SOLICITATION NOTICE
54 -- Phillips Storage Tanks
- Notice Date
- 7/14/2008
- Notice Type
- Presolicitation
- Contracting Office
- Department of the Interior, Bureau of Land Management, National Centers Region, BLM-BC NATIONAL BUSINESS CENTER* BC663 BLDG 50, DFC, PO BOX 25047 DENVER CO 80225
- ZIP Code
- 80225
- Solicitation Number
- NAB080115
- Response Due
- 8/6/2008
- Archive Date
- 7/14/2009
- Point of Contact
- Amelia V. Rocha Contract Specialist 3032369424 Amelia_Rocha@blm.gov;
- Small Business Set-Aside
- Total Small Business
- Description
- Bureau of Land Management Invitation for Bids, NAB080115 - 8 Fiberglass Storage Tanks 25,000 Gallons for the Malta Field Office, 501 S 2nd Street East, Malta, MT 59538.REQUIREMENTS Loading Conditions - Tank shall meet the following design criteria: 1. Internal Load - Tank shall withstand a 5-psig air-pressure test with 5:1 safety factor. When tank is designed for on-site testing, contractor shall individually test tank for leakage prior to installation. Maximum test pressure is 5 psig (3 psig for a 12 foot-diameter tank).2. Vacuum Test - To verify structural integrity, every 10 feet-diameter tank and smaller shall be designed to withstand a vacuum test to 11.5 inches of mercury.3. Surface Loads - Tank shall withstand surface H-20 axle loads when properly installed according to tank manufacturers current Installation Manual and Operating Guidelines.4.External Hydrostatic Pressure - Tank shall be capable of being buried in ground with 7feet of overburden over the top of the tank, the hole fully flooded and a safety factor of 5:1 against general buckling.5. Surface Load - Tank shall withstand surface H-20 axle loads when properly installed according to tank manufactures current Installation Manual and Operating Guidelines.6. Tank shall support accessory equipment - such as internal pump platforms, drop/fill tubes, submersible pumps and ladders - when installed according to tank manufacturers current Installation Manual and Operating Guidelines.Product Storage1. Tank shall be capable of storing water products with specific gravity up to 1.1.2. Tank shall be vented to atmospheric pressure. 3. Tank shall be capable of storing products identified in the manufacturer's current standard limited warranty.Materials1. Tank shall be manufactured with 100% resin and glass-fiber reinforcement. No sand fillers.2. The laminate materials used in the internal coating system of a potable water tank shall conform to the requirements of NSF Standard 61.Tank Dimensions 1. Tank shall have nominal capacity of 25000 gallons.2. Tank shall have nominal outside diameter of 10 feet.3. Tank shall have approximate overall length of 47 feet and 6 3/4 inches.ACCESSORIESOptional Anchor Straps1. Straps shall be FRP anchor straps as supplied by tank manufacturer. 2. Number and location of straps shall be specified in current literature by tank manufacturer.Optional Man-ways1. Each tank shall have a manway, it shall be flanged and 30 inches nominal diameter, complete with gasket, bolting hardware and FRP cover. 2. Actual location shall be shown on tank shop drawings, and approved by Contracting Officer.3. Each manway shall have an extension constructed of FRP. Length will be approved on shop drawing. The extension shall be designed to withstand all expected loads, and an H-20 axial load. 4. All tanks for potable/ stock water use require at least one manway, and extension.5. Approved shop drawings shall show exact location of the manway.Optional Fittings1. Each tank shall have one air vent fitting at the top of the radius of the tank. These fittings shall be 4 inches dia. flat-faced and flanged, and shall conform to ANSI B16.5 150 # bolting pattern..2. Each tank shall have (2) FRP bottom dome nozzles 4 inches dia., they shall be flat-faced and flanged, and shall conform to ANSI B16.5 150 # bolting pattern.3. Each tank shall have a FRP top dome nozzle 4 inches dia., they shall be flat-faced and flanged, and shall conform to ANSI B16.5 150 # bolting pattern.4. All FRP and PVC nozzles shall be flat-faced and flanged, and shall conform to ANSI B16.5 150# bolting pattern.Optional Access Openings (not for use with potable water tanks)1. FRP access openings shall be 30 inches in diameter2. PVC Risers and FRP lids shall be provided by the tank manufacture for field installation on access openings.3. Hinged and Lockable manway extension. Total height to be 4 feet w/12 inches gel coat above grade. Color of gel coat shall be tan.TESTING1. Tank shall be tested according to the Manufacturer's Installation Manual and Operating Guidelines in effect at time of installation.WARRANTY1. Warranty shall be manufacturer's warranty for underground water and potable water tanks in effect at time of delivery and extend 1 year. Delivery is for 3/15/2009 and 4/1/2009 Drawings and additional specifications will be attached to the solicitation. The solicitation shall be posted on or by Wednesday, July 16, 2008. This is a 100% set-aside for small business. The standard NAICS classification is 326199. Size standard is 500 employees. Bids are due Tuesday, August 6, 2008 by 11:00 AM Mountain Time. Send bids by U.S. Mail to: Department of the Interior; BLM, OC-663; Attention: Amelia Rocha; BLDG 50, DFC, PO Box 25047; Denver, CO 80225-0047. By express or hand delivery: Department of the Interior; BLM, OC-663; Attention: Amelia Rocha; Mail Room, Entrance S-4; BLDG 50, Denver Federal Center; Denver, CO 80225, or by facsimile to (303) 236-9421. An award will be made to the lowest bid with acceptable past performance. Submit offers to the address indicated above. Bids shall include the following items: 1) Pricing schedule including a unit price for each line item, 2) Completed 52.212-3 Representations and Certifications - Commercial Items (Nov 2007) (accessible at http://www.arnet.gov/far/), or 3) a Statement of vendor's registration with ORCA http://orca.bpn.gov, 4) Include TIN and DUNS Number, 5) Bids must be signed. 6) Offeror must be registered and active at http://www.ccr.gov to be considered for award.
- Web Link
-
FedBizOpps Complete View
(https://www.fbo.gov/?s=opportunity&mode=form&id=cce2177dfe7429274f6589a989933085&tab=core&_cview=1)
- Place of Performance
- Address: Malta, MT
- Zip Code: 59538
- Zip Code: 59538
- Record
- SN01613702-W 20080716/080714223256-cce2177dfe7429274f6589a989933085 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |