SOLICITATION NOTICE
30 -- BAR, STRAIN, HOLDBACK ASSEMBLY
- Notice Date
- 3/25/2011
- Notice Type
- Presolicitation
- NAICS
- 333999
— All Other Miscellaneous General Purpose Machinery Manufacturing
- Contracting Office
- Defense Logistics Agency, DLA Acquisition Locations, DLA Land and Maritime, P O Box 3990, Columbus, Ohio, 43218-3990, United States
- ZIP Code
- 43218-3990
- Solicitation Number
- SPM7M2-11-R-0049
- Archive Date
- 5/26/2011
- Point of Contact
- Elizabeth E. Beechey, Phone: 6146927996, JAMES E. DUFFALA, Phone: 614-692-1679
- E-Mail Address
-
elizabeth.beechey@dla.mil, JAMES.DUFFALA@DLA.MIL
(elizabeth.beechey@dla.mil, JAMES.DUFFALA@DLA.MIL)
- Small Business Set-Aside
- N/A
- Description
- BAR, STRAIN, HOLDBACK ASSEMBLY. ****RECEIPT INSPECTION FOR ENTIRE CONTRACT QUANTITY AT NAWC IS MANDATORY********* PCO MANDATORY INSPECTION. DURING PRODUCTION, MANDATORY INSPECTION IS REQUIRED TO BE ACCOMPLISHED AND DOCUMENTED BY THE CONTRACTOR AS FOLLOWS:. CRITICAL AND MAJOR CHARACTERISTICS AS IDENTIFIED IN CLASSIFICATION OF CHARACTERISTICS BLOCK ON DRAWING(S), TECHNICAL SPECIFICATIONS, SECOND TIER DOCUMENTS REFERENCED IN THE ACQUISITION ITEM DESCRIPTION AND SPECIFIED IN THE PROCUREMENT DOCUMENT, AND CHARACTERISTICS DEFINED AS: (A) MATERIAL CERTIFICATIONS (B) DESTRUCTIVE AND / OR NONDESTRUCTIVE TEST RESULTS (WHEN APPLICABLE) (C) ATTRIBUTES FOR PLATING HARDNESS. IMPORTANT MINOR CHARACTERISTICS SHALL BE DEFINED BY THE CONTRACTOR SUBJECT TO QAR CONCURRENCE, UNLESS OTHERWISE DEFINED ON APPLICABLE DRAWING(S), SPECIFICATIONS AND CHARRACTERISTICS DEFINED AS: (A) DIAMETRICAL AND LINEAR DIMENSIONS HAVING A TOLERANCE OF +/- 0.005 INCH OR LESS (B) GEOMETRIC FEATURE CONTROLS HAVING A TOTAL TOLERANCE OF 0.003 INCH OR LESS (C) SURFACE FINISHES HAVING A 16 VALUE OR LESS (D) CLASS THREE THREADS (E) ANGULAR TOLERANCES WITH A TOTAL RANGE LESS THAN 1 DEGREE. LEVEL OF INSPECTION: ANSI / ASQC Z1.4 FOR SINGLE SAMPLING USING A GENERAL INSPECTION LEVEL O II (A) CRITICAL AND MAJOR CHARACTERISTICS: 100% INSPECTION APPLIES (B) IMPORTANT MINOR CHARACTERISTICS: AQL OF 1.5. CERTIFICATION / DATA REPORTS: THE CONTRACTOR IS RESPONSIBLE FOR PREPARING A CERTIFICATE OF QUALITY COMPLIANCE (COQC) IN ACCORDANCE WITH THE DD FORM 1423 CONTRACT DATA REQUIREMENTS LIST (CDRL). THE COQC CONTENT WILL INCLUDE AS A MINIMUM THE DATA DESCRIBED IN DLAR CLAUSE 52.246-9000, IN ADDITION TO ALL PCO MANDATORY INSPECTION RESULTS. THIS COQC REQUIREMENT APPLIES TO EACH UNIT OF CONTRACT QUANTITY. CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. ***** IF AQLS ARE LISTED IN THE SPECIFICATION(S) OR DRAWING(S) THEY MAY BE USED TO ESTABLISH THE AUTHORIZED SAMPLE SIZE,HOWEVER,THE ACCEPTANCE NUMBER FOR THIS CONTRACT IS ZERO;I.E.,THIS CONTRACT REQUIRES A SAMPLING PLAN THAT ACCEPTS ON ZERO DEFECTS AND REJECTS ON ONE OR MORE DEFECT(S). ***** DLAD CLAUSE 52.246-9004,PRODUCT VERIFICATION TESTING,IS HEREBY INCORPORATED,AND MAY BE INVOKED AT THE DISCRETION OF THE PROCUREMENT ACTIVITY. ***** THE INTERNATIONAL ORGANIZATION FOR STANDARDIZATION (ISO) 9002 OR A "TAILORED" PROGRAM MEETING THE FOLLOWING ISO 9002 PARAGRAPHS APPLIES: 4.5, DOCUMENT CONTROL: LIMITED TO INSPECTION AND TESTING AS WELL AS APPLICABLE DRAWINGS, SPECIFICATIONS AND INSTRUCTIONS REQUIRED BY CONTRACT 4.6, PURCHASING: 4.6.1 AND LIMITED TO 4.6.2 A) AND 4.6.4.2, ALL OTHER PARTS OF PARAGRAPH ARE HEREBY DELETED 4.7, CUSTOMER-SUPPLIED PRODUCT: 4.8, PRODUCT IDENTIFICATION & TRACEABILITY: 4.10, INSPECTION & TESTING: 4.11, INSPECTION, MEASURING & TEST EQUIPMENT: 4.12, INSPECTION AND TEST STATUS: 4.13, CONTROL OF NONCONFORMING PRODUCT: 4.14, CORRECTIVE AND PREVENTIVE ACTION: PARAGRAPH 4.14.3 APPLY TO PRODUCT ONLY 4.16, QUALITY RECORDS: FAR CLAUSE 52.246-11 APPLIES ***** DRAWING PACKAGE CITED IS SUBJECT TO EXPORT-CONTROL REGULATIONS AND DISTRIBUTION IS LIMITED TO THOSE CONTRACTORS QUALIFIED THROUGH JCP CERTIFICATION. TO APPLY FOR CERTIFICATION, COMPLETE DD FORM 2345, "MILITARY CRITICAL TECHNICAL DATA AGREEMENT." FORM IS AVAILABLE AT THE WORLD WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO: UNITED STATES/CANADA JOINT CERTIFICATION OFFICE DEFENSE LOGISITICS INFORMATION SERVICE FEDERAL CENTER 74 WASHINGTON AVE,NORTH BATTLE CREEK, MI 49017-3084. CONTRACTS WILL BE AWARDED ONLY TO THOSE CONTRACTORS WITH JCP CERTIFICATION ISSUED PRIOR TO AN AWARD. ***** "ASO/NAVSEA/AVSCOM CRITICAL ITEM" ***** NO DATA IS AVAILABLE. THE ALTERNATE OFFEROR IS REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE INCLUDING DATA FOR THE APPROVED AND ALTERNATE PART FOR EVALUATION. ***** "CERTIFICATE OF QUALITY COMPLIANCE IS MANDATORY" ***** AIRCRAFT LAUNCH AND RECOVERY EQUIPMENT (ALRE). CRITICAL SAFETY ITEM.. ALL REQUESTS FOR WAIVERS OR DEVIATIONS CLASSIFIED AS CRITICAL OR MAJOR MUST BE FORWARDED TO THE DSC CONTRACTING OFFICER FOR REVIEW AND APPROVAL. ALL REQUESTS FOR CLASS I ECPS MUST BE FORWARDED TO THE DSC CONTACTING OFFICER FOR REVIEW AND APPROVAL. ALL REQUESTS FOR WAIVERS OR DEVIATIONS CLASSIFIED AS MINOR SHALL BE DIRECTLY FORWARDED TO NAVAIR LAKEHURST IAW WITH ATTCHED CDRL. ALL REQUESTS FOR CLASS II ECPS SHALL BE DIRETLY FORWARDED TO NAVAIR LAKEHURST IAW ATTACHED CDRL.. ALL ITEMS OF SUPPLY SHALL BE MARKED IAW MIL-STD-129. IN ADDITION, EACH UNIT PACK WILL BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE), CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S CAGE CODE AND PART NUMBER. CRITICAL APPLICATION ITEM GE AVIATION SYSTEMS LLC (97415) P/N 7-0529-1 I/A/W DRAWING NR 16236 CN-01-116-8562 REFNO AMEND NR B DTD 09 SEP 09 TYPE NUMBER: I/A/W DRAWING NR 97415 7-0529 REFNO AMEND NR H DTD 94 JUL 14 TYPE NUMBER: 7-0529-1 Quantity (including option quantity): 36 Unit of Issue: EA Destination Information: Inspection and acceptance at origin, FOB destination, Receipt Certification Inspection. Delivery Schedule: 424 days All responsible sources may submit an offer/quote which shall be considered. One or more of the items under this acquisition may be subject to an Agreement on Government Procurement approved and implemented in the United States by the Trade Agreements Act of 1979. All offers shall be in the English language and in U.S. dollars. All interested suppliers may submit an offer. Based upon market research, the Government is not using the policies contained in Part 12, Acquisition of Commercial Items, in its solicitation for the described supplies or services. However, interested persons may identify to the contracting officer their interest and capability to satisfy the Government's requirement with a commercial item within 15 days of this notice. The solicitation will be available in FedBizOpps on its issue date of 4/11/11. The Small Business size standard is 500 employees. Specifications, plans or drawings are not available. This acquisition is for supplies for which the Government does not possess complete, unrestrictive technical data; therefore, the Government intends to solicit and contract with only approved sources under the authority of 10 U.S.C. 2304(c)(1). Approved sources are: CAGE 97415. While price may be a significant factor in the evaluation of offers, the final award decision will be based upon a combination of price, delivery, past performance and other evaluation factors as described in the solicitation.
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DLA/J3/DSCC/SPM7M2-11-R-0049/listing.html)
- Record
- SN02409907-W 20110327/110325234910-abc5c6809934a419a9d123d154c76773 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |