SOLICITATION NOTICE
34 -- DRESSER, DISHWASHER LANDING & SINK PRE-WASH
- Notice Date
- 5/2/2007
- Notice Type
- Solicitation Notice
- NAICS
- 332312
— Fabricated Structural Metal Manufacturing
- Contracting Office
- Department of Homeland Security, United States Coast Guard (USCG), Commanding Officer, USCG Engineering Logistics Center, 2401 Hawkins Point Road Building 31, Mail Stop 26, Baltimore, MD, 21226-5000, UNITED STATES
- ZIP Code
- 00000
- Solicitation Number
- HSCG40-07-Q-41074
- Response Due
- 5/16/2007
- Archive Date
- 5/31/2007
- Small Business Set-Aside
- Total Small Business
- Description
- This is a combined Synopsis/Solicitation for Commercial Items prepared in accordance with the format in subpart 12.6 of the FAR, FAC 2005-16 and as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. Those interested in submitting a quotation shall request a copy of Drawing Number 618-WMEC-651-002. The Point of Contact is Ron Almond. E-mail: ronald.almond@uscg.mil or you may call (410) 762-6451. The USCG Engineering Logistics Center has a requirement for the following commercial items: ITEM 1. DISHWASHER LANDING DRESSER, STAINLESS STEEL COMPLETE WITH TOP, LEGS W/STRETCHERS, SHELF AND SEA RAILS TO BE USED ABOARD A U.S. COAST GUARD CUTTER. THE SCULLERY DISHWASHER LANDING DRESSER SHALL BE CONSTRUCTED USING THIS SPECIFICATION AND COAST GUARD DRAWING 210-WMEC-651-002. WHERE THIS SPECIFICATION AND THE DRAWING DIFFER, THIS SPEC SHALL TAKE PRECEDENCE. FOR DESIGN PURPOSES THE MAIN DECK OF THE CUTTER HAS BOTH SHEER AND CAMBER. THE DISHWASHER LANDING DRESSER UNIT SHALL BE CAPABLE OF BEING DISASSEMBLED AND REASSEMBLED FOR INSTALLATION ABOARD THE CUTTER. ALL COMPONENT PIECES SHALL BE SMALL ENOUGH IN SIZE TO PASS THROUGH A 26 INCH X 66 INCH OPENING WITH 8 INCH RADIUS CORNERS. THIS DRESSER SHALL BE RECTANGULAR IN SHAPE, WITH OVERALL DIMS OF 74 INCH WIDE X 30 INCH DEEP X 44 INCH HIGH TO TOP OF BACK SPLASH AND CONSIST OF THE FOLLOWING COMPONENTS: A TOP, LEGS W/STRETCHERS, A SHELF, AND REMOVABLE SEA RAILS. ALL OF WHICH SHALL BE OF TYPE 304 STAINLESS STEEL WITH A #4 FINISH. THE TOP SHALL BE FURNISHED IN ONE PIECE. HOWEVER, IT MAY BE FABRICATED IN MORE THAN ONE PIECE. IF FABRICATED IN MORE THAN ONE PIECE THE WELDED CONNECTIONS SHALL BE GROUND AND POLISHED TO MATCH THE SURROUNDING AREAS. THE BACK SPLASH SHALL BE 8-INCHES HIGH, LOCATED AT THE BACK AND RIGHT SIDE, AND FABRICATED FROM THE SAME SHEET AS THE TOP. THERE SHALL BE A MINIMUM RADIUS OF 3/4 INCH WHERE THE BACK SPLASH AND THE TOP SURFACE MEET. THE TOP OF THE BACK SPLASHES SHALL BE FLANGED BACK @ 45 DEGREES. THE FRONT EDGE OF THE DRESSER TOP SHALL BE MANUFACTURED WITH A MARINE EDGE TO PREVENT SPILLAGE IN A SEAWAY. THE EDGE SHALL EXTEND UPWARD A MINIMUM OF 3/4 OF AN INCH ABOVE THE SURFACE OF THE TOP AND THEN DOWN 1-1/2 INCHES AND UNDER 1/2 INCH TO FORM A FINISHED APPEARANCE. THE LEFT END OF THE DRESSER TOP SHALL NOT HAVE A MARINE EDGE BUT BE FLANGED TO MATE WITH A HOBART MODEL NO. AM-15 DISHWASHER. ALL COMPONENT PIECES SHALL BE ASSEMBLED BY THE VENDOR FOR PROPER FIT. HOLES FOR THE ATTACHING FASTENERS SHALL THEN BE DRILLED AND THE COMPONENTS SHALL BE BOLTED TOGETHER. AFTER THE VENDOR IS SATISFIED WITH THE FIT, HE MAY THEN, IF HE DESIRES, DISASSEMBLED AND PACKAGE THE COMPONENTS FOR SHIPPING. ALL FASTENERS AND LOOSE PIECES FOR THIS UNIT SHALL BE PACKAGED TOGETHER AND SHIPPED WITH THAT UNIT FOR REASSEMBLY. ALL MATERIALS USED IN CONSTRUCTION SHALL NOT AFFECT THE TASTE OF THE FOOD. STAINLESS STEEL SURFACES EXPOSED TO VIEW SHALL HAVE A NO.4 FINISH PER NATIONAL SANITATION FOUNDATION STANDARDS. ALL VISIBLE STAINLESS STEEL WELDS SHALL BE GROUND AND POLISHED TO A #4 FINISH TO MATCH SURROUNDING AREAS. ALL SHARP AND ROUGH EDGES SHALL BE GROUND SMOOTH TO PREVENT INJURY TO PERSONNEL. INACCESSIBLE VOIDS SHALL BE MADE VERMIN PROOF. HARDWARE SHALL BE HEAVY DUTY MARINE GRADE OF EITHER CHROME PLATED BRASS/BRONZE OR SATIN STAINLESS STEEL. SEAL ALL CREVICES, LAP JOINTS, SMALL GAPS AND INACCESSIBLE AREAS WITH SILICONE SEALER G E, RTV-108 OR EQUAL. PARTICULAR ATTENTION SHALL BE GIVEN TO SANITARY FEATURES AND THE RECOMMENDATIONS OF THE U.S. PUBLIC HEALTH SHALL PREVAIL, WHERE APPLICABLE. THE SIZE, CONFIGURATION, ARRANGEMENT AND SPECIFICATIONS OF THIS DRESSER UNIT SHALL ALSO BE IN ACCORDANCE WITH COAST GUARD DRAWING 210 WMEC-651-002. QUANTITY: (1) ONE EACH. ITEM 2. SINK/PRE-WASH DRESSER, STAINLESS STEEL COMPLETE WITH TOP, SINK, SHELF AND LEGS TO BE USED ABOARD A U.S. COAST GUARD CUTTER. THE SCULLERY SINK & DRESSER SHALL BE CONSTRUCTED USING THIS SPECIFICATION AND COAST GUARD DRAWING 210-WMEC-651-002. WHERE THIS SPECIFICATION AND THE DRAWING DIFFER, THIS SPECIFICATION SHALL TAKE PRECEDENCE. FOR DESIGN PURPOSES THE MAIN DECK OF THE CUTTER HAS BOTH SHEER AND CAMBER. THE SINK/PRE-WASH DRESSER UNIT SHALL BE CAPABLE OF BEING DISASSEMBLED AND REASSEMBLED FOR INSTALLATION ABOARD THE CUTTER. ALL COMPONENT PIECES SHALL BE SMALL ENOUGH IN SIZE TO PASS THROUGH A 26 INCH X 66 INCH OPENING WITH 8 INCH RADIUS CORNERS. THE DRESSER SHALL BE (L) SHAPE IN CONFIGURATION WITH OVERALL DIMENSIONS OF 76 INCH X 71-3/4 INCH X 44 INCH HIGH TO TOP OF BACK SPLASH AND CONSIST OF FOUR MAJOR COMPONENTS. A TOP, SINK, LEGS W/STRETCHERS AND A SHELF, ALL OF WHICH SHALL BE OF TYPE 304 STAINLESS STEEL WITH A #4 FINISH. THE TOP SHALL BE FURNISHED IN ONE PIECE. HOWEVER, IT MAY BE FABRICATED IN MORE THAN ONE PIECE. IF FABRICATED IN MORE THAN ONE PIECE THE WELDED CONNECTIONS SHALL BE GROUND AND POLISHED TO MATCH THE SURROUNDING AREAS. THE BACK SPLASH SHALL BE 8-INCHES HIGH AND FABRICATED FROM THE SAME SHEET AS THE TOP. THERE SHALL BE A MINIMUM RADIUS OF 3/4 INCH WHERE THE BACK SPLASH AND THE TOP SURFACE MEET. THE TOP OF THE BACK SPLASHES SHALL BE FLANGED BACK @ 45 DEGREES. THE FRONT EDGES AND LEFT END OF THE DRESSER TOP SHALL BE MANUFACTURED WITH A MARINE EDGE TO PREVENT SPILLAGE IN A SEAWAY. THE EDGE SHALL EXTEND UPWARD A MINIMUM OF 3/4 OF AN INCH ABOVE THE SURFACE OF THE TOP AND THEN DOWN 1-1/2 INCHES AND UNDER 1/2 INCH TO FORM A FINISHED APPEARANCE. THE RIGHT END OF THE DRESSER TOP SHALL NOT HAVE A MARINE EDGE BUT BE FLANGED TO MATE WITH A HOBART MODEL NO. AM-15 DISHWASHER. THE UNIT SHALL HAVE ONE (1) STAINLESS STEEL, WELDED IN TYPE SINK. THE DIMENSION OF THE SINK SHALL BE 24 INCHES WIDE X 18 INCHES FRONT TO BACK X 12 INCHES DEEP AND FABRICATED OF MIN 12-GAUGE STAINLESS STEEL. THE SINK SHALL HAVE GENEROUS 3/4 INCH RADIUS WHERE THE SIDES OF THE SINK MEET THE BOTTOM AND ONE ANOTHER. THE INTERSECTION WHERE THE SINKS BLENDS INTO THE TOP SHALL HAVE A MIN RADIUS OF 1/4 INCH. THE BOTTOM OF THE SINK SHALL BE SLOPED FOR DRAINAGE AND HAVE A DISHED RECESSED HOLE FOR A 3-1/2 INCH DIAMETER BASKET STRAINER. THE UNDERSIDE OF THE TOP AND SINK SHALL BE TREATED WITH INERT SOUND DEADENING MATERIAL. ALL COMPONENT PIECES SHALL BE ASSEMBLED BY THE VENDOR FOR PROPER FIT. HOLES FOR THE ATTACHING FASTENERS SHALL THEN BE DRILLED AND THE COMPONENTS SHALL BE BOLTED TOGETHER. AFTER THE VENDOR IS SATISFIED WITH THE FIT, HE MAY THEN, IF HE DESIRES, DISASSEMBLED AND PACKAGE THE COMPONENTS FOR SHIPPING. ALL FASTENERS AND LOOSE PIECES FOR THIS UNIT SHALL BE PACKAGED TOGETHER AND SHIPPED WITH THAT UNIT FOR REASSEMBLY. ALL MATERIALS USED IN CONSTRUCTION SHALL NOT AFFECT THE TASTE OF THE FOOD. STAINLESS STEEL SURFACES EXPOSED TO VIEW SHALL HAVE A NO. 4 FINISH PER NATIONAL SANITATION FOUNDATION STANDARDS. ALL VISIBLE STAINLESS STEEL WELDS SHALL BE GROUND AND POLISHED TO A #4 FINISH TO MATCH SURROUNDING AREAS. ALL SHARP AND ROUGH EDGES SHALL BE GROUND SMOOTH TO PREVENT INJURY TO PERSONNEL. INACCESSIBLE VOIDS SHALL BE MADE VERMIN PROOF. HARDWARE SHALL BE HEAVY DUTY MARINE GRADE OF EITHER CHROME PLATED BRASS/BRONZE OR SATIN STAINLESS STEEL. SEAL ALL CREVICES, LAP JOINTS, SMALL GAPS AND INACCESSIBLE AREAS WITH SILICONE SEALER G E, RTV-108 OR EQUAL. PARTICULAR ATTENTION SHALL BE GIVEN TO SANITARY FEATURES AND THE RECOMMENDATIONS OF THE U.S. PUBLIC HEALTH SHALL PREVAIL, WHERE APPLICABLE. THE SIZE, CONFIGURATION, ARRANGEMENT AND SPECIFICATIONS OF THIS DRESSER UNIT SHALL ALSO BE IN ACCORDANCE WITH COAST GUARD DRAWING 210 WMEC-651-002. QUANTITY: (1) ONE EACH. ITEM 3. DRAWING APPROVAL REQUIREMENTS: THE CONTRACTOR IS RESPONSIBLE FOR FURNISHING DRAWINGS FOR APPROVAL IN ELECTRONIC FORMAT. THESE DRAWINGS MAY BE STANDARD MANUFACTURES DRAWINGS. THE DRAWINGS AS A MINIMUM SHALL INCLUDE ALL THE INFORMATION SPECIFIED ABOVE. THEY SHALL INCLUDE ALL OUTLINE AND KEY DIMENSIONS AND A PARTS LIST OR BILL OF MATERIAL FOR ALL PARTS OR COMPONENTS FURNISHED WITH THE UNIT. THE DRAWINGS MAY BE GENERIC IN NATURE BUT SHALL DEPICT BY NOTE OR OTHER MEANS INFORMATION TO ENSURE THE CONTRACTOR IS MEETING ALL OF THE REQUIREMENTS SPECIFIED HEREIN. THE COAST GUARD SHALL REVIEW THE DRAWINGS FOR COMPLIANCY WITH THE SPECIFICATION AND RETURN ONE SET TO THE CONTRACTOR FOR CORRECTION. QUANTITY: (4) FOUR EACH. ITEM 4. FINAL DRAWING REQUIREMENTS: THE CONTRACTOR SHALL FURNISH (2) PAPER SETS AND (1) ELECTRONIC SET OF APPROVED AS CORRECTED DRAWINGS. THE ELECTRONIC DRAWINGS SHALL BE IN THE AutoCADTM FORMAT (VERSION 2005). THE FILE MAY BE COPIED TO A 3-1/2 FLOPPY DISK OR IF THE FILE IS LARGER THAN THE 1.44 MB IS SHALL BE COPIED TO A CD-ROM DISK. QUANTITY: (1) ONE SET. The following FAR clauses apply to this solicitation. Offerors may obtain full text versions of these clauses electronically at http://www.arnet.gov/far. FAR 52.212-1 Instructions to Offerors-Commercial Items (Sept 2006). 52.212-2 Evaluation-Commercial Items-Pricing consideration and past performance are evaluation factors (Jan 1999). FAR 52.212-3 Offeror Representations and Certifications-Commercial Items (Nov 2006) with Alt 1 included. FAR 52.212-4 Contract Terms and Conditions-Commercial Items (Sept 2005). FAR 52.212-5 Contract Terms and Conditions Required to Implement Statues or Executive Orders, Commercial Items (Nov 2006). The following clauses listed in 52.212-5 are incorporated: 52.219-8, Utilization of Small Business Concerns (May 2004)(15 U.S.C.637(d)(2)and(3); 52.222-3 Convict labor (June 2003) (E.O. 11755); 52.222.19 Child Labor-Cooperation with Authorities and Remedies (Jan 2006) (EO 11755); 52.222-21, Prohibition of Segregated Facilities (Feb 1999); 52.222-26 Equal Opportunity (Apr 2002)(E.O. 11246); 52.222-35, Equal Opportunity for Special Disabled Veterans, Veterans of the Vietnam Era, and other Eligible Veterans (Sept 2006) (38 U.S.C. 4212) 52.222-36 Affirmative Action for Workers with Disabilities (JUN 1998)(29 U.S.C. 793).52.222-37, Employment Reports on Special Disabled Veterans, Veterans of the Vietnam Era and other Eligible Veterans (Sept 2006)(38 U.S.C. 4212). 52.225-1, Buy American Act-Supplies (April 2006)(41 U.S.C. 10a-10d); 52.225-13,Restrictions on Certain Foreign Purchases (April 2006) (E.o.s, proclamations, and statutes administered by the Office of Foreign Assets Control of the Department of the Treasury).; 52.232-33 Payment by Electronic Funds Transfer Central Contractor Registration (July 2006)(21 U.S.C. 3332). The following items are incorporated as addenda to this solicitation: 3052.209-70 Prohibition on contracts with corporate expatriates. (June 2006) Copies of HSAR clauses may be obtained electronically at http://www.dhs.gov.
- Record
- SN01285716-W 20070504/070502221833 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |