MODIFICATION
95 -- AMENDMENT 0001 TO SOLICITATION W25G1V-09-R-0022 FOR MULTIPLE METAL ITEMS USED IN FABRICATION OF INTEGRATED ELECTRICAL RACKS FOR TOBYHANNA ARMY DEPOT, TOBYHANNA PA
- Notice Date
- 6/16/2009
- Notice Type
- Modification/Amendment
- NAICS
- 332999
— All Other Miscellaneous Fabricated Metal Product Manufacturing
- Contracting Office
- Department of the Army, U. S. Army Materiel Command, US Army C-E LCMC, Tobyhanna Depot Contracting Office, US Army C-E LCMC, Tobyhanna Depot Contracting Office, ATTN: AMSEL-TY-KO, 11 Hap Arnold Boulevard, Tobyhanna, PA 18466-5100
- ZIP Code
- 18466-5100
- Solicitation Number
- W25G1V-09-R-0022
- Response Due
- 6/23/2009
- Archive Date
- 8/22/2009
- Point of Contact
- JANE ALLARDYCE, (570)895-7645<br />
- E-Mail Address
-
US Army C-E LCMC, Tobyhanna Depot Contracting Office
(jane.allardyce@us.army.mil)
- Small Business Set-Aside
- Total Small Business
- Description
- The purpose of this Amendment 0001 to combined synopsis/solicitation W25G1V-09-R-0022 is to make changes to Drawings A3276908 and A3276910 provided with Attachment(1)to this combined synopsis/solicitation; answer offeror questions received; and extend the offer due date as follows: 1. Drawing A3276908: Change all bend radii of.50 inch. After tolerance 17.750 add: plus/minus.015 2. Drawing A3276910, Notes, Note 2, Delete all bend radius shall be 0.19; Add: All Bend Radius shall be.50 inch. Offeror questions received with the Governments Response: Q1. (a)Drawing A3276908: There are three locations where we are requesting to increase the bend radius to.570 due to the thickness and type of material. The minimum recommended bend radius for this thickness of material should be.570. Also, we are requesting to increase the tolerance on one specific dimension through three bends to plus/minus.015. (b) Drawing A3276910: Same as for Q1(a) (c) I have a question regarding material type on two prints, A3276908 and A3276910: material callout is for 6061-T6, which will crack after bending. Can we quote based on Aluminum 5052-H32, which is softer so bending will not get cracked at the bend line? A1. Bend radii is changed on Drawings A3276908 and A3276910 to read.50 inch. Tolerance of the 17.750 dimension is changed to plus/minus.015. 6061-T6 material must be used. See Drawings A3276908 and A3276910 as changed in Paragraph 1 above. The Offer Due Date is extended: Delete 22 June 2009 @ 4:00 P.M; Add 23 June 2009 @ 4:00 P.M. All other terms and conditions of the solicitation remain the same.
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/USA/USAMC/DAAB17/W25G1V-09-R-0022/listing.html)
- Place of Performance
- Address: US Army C-E LCMC, Tobyhanna Depot Contracting Office ATTN: AMSEL-TY-KO, 11 Hap Arnold Boulevard Tobyhanna PA<br />
- Zip Code: 18466-5100<br />
- Zip Code: 18466-5100<br />
- Record
- SN01846221-W 20090618/090616235652-a8f0f0b3c24f4635ecc8179aa96a2b5d (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |