SOLICITATION NOTICE
30 -- SHAFT, SHOULDERED
- Notice Date
- 12/5/2006
- Notice Type
- Solicitation Notice
- NAICS
- 333612
— Speed Changer, Industrial High-Speed Drive, and Gear Manufacturing
- Contracting Office
- DEPARTMENT OF THE AIR FORCE; 84 CSUG/PK;6050 GUM LANE BLDG 1215; HILL AIR FORCE BASE; UT; 84056
- ZIP Code
- 84056
- Solicitation Number
- FA8203-07-Q-70286
- Response Due
- 1/4/2007
- Archive Date
- 3/5/2007
- Small Business Set-Aside
- N/A
- Description
- PR Number(s): FD20200770286 Item: 0001 NSN: 3040002284716LE SHAFT,SHOULDERED P/N: 4G13366-101A, Description: SHAFT,SHOULDERED|11 UNTHREADED CROSS DRILLED|NOT IDENTICAL|12 EXTERNAL THREADED|9.260 INCHES NOMINAL|1.935 INCHES MINIMUM AND 1.936 INCHES MAXIMUM|SMALLER END HAS A BORE,0.060 IN. THRU AND 1.130 IN. DEEP,COUNTERBORED,0.120 IN. DIA. AND 1.220 IN. DEEP, AND TAP DRILLED 0.250 IN. WITH THE FOLLOWING SPEC: 1/4-28 UNF-2B,ALSO,THIS END HAS A KEYWAY,0.125 TO 0.135 IN. WIDE,CENTERED 85.0 TO 95.0 DEG. TO THE CROSS DRILL AT THE OPPOSITE END. THE LARGER END IS SLOTTED,0.877 TO 0.882 IN. WIDE AND 0.205 TO 0.235 IN. DEEP Total Line Item Qty: 262.0000 EA Applicable to: C-5B, C-5A Destn: SW3215,BARSTOW,CA.,92311-5014. Delivery: 18MAY2007, 262.00 EA PR Number(s): FD20200770286 Item: 0002 Description: FIRST ARTICLE TEST REPORT Total Line Item Qty: 1.0000 LO The anticipated award date will be:04JAN2007 Electronic procedure will be used for this solicitation. To: GOODRICH CORPORATION, CLEVELAND, OH.,44105-2060. To: WEST HEIGHTS MFG, KITCHENER, ONTARIO. To: HYDROMACH INC, CHATSWORTH, CA.,91311-8129. To: HEROUX DEVTEK INC, LONGUEUIL, QC. To: CM MANUFACTURING INC, MISSOULA, MT.,59808-8612. To: LOCKHEED MARTIN CORPORATION, MARIETTA, GA.,30063-0001. This part required engineering source approval by the design control activity in order to maintain the quality of the part. Existing unique design capability, engineering skills, and manufacturing knowledge by the qualified source(s) require acquisition of the part from the approved source(s). The approved source(s) retain data rights, manufacturing knowledge, or technical data that are not economically available to the Government, and the data or knowledge is essential to maintaining the quality of the part. An alternate source must qualify in accordance with the design control activity's procedures, as approved by the cognizant Government engineering activity. The qualification procedures must be approved by the Government engineering activity having jurisdiction over the part in the intended application. The requirements of FAR 9.202(A) have been completed and copies of the qualification requirements and standards may be obtained as described in this solicitation. Sources must be qualified prior to being considered for award. The solicitation will contain instructions of obtaining further information on this requirement. Award will be made only if the offeror, the product/service, or the manufacturer meets qualification requirements at the time of award in accordance with FAR clause 52.209-1. The solicitation identifies the office where additional information can be obtained concerning qualification requirements is cited in each individual solicitation. It is suggested that small business firms or others interested in subcontracting opportunities in connection with the described procurement make contact with the firm(s) listed. See Note(s) 26.
- Record
- SN01190916-W 20061207/061205220558 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |