interior shelving units (60? long x 12? deep) ? capable of adjustable spacing with dividers for standard type bin boxes and most toolboxes. (NOTE: These are typically heavy duty 18-gauge steel units with rust resistant galvanized coating and lined with non-slip rubber mats). Mount units at the rear of unit on the passenger side. 1.11 One front cable access panel (12? x 12?) 1.12 One rear access panel for inverter wiring 1.13 One rear step (receiver type) 1.14 One roof vent / emergency escape hatch, approximately 24? x 24? 1.15 One roof-mounted HVAC unit, minimum 9,200 BTU cooling and 5,600 BTU heating One carbon monoxide detector 1.16 One smoke detector 1.17 Paint to match color flat tan, Carlsbad Canyon? (Federal Standard 595B, color #30277) or ?Desert Tan? (Federal Standard 595B, color #33446 Main Body Structure: The body is constructed of fiberglass with a glass to resin ratio of 30:70 or ratio. The body is approximately .220" thick constructed using fiberglass mat lamination. All core material sandwiched between two layers of glass and resin. Resin type, neat. (No fillers) Outside finish with an automotive paint. Inside finish white gel-coat with an automotive finish for added interior brightness. Dimensions: Interior Inches Exterior Inches Beam Width: 76" 76 3/4" Overall Length: 107" 108 ? Overall Height: 58" 62" Floor Space (max usable) 99" long 48 1/2" wide Base Empty Weight: 450 lbs. Rear Door Opening height 49 1/2" width 49 1/2" Side Door Opening height 20" width 70" Compartments & Shelving height 2" length 72" depth 12" Standard shelves 3 per assembly (Height spacing adjustable preset at 12") Standard Hardware & Components: High quality corrosion resistant hardware & components: Rear access swing shut doors: Material / Construction Dual rear cargo doors double walled Laminated Fiberglass (no fillers) Reinforced with a minimum of 40% glass content Outer access door paddle handle. Stainless Steel Handle security. Key lock w/interior engagement Inner access door paddle handle Stainless Steel Rear door hinges (size 3" tall) Stainless Steel Rear door stoppers (plunger type)Stainless Steel Door latch operation adjustable Stainless Rods Door seals Bulb type (Automotive) Electrical: Seven pole power junction box, High impact plastic Power access cables 14 Gauge. 4 wire 12V Auxiliary power (interior) All weather receptacle High mounted third brake light; Recessed LED high impact plastic Interior dome lights (6); Marine switch at rear door Flooring: Double walled floor 1 1/4" thick; Multi core ply fiberglass floor Interior rubber floor covering; Skid resistant grooved rubber Compartments & Shelving: Laser cut (non bur) shelving; Galvanized heavy gauge steel Laser cut shelving dividers each 4"; Galvanized heavy gauge steel Shelving liners Skid resistant grooved rubber 0002-Slip-in Cargo Body Enclosure 1.0. Requirements 1.1. A one-piece mono-body capsule that has full floor support capable of holding the contents even when it is removed from a vehicle 1.2. Pre-configured and factory ready for immediate work service 1.3. The "Cargobody" has an onboard built-in four point lockdown system that facilitates the quick engagement (2 Min.) to any host vehicle. This "Quick Lock System" enables full vehicle installation without the requirement of any vehicle modification such drilling holes or use of bolts and other hardware. 1.4. On board built-in jack receptacles (4) for optional slip-in jack stands for vehicle transfer or stationary use of Cargobody 1.5 Set of four jack stands, heavy duty capacity 1.6 Interior dome lights, (minimum of six running down the center of roof) 1.7 Dual locking rear cargo doors (w/ tinted windows - one per door) w/automotive slam shut latches 1.8 Double-walled industrial flooring, smooth tile (need to be able to slide heavy equipment in and out) 1.9 One front cable access panel, 12? x 12? 1.10 One rear step, receiver type 1.11 One side access door w/key lock double walled door 20? tall x 70? long (upward swing with support arms/gas shocks) 1.12 One roof vent / emergency escape hatch, approximately 24? x 24? 1.13 One roof-mounted HVAC unit, minimum 9,200 BTU cooling and 5,600 BTU heating 1.14 One carbon monoxide detector 1.15 One smoke detector 1.16 Paint to match color flat tan, ?Carlsbad Canyon? (Federal Standard 595B, Color #30277) or ?desert Tan? (Federal Standard 595B, color #33446) Main Body Structure: The body is constructed of fiberglass with a glass to resin ratio of 30:70 or ratio. The body is approximately .220" thick constructed using fiberglass mat lamination. All core material sandwiched between two layers of glass and resin. Resin type, neat. (No fillers) Outside finish with an automotive paint. Inside finish white gel-coat with an automotive finish for added interior brightness. Dimensions: Interior Inches Exterior Inches Beam Width: 76? 76 ?? Overall Length: 107? 108 1/4? Overall Height: 58? 62? Floor Space (max usable) 99? long 48 ?? wide Base Empty Weight: 450 lbs. Rear Door Opening height 49 ?? width 49 ?? Side Door Opening height 20? width 70? Compartments & Shelving height 2? length 72? depth 12? Standard shelves ? 3 per assembly (Height spacing adjustable preset at 12?) Standard Hardware & Components: High quality corrosion resistant hardware & components: Rear access swing shut doors: Material /Construction Dual rear cargo doors double walled/ Laminated Fiberglass (no fillers) Reinforced with a minimum of 40% glass content Outer access door paddle handle in Stainless Steel Handle security: Key lock w/interior engagement Inner access door paddle handle is Stainless Steel Rear door hinges (size 3" tall) Stainless Steel Rear door stoppers (plunger type) Stainless Steel Door latch operation adjustable Stainless Rods Door seals Bulb type (Automotive) Electrical: Seven pole power junction box high impact plastic Power access cables 14 Gauge. 4 wire 12V Auxiliary power (interior)all weather receptacle High mounted third brake light Recessed LED high impact plastic Interior dome lights (6) Marine switch at rear door Flooring: Double walled floor 1 1/4" thick. Multi core ply fiberglass floor Interior rubber floor covering Skid resistant grooved rubber Compartments & Shelving: Laser cut (non bur) shelving Galvanized heavy gauge steel Laser cut shelving dividers each 4" Galvanized heavy gauge steel Shelving liners Skid resistant grooved rubber FOB Destination. Place of delivery is Fallon, NV. 89406. The following FAR provisions and clauses are applicable to this procurement: 52.212-1, Instructions to Offerors - Commercial Items; 52.212-3 ALT I, Offeror Representations and Certifications - Commercial Items; 52.212-4, Contract Terms and Conditions - Commercial Items; 52.247-34, F.O.B. Destination; and 52.212-5, Contract Terms and Conditions Required to Implement Statutes or Executive Orders - Commercial Items with the following clauses applicable to paragraph (b): 52.219-8, Utilization of Small Business Concerns; 52.222-3, Convict Labor; 52.222-19, Child Labor ? Cooperation with Authorities and Remedies; 52.222-21, Prohibition of Segregated Facilities; 52.222-26, Equal Opportunity; 52.222-35, Equal Opportunity for Special Disabled Veterans, Veterans of the Vietnam Era, and Other Eligible Veterans; 52.222-36, Affirmative Action for Workers with Disabilities; 52.222-37, Employment Reports on Special Disabled Veterans, Veterans of the Vietnam Era, and Other Eligible Veterans; 52.232-33, Payment by Electronic Funds Transfer ? Central Contractor Registration. Quoters are reminded to include a completed copy of 52.212-3 ALT I with quotes. All clauses shall be incorporated by reference in the order. Additional contract terms and conditions applicable to this procurement are: 252.212-7000, Offeror Representations and Certifications - Commercial Items and 252.212-7001, Contract Terms and Conditions Required to Implement Statutes or Executive Orders Applicable to Defense Acquisitions of Commercial Items including 252.225-7001, Buy American Act and Balance of Payments Program; 252.225-7012, Preference for Domestic Commodities; 252.247-7023, 252.247-7024, Notification of Transportation of Supplies by Sea. At a minimum, responsible sources shall provide the following: a price quote on letterhead which identifies the requested item, with its unit price, extended price, total price, prompt pament terms, remittance address, TIN#, DUNS# and CAGE code. Responses to this solicitation are due by 7/14/2006, 3:00 P.M. local time. Offers can be e-mailed to Rachel.McFarland@navy.mil, faxed to 562-626-7877. Reference RFQ N00244-06-T-0592 on your quotation. Quoters must be registered in the CCR database to be considered for award. Registration is free and can be completed on-line at http://www.ccr.gov/. Quoters should also complete their Online Representations and Certifications Application (ORCA) at http://orca.bpn.gov.
- Web Link
-
Click here to learn more about FISC San Diego
(http://www.sd.fisc.navy.mil)
- Record
- SN01083874-W 20060708/060706221233 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |