Loren Data's SAM Daily™

FBO DAILY ISSUE OF APRIL 15, 2007 FBO #1966
SOLICITATION NOTICE

13 -- 400 cases: AMMUNITION, RIFLE, 5.56 CALIBER, 77 Grain Hollow Point Boat Tail Bullets

Notice Date

4/13/2007
 

Notice Type

Solicitation Notice
 

NAICS

332992 — Small Arms Ammunition Manufacturing
 

Contracting Office

ACA, Fort Benning, Directorate of Contracting, Building 6, Meloy Hall, Room 207, Fort Benning, GA 31905-5000
 

ZIP Code

31905-5000
 

Solicitation Number

W911SF-07-T-0048
 

Response Due

5/7/2007
 

Archive Date

7/6/2007
 

Small Business Set-Aside

N/A
 

Description

Contractor shall furnish 400 cases of 5.56mm ammunition with 77-Grain Hollow Point Boat Tail Bullet, on an ordered basis during the base period and two option periods, in accordance with military specifications. For the base period of 1 Jun 07 throu gh 31 May 08, with two, one year options. This is a Requirements type contract. NAICS Code is 332992, Standard 1000 employees. This requirement full and open competition. The point of contact for this action is LTC Yewston N. Myers, III, Contract Speci alist, (706)545-2420, yewston.myers@benning.army.mil. Offerors are reminded that you must be registered and currently active with Central Contractor Registration (CCR) (http://www.ccr.gov) to be eligible for award. Request for Quotation(W911SF-07-T-0048) will be available on or about 7 May 2007, and will be available at no cost on Army Single Face to Industry (ASFI) (http://acquisition.army.mil). All responsible offerors may submit offer which will be considered by this Agency. SPECIFICATIONS AND REQUIREMENTS 1. The contractor shall furnish ammunition in accordance with specifications shown below. 2. AMMUNITION, RIFLE, 5.56 CALIBER: a. BULLET: 77 Grain Hollow Point Boat Tail Bullet b. PRIMER & BRASS: Military Specs for brass hardness. Military Specs for primers or CCI #41 primers crimped in the brass. No waterproofing necessary on case mouth. Primers can be water proofed but not necessary. c. CARTRIDGE LENGTH: Over length not to exceed 2.260 inches when measured from tip of the bullet to the base of the cartridge. d. MUZZLE VELOCITY: Mussle velocity must average at least 2,750 feet per second (FPS) (plus or minus 25 FPS) measured at ambient temperature. When fired from 20 5.56mm barrels. e. All ammunition provided will be from the same production run. No lot shall be smaller than 50,000 rounds. A lot shall consist of the same lot of propellant, bullets, primers, and brass. f. ACCURACY STANDARDS: Must meet standard military accuracy specs for MK262. Must AVG less than 3.5 inches extreme spread at 300 yards or 300 meters for five of each ten shot groups. Groups will be fired from an accuracy test bolt rifle, from an accur acy fixture. No one ten shot group shall exceed 3.5 inches. g. FUNCTIONAL CHARACTERISTICS: Candidate ammunition must function and operate routinely in M16 style rifles. Must meet standard military pressure and function specs for 77gr 5.56mm ammunition. Ammunition must burn clean and leave no residue.
 

Place of Performance

Address: ACA, Fort Benning Directorate of Contracting, Building 6, Meloy Hall, Room 207 Fort Benning GA

Zip Code: 31905-5000

Country: US
 

Record

SN01273043-W 20070415/070413221104 (fbodaily.com)
 

Source

FedBizOpps Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's FBO Daily Index Page |