Loren Data's SAM Daily™

fbodaily.com
Home Today's SAM Search Archives Numbered Notes CBD Archives Subscribe
FBO DAILY ISSUE OF JUNE 16, 2007 FBO #2028
SOLICITATION NOTICE

71 -- Storage Lockers

Notice Date
6/14/2007
 
Notice Type
Solicitation Notice
 
NAICS
337215 — Showcase, Partition, Shelving, and Locker Manufacturing
 
Contracting Office
Department of the Air Force, Direct Reporting Units, USAF Academy - 10 MSG/LGC, 8110 Industrial Drive Suite 200, USAF Academy, CO, 80840-2315, UNITED STATES
 
ZIP Code
00000
 
Solicitation Number
FA7000-07-T-0156
 
Archive Date
7/31/2007
 
Small Business Set-Aside
Total Small Business
 
Description
This is a pre-solicitation notice for the following: The requirement to manufacture, install and assemble 781 storage lockers at the United States Air Force Academy in Colorado Springs, CO. The requirement is: CLIN 0001 - 10 gauge 2ft x 2ft welded wire mesh single tier add ons 3ft x 3ft x 7ft high, 388 each. CLIN 0002 - 10 gauge 2ft x 2ft welded wire mesh double tier starters 3ft x 3ft x 7ft high, 44 each. CLIN 0003 - 10 gauge 2ft x 2ft welded wire mesh double tier add ons 3ft x 3ft x 7ft high, 264 each. CLIN 0004 - 10 gauge 2ft x 2ft welded wire mesh single tier starters 3ft x 3ft x 7ft high, 85 each. CLIN 0005 - Installation of the lockers, 781 each. The lockers need to be manufactured to the dimensions set forth by customer as shown below and in accordance with the Occupational Safety and Health Administration (OSHA) and the American National Standards Institute (ANSI) safety guidelines. Single tier lockers with one hinged door, double tier lockers with two hinged doors. All lockers are with ceilings. Single tier starter is required with solid metal tops and bottoms and solid backs with a size of 3ft wide, 3ft deep and 7ft high. Lockers require a hasp latch, double tier starters, and add-ons as solid metal shelf. The back of the locker is solid as well. The contractor will assemble storage lockers on-site and lockers will need to be anchored to the floor usining a flat plate connected to the 2 x2 posts. Lockers will also be anchored tot the wall swith angle iron every 4 to 6 units. All single tier and add-ons should be able to bolt to each other. The finish is Gray (Powder Coated). For the installation, the contractor shall provide all management, tools, supplies, equipment, hardware, anchors and labor necessary to ensure that the manufacturing, installation, and assembling of the lockers. Install angle iron to wall to prevent lockers from falling over. Contractor shall clean up work area and dispose of waste after installation. The installation needs to start the beginning of October 2007 if at all possible. The delivery and installation of the lockers will have to be performed during normal duty hours (7:30am to 5:00 pm). The contractor would need to ship and install the lockers on a schedule worked out with the user. The contractor shall install the storage lockers in 55 storage rooms for a grand total of 781 lockers. Request for quotation (RFQ) FA7000-07-T-0156 will be available on or about 20 June 2007. The RFQ closing will be on or about 3 July 2006. The RFQ will be made available electronically on FedBizOpps. No hard copies will be available. All propspective contractor must be registered in the Central Contractor Registration by the proposal due date to be considered. The North American Industry Classification System Code (NAICS) is 337215 and the small business size standard is 500 employees. This is a 100% small business set-aside.
 
Place of Performance
Address: United States Air Force Academy, Colorado Springs, CO
Zip Code: 80840
Country: UNITED STATES
 
Record
SN01319004-W 20070616/070614221155 (fbodaily.com)
 
Source
FedBizOpps Link to This Notice
(may not be valid after Archive Date)

FSG Index  |  This Issue's Index  |  Today's FBO Daily Index Page |
ECGrid: EDI VAN Interconnect ECGridOS: EDI Web Services Interconnect API Government Data Publications CBDDisk Subscribers
 Privacy Policy  Jenny in Wanderland!  © 1994-2024, Loren Data Corp.