SOLICITATION NOTICE
28 -- NOZZLE,TURBINE,AIRC, AMC 3Z, 305-350-150-0, NSN2840-01-344-9157
- Notice Date
- 4/20/2011
- Notice Type
- Presolicitation
- NAICS
- 336412
— Aircraft Engine and Engine Parts Manufacturing
- Contracting Office
- DEFENSE LOGISTICS AGENCY; DLR PROCUREMENT OPS DSCR-ZBA;3001STAFF DRIVE; TINKER AFB; OK; 73145
- ZIP Code
- 73145
- Solicitation Number
- SPRTA1-11-Q-0364-0001
- Response Due
- 3/17/2011
- Point of Contact
- Deborah Teubert, Phone 405-734-8107, Fax - -, Emaildeborah.teubert@tinker.af.mil
- E-Mail Address
-
Deborah Teubert
(deborah.teubert@tinker.af.mil)
- Small Business Set-Aside
- N/A
- Description
- The purpose of this amendment is to incorporate surplus materialrequirements into Solicitation SPRTA1-11-Q-0364 as follows: FIRST: Surplus material requirements are as follows: Acceptable New and Unused Surplus Material: (formerly 9952.211-9006)Surplus material shall be new/unused material and acceptance inspectionshall be conducted at contractor's facility by DCMA/QAR, Commercial offthe shelf (COTS) surplus parts, supplied by surplus vendor shall havethe original FAA Form 8130-3 or Certificate of Conformance withappropriate documentation annotated by the OEM's manufacturing source.An incomplete, altered or incorrect FAA 8130-3 and/or Certificate ofConformance is unacceptable as an Airworthiness Release Record. Asurplus vendor is a supplier not the manufacture of subject part andcannot verify part meets FAA design and Airworthiness standards. No commercially repaired, reconditioned or modified surplus COTSmaterial will be authorized and/or acceptable for use in MilitaryF108-CFM56-2B engines. No FAA-PMA manufactured new/unused replacementparts that were approved for production under these methods, FAAdesignees; DER, DOA, DAS is allowed unless specifically approved SARpackage or OC-ALC/GKGBAB Engineering approval prior to acceptanceinspection. PMA P/Ns are identified with either prefix/suffix todifferentiate from OEM P/N and are not acceptable without priorapproval. ATA Spec 106 is not an FAA acceptable form for surplusmaterial. Item No(s) 0002 Part Number Verification: (formerly 9952.211-9011)Items must be of the correct part number, (*), and must have beenmanufactured by (**). Item No(s)*Part Number**Manufacturer 0002305-350-150-058828 Prior Government Ownership of Items: (formerly 9952.211-9016)Items that were previously owned by the Government must be evidenced bythe item marking contained on the original shipping containers ornameplate. Item No(s) 0002 100 Percent End Item Inspection: (formerly 9952.211-9017)100 Percent End Item Inspection is required. New Manufactured Material And Government Or Commercial Surplus MaterialAcceptable: (formerly 9952.211-9005)New manufactured as defined as well as Government surplus or commercialsurplus material as defined as (1) material, including commercialoff-the shelf items manufactured for either Government or commercial use(e.g. production overrun quantities), which has never been sold to oraccepted by the Government; or (2) material which would be considered"new Manufactured" except that it is not held by the actualmanufacturer, the system contractor or subsidiary, successor, ordistributor and as indicated below, will be considered to be acceptablein satisfaction of this requirement. The categories of surplus materialand the Contract Line Item(s) to which this statement applies are:Verifiable Dimensions: (formerly 9952.211-9012)Items furnished must meet all dimensions, which are verifiable withoutdisassembly: Item No(s)Manufacturer NameDrawing Number 000258828305-350-150-0 Initial Acceptability Items: (formerly 9952.211-9014The Initial Acceptability Items (IAIs) shall be inspected to determineif they comply with all verifiable dimensional and material requirementsfor the items identified below. If acceptable, the IAIs shall bereturned to the Contract Administration Office to be used to inspect theremaining items. This statement applies to Item No(s) Not applicable New Manufactured Material: (formerly 9952.211-9002) New material means material manufactured by a qualified manufacturer,which has a Government-approved in-process quality system meeting therequirements of this solicitation. Previously manufactured material isconsidered "new material" as long as it in new and unused and held bythe actual manufacturer, the system contractor or subsidiary, successoror distributor. This solicitation does not contemplate surplus material.In the event surplus material is offered and it is determined to be thebest value to the Government, a determination shall be made as to itsacceptability. The urgency of the instant action and the time necessaryfor evaluation may preclude consideration of surplus material for thisaward, however; in the event surplus material is determined to beacceptable, the solicitation will be amended announcing any supplementalinspection requirements and revising the due date for receipt ofproposals. This statement applies to Item No(s) 0001, 0002 Listing Of Surplus Material: (formerly 9952.211-9018) Submission of the following information for each item of surplusmaterial included in the offeror's proposal is required to comply withthe terms and conditions of FAR 11.302 (b). Information must be adequateto provide the basis for determinations required by the policy containedin FAR 11.302(b).(a) Surplus Item Identification: _______________NSN: _______________Noun: ____________PN: ____________Drawing Revision Letter: ____________ Manufacturer: ____________(b) Federal Supply Code for Manufacturer (FSCM) marked on items perMIL-STD-130: ____________(c) Quantity available for verification at dealer's facility:____________(d) Original manufacturer, government contract number: ____________(e) Material was subsequently purchased as surplus from: ____________(Manufacturer or Agency)(f) DLA sale number ____________ and date of sale by Government:____________(g) Do you have the drawings for this item? If yes, what is the revisionletter/number and the date of the last revision of the drawings?____________(h) History of items since initially sold as surplus by Government ormanufacturer: _____________________(Storage Location, Packaging, Rework, Reconditioning, Repair, etc.)(i) Are items being offered in original unbroken containers?____________(j) Date of manufacture or packaging: _______________(k) Material offered is warranted by the Contractor for a period of ____months as contemplated by FAR 52.246-17, Warranty of Supplies of aNoncomplex Nature. (12 Months is presumed unless otherwise specified. Ifsurplus is purchased, warranty may or may not be included in the award.)(l) The surplus items offered fit the conditional definition indicatedbelow: (Check the appropriate definition and provide requestedinformation. Use additional paper if more space is necessary.) (NOTE:Dates, Technical Order compliance, quality considerations, and componentsources are essential information for categories (2), (3), and (4)below.) [ ] (1) New and unused: material has never been installed or used. Itshows no signs of rust, corrosion, or other deterioration due to age orimproper packaging/preservation. It has not been reconditioned and showsno evidence of disassembly or reassembly.[ ] (2) New and reconditioned: material has never been installed orused. It shows no signs of rust, corrosion, or other deterioration dueto age or improper packaging/preservation. Reconditioning is allowed tothe extent that gaskets, seals, O-rings, or other such cure-dated itemshave been or will be replaced prior to use in accordance with theapplicable technical orders and specifications.Source of reconditioning: ____________Summary of reconditioning: ____________[ ] (3) New and modified: material has never been installed or used. Itshows no signs of rust, corrosion, or other deterioration due to age orimproper packaging/preservation. Components may have been (or may needto be) replaced in accordance with the applicable technicalspecifications for the purpose of configuration update or modification.Source of modification: ____________Summary of modification: ____________[ ] (4) Used and overhauled: material, which has been previouslyinstalled in operational equipment. It has been or can be completelyoverhauled, repaired, reconditioned, or modified per the applicabletechnical specifications to serviceable status.Source of overhaul: ____________Overhaul technical order: ____________ (Applicable when contemplating acquisition of surplus material) SECOND: All other terms and conditions remain unchanged and in fullforce.
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/USAF/AFMC/OCALCCC/SPRTA1-11-Q-0364-0001/listing.html)
- Record
- SN02429018-W 20110422/110420235014-55bc22aa7eb91040dd7279b60d642079 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |