SOURCES SOUGHT
23 -- Armored Truck Tractor 6X6
- Notice Date
- 9/5/2007
- Notice Type
- Sources Sought
- NAICS
- 336120
— Heavy Duty Truck Manufacturing
- Contracting Office
- Department of the Navy, Naval Facilities Engineering Command, NAVFAC Southwest, Specialty Center Contracts Core, 1205 Mill Road Building 850, Port Hueneme, CA, 92043-4347, UNITED STATES
- ZIP Code
- 00000
- Solicitation Number
- N62583-ARMOREDTRUCKTRACTOR6X6
- Response Due
- 10/5/2007
- Description
- Description This is a SOURCES SOUGHT ANNOUNCEMENT, a Market Survey for written information only. This is not a solicitation announcement for proposals and no contract will be awarded from this announcement. No reimbursement will be made for any costs associated with providing information in response to this announcement or any follow-up information requests. No telephone calls will be accepted requesting a bid package or solicitation. There is no bid package or solicitation in order to protect the procurement integrity of any future procurement, if any, that may arise from this announcement, information regarding the technical point of contract will not be given and no appointments for presentations will be made.------ The general Scope of Work is the Naval Facilities Engineering Logistics Center (NFELC), Port Hueneme, CA is seeking sources for Expeditionary Truck Tractor 6X6.------ The Options to the Expeditionary Truck Tractor 6X6, but not limited to following:----- Truck Shall Meet Requirements for Severe Service Operation; Conventional Extended Cab 75 inches in length, 74 inches in width, 65 inches in height with Front End Tilting, Fiberglass with Stationary Grill with Two Piece Windshield; Integral Armored Cab Level 1 Type Shall Utilize Air Ride Cab Suspension; Truck Shall Be 60,000 Gross Vehicle Weight Rating; Chassis Configuration Shall Be 6X6; Frame, All Heat Treated Alloy Steel (110,000 PSI Yield); Frame Shall Have C-channel Reinforcements to Resist Bending Motion; Frame Crossmembers, Fuel Tanks, Battery Boxes, and Suspension Shall; Be Fastened With Huck Spin Fasteners; Frame 368? Over All Length; Front Tow Loop with Integral Lifting and Tie-Downs, In Accordance With, Federal Standard 209K; Wheelbase 214 inches With 11 inches Ground Clearance Minimum and 30 inches Fording Capability; Engine Caterpillar C-15 435HP at 2100 RPM with Compression Brake Must Be JP8, Compatible; Engine Cooling System Shall Have Extended Life Coolant; Engine Shall Be Equipped with a Pre-Cleaner and Dual Element Air Filter and Have a; Air Cleaner Restriction Indicator, Mounted in Cab; Exhaust Configuration Shall Be Vertical Muffler and Tailpipe Mounted Right Side; Allison Transmission HD-4560P 6 Speed with Transmission Cooler and Oil Level, Sensor and With Power Take Off Provision; Engine, Transmission, Transfer, and Differentials Equipped With Magnetic Drain Plugs; PTO Hydraulic Pump to Provide 20-35 GPM with 2000PSI; PTO Control Shall Be Dash Mounted With Operators Decal; Heavy Duty Two Speed Transfer Case with Front Axle Engage Switch, With Indicator Axle Lock Light; Driver Controlled Differential Locking and Power Divider Lock with Indicator Locked, Lights Preferred; Dash Mounted Push Button Type Transmission Control Panel; Dash Mounted CTIS Central Tire Inflation System. Dana, Electronic Controlled System, with Selectable Terrain Settings Preferred; Multi Position Tilting and Telescoping Steering Column Preferred; Dual Power Steering Gears Preferred; Front Axle 23,000Lb Capacity with 24,000 Capacity Multileaf Springs with Torque Rods; Rear Axle Tandem 52,000Lb Capacity; Suspension Rear Tandem, Hendrickson RT-523 Multileaf Walking Beam, 52,000 Capacities with Bronze Center Bushings; Heavy Duty Front Bumper Swept Back 40 Degrees with In Bumper Headlight; Provisions and Bumper Mounted Brush Guard or Radiator Guard, Made Of Tubular Steel; ABS Brake System Must Be Provided; All Air Lines Preferred With Quality Connect Fittings and, Air Tank Drain Pull Cords with Easy Access; Automatic Slack Adjusters Preferred On All Axles; Brake Dust Shields Preferred Front and Rear Axles; Air Brakes Rear S Cam 16.5x7, Front S Cam 16.5x6; Spring Brakes Both Rear Axles; Air Dryer is required with Air Brake System; 12/24 Volt System with 24Volt NATO Slave Jump Plug; Battery Disconnect Switch Located Out Side of Cab Preferred; Battle Switch Type Ignition Switch Preferred; Electrical System Shall Utilize Manual Reset Circuit Breakers; Trailer Connections to Provide For 12/24 Plugs and ABS Power Plug; Pogo Stick with Trailer Coiled Air Lines and Glad Hand Connections with Trailer Light Coiled Cords Preferred; An Electrical System Electronic Control Module must be provided to monitor Electrical System Functions and Provide in Cab Fault Codes for Troubleshooting; Cab Dome Lights Preferred; Rear Work Lights R&L to Illuminate Platform at Rear of Cab; Tail Lights and Marker Lights to Be LED, and Halogen Headlights Preferred; Fuel Tank Shall Provide 100 U.S. Gallon Capacity for 400 Minimum and 600 Preferred Mile Range, Fuel Tank Shall Be Made of Steel; Maximum Desired Speed of 65mph; Unit Capable To Sustain 45mph On 6 percent Grade Loaded; Engine Mounted Fuel Filter Preferred With 250 Micron Rating; Fuel/Water Separator Preferred; 50 Gallon Capacity Hydraulic Tank Preferred For Wet Kit; Fifth Wheel Type: 2 inches King Pin NO-TILT CONVERTIBLE Air Operated Slider with, Left hand Roadside Release; Small Approach Ramps Preferred From Frame Ends to Fifth Wheel; Fifth Wheel Height Not To Exceed 57 inches; Wet Kit Provisions Shall Be Mounted In Front of Fifth Wheel on Cat Walk or Platform; Two Tier Steps Will Be Provided To Access Cat Walk or Platform at Rear of Cab; Wet Kit Connections Are To Be Quick Disconnects Using Industry Standards; West Coast Style Mirrors Right and Left with Lower Convex Shall be Cab Mounted with Breakaway Feature; Cab Steps Shall Be Offset and Exterior Grab Handles Preferred; Cab Exterior Sun Shade Preferred with Integral LED Clearance Lights; Passenger Side Look down Mirror Preferred; Cab Storage Shall Include Driver and Passenger Overhead Storage Bins with Safety Nets; Cab Storage Shall Include Behind Seats with Removable Cargo Net; Cab Interior Grab Handles Preferred; Cab Floor Mats Rubber Preferred; All Cab Glass Tinted Preferred; Driver and Passenger Sun Visors Preferred; Driver and Passengers Seats Air Ride with High Back Integral Headrests Preferred; Driver and Passenger Seat Preferred With Three Point Seat Belt System; Cup Holders Preferred; Coat Hooks inside Rear Cab Wall Preferred; Dash Wing Panel, Which Brings Switches Closer To Driver Preferred; Gauges Provided In Gauge Cluster Shall Include; Speedometer, Tachometer, Engine Oil Pressure, Engine Oil Temp, Coolant Temp, Transmission Temp, Fuel Level, Voltmeter, Low Oil Lights For Axles, and Air Pressure Gauges W/Low Air Warnings and Buzzers; Electronic Cruise Control Preferred; Wing Panel Switches Shall Have Back Lighting for Night Visibility; Air and Electric Horn Preferred; High Output Air Conditioner with integral Heater and Defroster; Provide Glad-hands At Rear of Frame and 24V Trailer Plug; Unit to Have 30,000LB Capacity Pintal Hook Provided With Plate Mounted at Rear of Frame with Tow Hook Mounting Provisions or eyelets on Rear Plate; Wheels 7, 20 inches x 10 inches Two Piece Bolted, Steel Disc; Tires 7, 16.00R20 with Wheel Track of 78 inches -80 inches Preferred; Provide Spare Tire and Wheel Mounted To Rear Spare Tire Carrier; Provide 20T Jack, Lug Wrench, and Bar, In Frame Mounted Tool Box; Quarter Fenders Front of Tandems; Rear Removable Mud Flaps and Hangers will be provided; Paint Unit from Frame up With Desert Tan 33303, Paint Lusterless Black for All Parts Added to the Truck Frame; Safety Equipment to Include Reflector Kit and Five Pound Fire Extinguisher; Customer Support Books, Service, Repair, and Parts; Full Service and Dealer Network in Middle East as Well as World Wide Parts; Optional Extended Warranty and or Field Service Representative; Capability to Obtain Parts in Theater within 24 Hours;---------- Interested sources should respond with brief documentation showing the company?s ability to fulfill the requirements described below. Interested sources will indicate whether they offer the capability for manufacturing of the Armored Truck Tractor 6X6. Interested sources will briefly summarize their corporate history, and level of experience with manufacture of Armored Truck Tractor 6X6. Interested sources will indicate whether their services also include product support. The principal recipients of the Expeditionary Truck Tractor 6X6, are the NFELC Port Hueneme. In preparation for a future procurement, The Naval Facilities Engineering Logistics Center (NFELC), Port Hueneme, CA is performing a ?market research? to determine potential businesses that can perform all the tasks listed in the General Scope of Work. Comments must be received on or before 05 October 2007. Interested sources must submit any information relating to this announcement in writing via e-mail to Maria.Nailat@navy.mil Responses received after this deadline may not be considered. Since this is a sources sought announcement, no evaluation letters will be issued to the participants.
- Place of Performance
- Address: To Be Determined
- Zip Code: 93043
- Country: UNITED STATES
- Zip Code: 93043
- Record
- SN01395876-W 20070907/070905222032 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |