PRESOL | U | PURCHASE OF TRAINING SERVICES

FBO DAILY ISSUE OF JUNE 04, 2011 FBO #3479
SOLICITATION NOTICE

U -- PURCHASE OF TRAINING SERVICES

Notice Date: 6/2/2011
Notice Type: Combined Synopsis/Solicitation
NAICS: 611710 — Educational Support Services
Contracting Office: Department of Homeland Security, United States Coast Guard (USCG), Commanding Officer (C2CEN), USCG Command and Control Engineering Center, 4000 Coast Guard Boulevard, Portsmouth, Virginia, 23703-2199, United States
ZIP Code: 23703-2199
Solicitation Number: HSCG44-11-Q-PC7185
Archive Date: 6/23/2011
Point of Contact: James A Lassiter, Phone: (757)686-2149
E-Mail Address: james.a.lassiter@uscg.mil
(james.a.lassiter@uscg.mil)
Small Business Set-Aside: N/A
Description: Description: This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6 as supplement with additional information in this notice. This announcement constitutes the ONLY solicitation and no other solicitation document will be issued. This solicitation is issued as a Request For Quote number RFQ HSCG44-11-Q-PC7185. This number is for tracking purposes only. Solicitation documents and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 05-51. This procurement will be processed in accordance with FAR Part 12 and 13. The North American Industry Classification System (NAICS) is 611710. The SBA size standard is $7.0 Million. Due to this Acquisition being considered to be a Sole Source Procurement it is not anticipated that the Contracting Officer will receive 2 or more Offers from qualified Small Business Concerns; therefore IAW FAR 19.502-2(a), This IS NOT A Small Business Set-A-Side. The USCG Command, Control and Communications Engineering Center (C3CEN) Portsmouth, VA. 23703, intends to purchase on a non-competitive basis by awarding a Firm Fixed Purchase Order Contract to: AMSEC, LLC for training for Cableway Improvement Program (CIP). The proposed contract action resulting from this synopsis/solicitation for commercial services is the Government's intention to solicit and negotiate with only one source under the authority of FAR 6.302.1 and 13.106-1(b). Interested persons/parties may indentify their interest and capability to respond to the requirement or submit proposals. This notice of intent is not a request for competitive proposals. However, all proposals received within 5 days after date of publication of this synopsis/solicitation will be considered by the Government. A determination by the Government not to compete with this proposed contract based upon responses to this notice is solely within the discretion of the Government. Information received will normally be considered solely for the purpose of determining whether to conduct a competitive procurement, and for informational purposes. The contractor for this proposed Sole Source contract is: AMSEC, LLC, Cage Code 1LT84. A current CCR Data Search and EPLS Data Search was conducted on this Contractor by the Contracting Officer. This Contractor is current/active in CCR and does not appear on the EPLS List. Data Search date: JUN/01/2011. This is a Sole Source Procurement. See attached JOTFOC Document below. The government intends to award a contract resulting from this solicitation to the responsible bidder proposal conforming to the solicitation which will be most advantageous and Best Value to the Government, price and other factors considered. The Required Delivery Dates are specified in Schedule B below. FIRM FIXED Price Proposals may be submitted on company letterhead stationary and must include the following information: Cost Breakdown, Unit Price, Extended Price, Payment Terms and discount offered for prompt payment. The closing date and time for receipt of offers is JUN/08/2011@7:00AM EST. Facsimile and Email quotes are acceptable and may be faxed to (757) 686-4018 or Emailed to the POC James A. Lassiter, Contracting Officer, james.a.lassiter@uscg.mil. *PLEASE NOTE* Interested Offerors are to provide Firm Fixed Prices and Delivery Information by JUN/08/2011@7:00AM EST. Delivery Information is to include the Shipping Terms the Offeror is proposing, FOB Origin or FOB Destination. Destination is preferred by USCG/GOV. If proposing FOB Origin, provide Shipping cost as a separate line item. Required Delivery Date are specified in schedule B below. Anticipated Award Date for the PO Contract is NLT than JUN/10/2011, this date is approximate and not exact. Schedule B: All Training is to be provided IAW the Statement of Work, below. Line 1: 1 each 5-day Shipboard Cable Installation and Inspection Training session for 20 participants. Training is held at USCG facilities in Mayport, FL at a time to be determined prior to October 31, 2011. This includes travel, shipping of materials for the class, class materials, and labor. Line 2: 1 each 5-day Shipboard Cable Installation and Inspection Training session for 20 participants. Training is held at USCG facilities in Cleveland, OH from 25 to 29 July 2011. This includes travel, shipping of materials for the class, class materials, and labor. Line 3: 1 each 5-day Shipboard Cable Installation and Inspection Training session for 20 participants. Training is held at USCG facilities in Baltimore, MD August 1-5, 2011. This includes travel, shipping of materials for the class, class materials, and labor. Line 4: 1 each 5-day Shipboard Cable Installation and Inspection Training session for 20 participants. Training is held at USCG facilities in Honolulu, HI July 11-15, 2011. This includes travel, shipping of materials for the class, class materials, and labor. Line 5: 1 each 5-day Shipboard Cable Installation and Inspection Training session for 20 participants. Training is held at USCG facilities in Kodiak, AK August 22-26, 2011. This includes travel, shipping of materials for the class, class materials, and labor. Line 6: 1 each 5-day Shipboard Cable Installation and Inspection Training session for 20 participants. Training is held at USCG facilities in Miami, FL August 8-12, 2011. This includes travel, shipping of materials for the class, class materials, and labor. Line 7: 1 each 5-day Shipboard Cable Installation and Inspection Training session for 20 participants. Training is held at USCG facilities in New Orleans, LA June 13-17, 2011. This includes travel, shipping of materials for the class, class materials, and labor. Line 8: 1 each 5-Day shipboard cable installation and inspection training session for 20 participants. Training is held at local AMSEC facilities in Virginia Beach at a time to be determined prior to December 31, 2011. The Following FAR Provisions apply to this Acquisition: FAR 52.212-1 Instructions to Offerors FAR 52.212-2 Evaluation-Commercial Items (a) Overall Best Value to the Government FAR 52.212-3 Offeror Representations and Certifications-Commercial Items, Offerors should be registered in CCR The Following FAR Clauses apply to this Acquisition: FAR 52.212-4 Contract Terms and Conditions-Commercial Items FAR 52.212-5 Contract Terms and Conditions Required to Implement Statutes or Executive Orders-Commercial Items The government intends to award a Purchase Order Contract resulting from this solicitation to the responsible bidder/offeror quotation conforming to the solicitation which will be most advantageous and Overall BEST VALUE to the Government, price and other factors considered. FAR 52.212-1 Instructions to Offerors-Commercial Items (JUN 2008), FAR 52.212-2 Evaluation-Commercial Items (JAN 1999)- award will be made to the Offeror proposing the Best Value to the Government considering specification,price, delivery, and past performance, and quality. FAR 52.212-3 Offeror Representations and Certifications-Commercial Items (JAN 2011) to include Alt I (APR 2002). These certifications must be included with quote and can be accessed and downloaded via FedBizOps with this RFQ. Contractors are encouraged to submit through http://orca.bpn.gov FAR 52.212-4 Contract Terms and Conditions -Commercial Items (JUNE 2010) with the following addendas: FAR 52.252-2 Clauses Incorporated by Reference (FEB 1998), the full text of the clause may be accessed electronically at Internet address http://www.arnet.gov/far; A Data Universal Numbering System (DUNS) Number is the primary identifier in FAR 52.204-7 Central Contractor Registration (CCR)(Jul 2006). Contractors are located and identified in CCR by their DUNS number. To facilitate payment via Electronic Funds Transfer - CCR, contractors should be registered in the CCR. A DUNS Number can be obtained via www.dnb.com and CCR registration can be obtained via www.ccr.dlis.dla.mil FAR 52.212-5, Contract Terms and Conditions to Implement Statutes or Executive Orders Commercial Items (JAN 2011), The following Clauses and others as indicated by the Contracting Officer as applicable shall apply to the awarded contract. FAR 52.222-50 Combating Trafficking in Persons (FEB 2009) FAR 52.233-3 Protest After Award (AUG 1996) FAR 52.233-4 Applicable Law for Breach of Contract Claim (OCT 2004) FAR 52.222-3 Convict Labor (June 2003) FAR 52.222-19 Child Labor-Cooperation with Authorities and Remedies (AUG 2009) (E.O. 13126),; FAR 52.222-21 Prohibition of Segregated Facilities (FEB 1999) FAR 52.222-26 Equal Opportunity (MAR 2007)(E.O. 11246), FAR 52.222-35 Equal Opportunity for Special Disable Veterans, Veterans of the Vietnam Era, and Other Eligible Veterans (SEPT 2006) (38 U.S.C. 4212), FAR 52.222-36 Affirmative Action for Workers with Disabilities (JUN 1998)(29 U.S.C. 793), FAR 52.222-37 Employment Reports on Special Disabled Veterans and Veterans of the Vietnam Era, and Other Eligible Veterans (SEPT 2006)(38 U.S.C. 4212), FAR 52.223-18 Contractor Policy to Ban Text Messaging While Driving (SEPT 2010) FAR 52.225-1 Buy American Act-Supplies (FEB 2009) FAR 52.225-13 Restrictions on Certain Foreign Purchases (JUN 2008)(E.O. 12722,12724,13059.13067,13121, and 13129) FAR52.232-33 Payment by Electronic Funds Transfer-Central Contractor Registration (OCT 2003)(31 U.S.C. 3332) The above/following clauses are incorporated by reference, entire clause(s) available at http://www.arnet.gov/far; NOTICE TO OFFERORS CONCERNING REPRESENTATIONS AND CERTIFICATIONS: This solicitation contains FAR Clause 52.204-7, Central Contractor Registration and FAR Provision 52.204-8, Annual Representations and Certifications. In accordance with FAR 4.1201 prospective contractors are required to submit annual representations and certifications via the Online Representations and Certifications Application (ORCA) at http://orca.bpn.gov. Please ensure completion prior to submission of your quote. Also note that paragraph (b) of FAR 52.204-8, applies. JUSTIFICATION FOR OTHER THAN FULL AND OPEN COMPETITION (JOTFOC) (a) Each justification shall contain sufficient facts and rationale to justify the use of the specific authority cited. As a minimum, each justification shall include the following information: (1) Identification of the agency and the contracting activity, and specific identification of the document as a "Justification for other than full and open competition." USCG C3CEN Core Technologies, Command & Control Support Section (CT-C2) located in Portsmouth, VA. (2) Nature and/or description of the action being approved. NAVSEA Cableway Training & Certification Course, certification program for twenty persons on the topic of the installation and inspection of shipboard cable. Training is broken down into classroom sessions and hands-on test at the end. Students who pass the class are certified by AMSEC LLC as Cable installation inspectors. Duration of the class is five days and is held at USCG facilities in various locations in the United States and the AMSEC Facility in Virginia Beach, VA. (3) A description of the supplies or services required to meet the agency's needs The Type-B Certifications program inspects all electronics installations according to numerous NAVSEA installation requirements, with an emphasis on NAVSEAINST 9304.1D (Shipboard Electrical Cable and Cableway Inspection and Reporting Procedures) and DOD-STD-2003 NAVY EPISM (Electrical Plant Installation Standards Method). The NAVSEA Cableway course is a requirement for Type-B Certification Inspectors, and as such, is an important training tool for the fleet to meet required NAVY and DOD installation standards. Estimated value $8.000 for a 5-Day Training for up to 20 Students in at AMSEC LLC: Located at 2829 Guardian Lane, Virginia Beach, VA 23452. (4) An identification of the statutory authority permitting other than full and open competition. Commander, Naval Sea Systems Command (NAVSEA), U.S. Department of the Navy has the statutory authority 6.302-1 (2)(ii) Only one responsible source and no other supplies or services will satisfy agency requirements. 2) When the supplies or services required by the agency are available from only one responsible source, or, for DoD, NASA, and the Coast Guard, from only one or a limited number of responsible sources, and no other type of supplies or services will satisfy agency requirements, full and open competition need not be provided for. (5) A demonstration that the proposed contractor's unique qualifications or the nature of the acquisition requires use of the authority cited. Since 1996, AMSEC LLC (formerly SAIC AMSEC) has been acknowledged by the U.S. Navy as the sole authorized NAVSEA instructor for training personnel for the installation and inspection of shipboard cables in accordance with NAVSEAINST 9304.1C (Shipboard Electrical Cable and Cableway Inspection and Reporting Procedures), and DOD-STD-2003 NAVY EPISM (Electrical Plant Installation Standards Method). (6) A description of efforts made to ensure that offers are solicited from as many potential sources as is practicable, including whether a notice was or will be publicized as required by Subpart 5.2 and, if not, which exception under 5.202 applies. - This requirement will be posted to Fed-Biz-Ops with the statement that any offerors that feel that they can meet the requirement may provide quotations/proposals. (7) A determination by the contracting officer that the anticipated cost to the Government will be fair and reasonable. The offered price is the same that the General Public would pay for this same 5-Day Training Session. This Training is available to the General Public as stated by the Contractor AMSEC. (8) A description of the market research conducted (see Part 10) and the results or a statement of the reason market research was not conducted. A search using the World Wide Web was conducted, and that search confirmed that no other sources are known by the Government to conduct this specialized training. (9) Any other facts supporting the use of other than full and open competition, such as: (i) Explanation of why technical data packages, specifications, engineering descriptions, statements of work, or purchase descriptions suitable for full and open competition have not been developed or are not available. N/A (ii) When 6.302-1 is cited for follow-on acquisitions as described in 6.302-1(a)(2)(ii), an estimate of the cost to the Government that would be duplicated and how the estimate was derived. tiny_mce_marker_________________________ (iii) When 6.302-2 is cited, data, estimated cost, or other rationale as to the extent and nature of the harm to the Government. This special Training is certified thru the US Naval Sea Systems Command, it would not be feasible or practical for the Navy to certify another Contractor to conduct this specialized training. Ref NAVSEAINST 9304.1C and letter From: the Commander Naval Systems Command (10) A listing of the sources, if any, that expressed, in writing, an interest in the acquisition. None at this time. (11) A statement of the actions, if any, the agency may take to remove or overcome any barriers to competition before any subsequent acquisition for the supplies or services required. None at this time. (12) Contracting officer certification that the justification is accurate and complete to the best of the contracting officer's knowledge and belief. (b) Each justification shall include evidence that any supporting data that is the responsibility of technical or requirements personnel (e.g., verifying the Government's minimum needs or schedule requirements or other rationale for other than full and open competition) and which form a basis for the justification have been certified as complete and accurate by the technical or requirements personnel. Contracting Officer: Jim Lassiter Technical POC: ETC Mark Chaney 25-MAY-11 Statement of Work for NAVSEA Cableway Training & Certification Course Prepared by United States Coast Guard Command, Control, and Communications Engineering Center SHORT TITLE: Shipboard Electrical Cable and Cableway Inspection and Reporting Procedures Start Date: As directed End Date: All Training Classes shall be completed within 1 yr of Contract Award Date. 1. PLACE(S) OF PERFORMANCE: 1.1. Places of Performance shall be but not limited to USCG's Facilities at: 1.1.1. Baltimore, MD 1.1.2. Cleveland, OH 1.1.3. Honolulu, HI 1.1.4. Kodiak, AK 1.1.5. Mayport, FL 1.1.6. Miami, FL 1.1.7. New Orleans, LA 1.1.8. Virginia Beach, VA 2. REFERENCES: 2.1. COMFLTFORCOMINST 4790.3(Series) - Joint Fleet Maintenance Manual (JFMM) 2.2. DOD-STD-2003 - Military, Standard, Electric Plant Installation Standard Methods for Surface Ships and Submarines 2.3 NAVSEAINST 9304.1(Series) - Shipboard Electrical Cable and Cableway Inspection and Reporting Procedures 3. SPECIFICATIONS: N/A 4. SECURITY REQUIREMENTS: 4.1. AMSEC shall provide a list of, and as required appropriate security clearance information for each instructor to each facilities' Security Officer and local Point of Contacts an minimum three (3) days prior to arrival at training location. 4.2. Each AMSEC instructor shall provide government issued identification verifying the instructor's identity upon arrival at training location. 4.3. Each student shall provide government issued identification verifying the student's identity. 5. TASK ORDER MANAGEMENT DESIGNATION: 5.1. The Contracting Officer for this work order is: James Lassiter who can be reached at 757.686.2149, E-Mail address: james.a.lassiter@uscg.mil 6. DESCRIPTION OF WORK: 6.1. Scope: 6.1.1. The Contractor shall provide Eight (8) five (5) day course of instruction detailing the proper Shipboard Electrical Cable and Cableway Inspection and Reporting Procedures for up to Twenty (20) students each class. 6.1.2. The instruction shall be held at USCG facilities around the country and the AMSEC facility in Virginia Beach, VA. 6.1.3. The instructor shall provide instruction for each student so that they are completely familiar with inspection and reporting procedures IAW NAVSEAINST 9304.1(Series). 6.1.4. The goal is to provide cable installers, pullers, repair personnel and inspectors training in proper cable removal and installation procedures. 6.2. Background: 6.2.1. The Type-B Certifications program inspects all electronics installations according to numerous NAVSEA installation requirements, with an emphasis on NAVSEAINST 9304.1D (Shipboard Electrical Cable and Cableway Inspection and Reporting Procedures) and DOD-STD-2003 NAVY EPISM (Electrical Plant Installation Standards Method). 6.2.2. The NAVSEA Cableway course is a requirement for Type-B Certification Inspectors, and as such, is an important training tool for the fleet to meet required NAVY, Coast Guard, and DOD installation standards. 6.3. Requirements: 6.3.1.1. The following is a list of objectives that shall be met during the training. 6.3.1.1.1. OVERVIEW / INTRODUCTION: 6.3.1.1.1.1. The Instructor shall give the student an introduction to shipboard cable hazards and provides examples of existing and potential problems in electrical cables and cableways. 6.3.1.1.2. SPECIAL TOOLS AND EQUIPMENT: 6.3.1.1.2.1. The Instructor shall present the various tools and equipment and their use that will be required to properly remove dead end cable, install new cables and make repairs to disturbed cableways and equipment. 6.3.1.1.2.2. TERMINAL OBJECTIVE: 6.3.1.1.2.2.1. Students given the appropriate electrical tools and equipment, demonstrate their proper use in accordance with the guidelines specified in Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.2.3. ENABLING OBJECTIVES: 6.3.1.1.2.3.1. Students given a list of tools and their uses, match each tool with its appropriate use in accordance with the guidelines specified in Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.3. STUFFING TUBES: 6.3.1.1.3.1. The Instructor shall present the types, parts, proper installation and proper packing procedures for metal stuffing tubes. 6.3.1.1.3.2. TERMINAL OBJECTIVES: 6.3.1.1.3.2.1. Students are given an assignment to plan the installation of metal stuffing tubes to run electrical cables through a bulkhead or deck, sketch a layout plan showing proper tube sizes, hole dimensions, and spacing between adjacent tubes. The plan must be in accordance with the guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.3.2.2. Students are to pack a metal stuffing tube in accordance with the guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM, using the proper tools and materials. 6.3.1.1.3.3. ENABLING OBJECTIVES: 6.3.1.1.3.3.1. Students are given drawings of different types of metal stuffing tubes, name each type. 6.3.1.1.3.3.2. Students are provided with a list of different size cables and a cable assignment chart, select the correct stuffing tube size for each cable. 6.3.1.1.3.3.3. Students are provided with a list of different stuffing tube sizes and a tube spacing chart, select the proper tube dimension for each stuffing tube mounting hole. 6.3.1.1.3.3.4. Students are given a list of stuffing tube sizes select the correct packing and metal tube blank for each tube. 6.3.1.1.3.3.5. Students are given a list of stuffing tube sizes and a hole spacing chart, determine the spacing required between adjacent tubes. 6.3.1.1.3.3.6. Students are given a list of stuffing tube sizes, a hole spacing chart, and a ruler, sketch a layout for the installation of the listed tubes. 6.3.1.1.4. PENETRATION OF EQUIPMENT AND CONNECTION BOXES: 6.3.1.1.4.1. The Instructor shall present information that will help personnel select and install watertight and non-watertight connectors penetrating equipment and seal holes in equipment when unused cables are removed. 6.3.1.1.4.2. TERMINAL OBJECTIVE: 6.3.1.1.4.2.1. Students are given cables and a cable assignment chart to determine the size of nylon stuffing tube, nylon tube packing assembly, metal terminal tube or the correct size box connector required. 6.3.1.1.4.2.2. Students are given tools and material to remove dead ended cable from equipment and seal all unused penetrations in accordance with guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.4.3. ENABLING OBJECTIVES: 6.3.1.1.4.3.1. Students are given illustrations of cable penetrating pieces of equipment, determine if they are watertight or non-watertight. 6.3.1.1.4.3.2. Students match the types of connectors with statements that best describe their uses. 6.3.1.1.4.3.3. Students are given an illustration of a nylon stuffing tube, label each part. 6.3.1.1.4.3.4. Students are given a list of different size cables and box connectors, determine the size plug required for the hole. 6.3.1.1.4.3.5. Students are given a list of different size cables and nylon stuffing tubes, determine the size plug required to seal the nylon stuffing tubes. 6.3.1.1.4.3.6. Students are given a list of different size cables and metal terminal tubes, determine the size plug required to seal the metal terminal tubes. 6.3.1.1.4.3.7. Students are given a list of different size cables and a cable assignment chart for box connectors, determine the size connector and clearance hole size. 6.3.1.1.4.3.8. Students are given a list of different size cables and a cable assignment chart for nylon stuffing tubes, determine the size connector, clearance hole size and packing assembly for each cable. 6.3.1.1.4.3.9. Students are given a list of different size cables and a cable assignment chart for metal stuffing tubes, determine the size of tube and size of cable clearance hole. 6.3.1.1.4.3.10. Students are given a list of steps required to install a metal stuffing tube in a piece of equipment or connection box, arrange the steps in a sequence. 6.3.1.1.5. MULTICABLE PENETRATORS: 6.3.1.1.5.1. The Instructor shall present the various types of multicable, penetrators, (MCP's), their component parts, and application. 6.3.1.1.5.2. TERMINAL OBJECTIVES: 6.3.1.1.5.2.1. Students are given the task to plan a Multicable Penetrator (MCP) installation for running cables through a watertight bulkhead, sketch a layout on a multicable penetrator grid showing the numbers and types of installation blocks to use in accordance with guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.5.2.2. Students are given the proper tools and equipment and a completed MCP grid, pack a multicable penetrator in accordance with guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.5.3. ENABLING OBJECTIVES: 6.3.1.1.5.3.1. Students are given expanded drawings of MCP's, label each part. 6.3.1.1.5.3.2. Students are to match the parts of the multicable penetrator to the statement that best describes its function. 6.3.1.1.5.3.3. Students are given three groups of cable types to be installed in a bulkhead, select the proper MCP to use for each group. 6.3.1.1.5.3.4. Students are given a group of unidentified cables, and must determine the proper MCP block for each. 6.3.1.1.5.3.5. Students are given a list of different size cables and a Cable Assignment Chart, select the correct insert blocks for each cable type. 6.3.1.1.5.3.6. Students are given a Multicable Penetrator Grid, Multicable Penetrator Cable Assignment Chart, and a list of cable types, sketch a layout of the MCP. The MCP installation plan must be in accordance with guidelines specified in the Electric Plant Installation Standard Methods DOD-STD--2003 (NAVY) EPISM. 6.3.1.1.5.3.7. Students discuss the application of the ROX system 6.3.1.1.5.3.8. Students discuss the application of the Brattberg system 6.3.1.1.5.3.9. Students are given discuss the application of the RISE system. 6.3.1.1.6. HANGERS: 6.3.1.1.6.1. The Instructor shall present the different types and sizes of cable hangers and their application. 6.3.1.1.6.2. TERMINAL OBJECTIVES: 6.3.1.1.6.2.1. Students illustrate a single and multiple cable runs, plan the installation of hangers. The plan must show at a minimum the proper placement of the first hanger, proper bend radius, and spacing between each hanger. The plan must be in accordance with guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.6.3. ENABLING OBJECTIVES: 6.3.1.1.6.3.1. Students are given illustrations of hangers, write the name of each type. 6.3.1.1.6.3.2. Students match the proper type of hanger with statements that best describe its uses. 6.3.1.1.6.3.3. Students are provided with situations requiring the use of hangers, select the appropriate type(s). 6.3.1.1.6.3.4. Students are given illustrations of hangers that have been installed for a cableway, calculate the proper spacing for the first hanger, proper bend radius and proper spacing between each hanger. 6.3.1.1.7. BANDING: 6.3.1.1.7.1. The Instructor shall present the banding tool, special equipment, and materials that are required to properly band cables in cableways. 6.3.1.1.7.2. TERMINAL OBJECTIVE: 6.3.1.1.7.2.1. Students are given cable runs, banding tools, equipment and materials, to band cable runs in accordance with guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.7.3. ENABLING OBJECTIVES: 6.3.1.1.7.3.1. Students are given list of places where cables must be banded to hangers in a cableway. 6.3.1.1.7.3.2. Students are given statements describing the placement and banding of cables to hangers, select the proper arrangement. 6.3.1.1.7.3.3. Students are given a list of different size banding, select the ones to be used for banding cable runs in accordance with guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.7.3.4. Students are given a list of cable runs, select which runs should be banded with a buckle and band assembly or with a hose clamp. 6.3.1.1.7.3.5. Students are given banding materials, proper tools and equipment, fabricate a buckle and band assembly. 6.3.1.1.7.3.6. Students are given cable-banding situations, the proper tools and equipment, secure the cables to the hangers with the proper banding materials. 6.3.1.1.8. CHAFING RINGS: 6.3.1.1.8.1. The Instructor shall present the purpose of chafing rings and the methods of determining whether additional cable can be passed through existing chafing rings. 6.3.1.1.8.2. TERMINAL OBJECTIVES: 6.3.1.1.8.2.1. Students are given a description of cables/cableway passing through a non¬-watertight bulkhead, to determine if additional cable can be passed through the existing chafing ring in accordance with guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.8.2.2. Students are given a description of cables to be passed through a non-watertight fire zone boundary bulkhead, to determine if it is packed in accordance with guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM, to make the passage a fire-tight and fume-tight boundary. 6.3.1.1.8.2.3. Students are given a description of cables to be passed through a non-watertight bulkhead, to design a chafing ring to accommodate each cable; allow for 20 percent unfilled space for future cable additions; and maintain a minimum clearance space around cables 1/4 inch for single cables and 1 inch for multiple cables in accordance with guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.8.3. ENABLING OBJECTIVES: 6.3.1.1.8.3.1. Students are given a description of cables/cableway passing through a non-watertight bulkhead, determine if additional cable can be passed throughthe existing chafing ring. 6.3.1.1.8.3.2. Students are given a description of cables to be passed through a non-watertight fire zone boundary bulkhead, determine if it is packed to make the passage a fire-tight and fume-tight boundary. 6.3.1.1.9. DEAD ENDING CABLES: 6.3.1.1.9.1. The Instructor shall present various end sealing methods, selection of proper end caps for each conductor and cable, and end sealing procedures. 6.3.1.1.9.2. TERMINAL OBJECTIVES: 6.3.1.1.9.2.1. Students are given an end cap chart and the proper tools and equipment, to end seal a dead-ended cable in accordance with the guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.9.3. ENABLING OBJECTIVES: 6.3.1.1.9.3.1. Students are given different cable types and a copy of the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM, select the method for end sealing dead-ended cables. 6.3.1.1.9.3.2. Students are given pieces of different cable types, an end cap chart, ruler, wire gage, and an AWG & C/M Cross Reference Chart, select the proper end caps for each conductor and cable. 6.3.1.1.9.3.3. Students are given a piece of cable, proper end caps, and a heat gun, seal the end caps to conform to the diameter of the conductor. 6.3.1.1.10. SPLICING CABLES: 6.3.1.1.10.1. The Instructor shall present the basic splicing materials and proper procedures for splicing armored and unarmored cables used in power, control, and communication systems. 6.3.1.1.10.2. TERMINAL OBJECTIVE: 6.3.1.1.10.2.1. Students given the proper tools and supplies, splice an electrical cable in accordance with the guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.10.3. ENABLING OBJECTIVES: 6.3.1.1.10.3.1. Students are given proper tools and supplies, prepare cable ends for splicing. 6.3.1.1.10.3.2. Students are given proper tools and supplies, restore cable jacket to meet or exceed original electrical specifications. 6.3.1.1.11. CABLE JACKET REPAIR: 6.3.1.1.11.1. The Instructor shall present the basic tools, materials, and procedures for repairing damaged armored and unarmored cable jackets. 6.3.1.1.11.2. TERMINAL OBJECTIVE: 6.3.1.1.11.2.1. Students are given the proper tools and supplies, to restore damaged cable jacket insulation of electrical cables (armor and/or sheath damage only) to meet or exceed original electrical specifications, with conductors and water-sealing compounds being intact in accordance with the guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-¬2003 (NAVY) EPISM. 6.3.1.1.11.3. ENABLING OBJECTIVE: 6.3.1.1.11.3.1. Students are given damaged electrical cables (armored and unarmored), identify the damage in each, and the procedure to repair cable jacket damage. 6.3.1.1.12. TESTING CABLES: 6.3.1.1.12.1. The Instructor shall present the basic test instruments required to check cables for opens, shorts, and grounds. 6.3.1.1.12.2. TERMINAL OBJECTIVES: 6.3.1.1.12.2.1. Students are given the test instrument (megger), to measure insulation resistance to ensure that two or more electrical conductors or cables are properly separated from each other or from ground by an insulating material. 6.3.1.1.12.2.2. Students are given test instrument (multimeter), to perform a continuity check to ensure there are no shorts, opens, grounds, or leads incorrectly connected 6.3.1.1.12.3. ENABLING OBJECTIVE: 6.3.1.1.12.3.1. Students are given a list of test instruments and their uses, match each test instrument with its appropriate use. 6.3.1.1.13. CABLE ID AND MARKING: 6.3.1.1.13.1. The Instructor shall present the methodology used for the numbering of electrical systems and equipment for locating and identifying purposes, and the proper use of shipboard Isometric Wiring Diagrams. 6.3.1.1.13.2. TERMINAL OBJECTIVE: 6.3.1.1.13.2.1. Students are given various circuit numbers, students are to identify electrical cables to include terminations, equipment type and type of service. 6.3.1.1.13.2.2. Students shall state the requirements for cable identification tags. 6.3.1.1.13.2.3. Students are given a cable tags to obtain the correct Isometric Wiring Diagrams; determine cable route and location of nearest connection box. 6.3.1.1.14. CABLE PULLING TECHNIQUES: 6.3.1.1.14.1. The Instructor shall present information on planning, preparation, and proper procedures to remove and install cables and cableways. 6.3.1.1.14.2. TERMINAL OBJECTIVE: 6.3.1.1.14.2.1. Students are to pull dead ended cable from ship's cableways using proper tools and materials, observing all standard electrical safety precautions in accordance with the guidelines specified in the Electric Plant Installation Standard Methods DOD-STD-2003 (NAVY) EPISM. 6.3.1.1.14.2.2. Students are to install cable in ship's cableways using proper tools and materials, observing all standard electrical safety precautions in accordance with the guidelines specified in the Electric Plant Installation Standard Methods, DOD-STD-¬2003 (NAVY) EPISM. 6.3.1.1.14.3. ENABLING OBJECTIVE: 6.3.1.1.14.3.1. Students will establish whether a dead ended cable is de-energized by frisking, if energized, determine the source and tag out of service using the ships' tag-out procedure prior to removing. 6.3.1.1.14.3.2. Students will pull dead ended cable from ship's cableways using proper tools and materials, observing all standard electrical safety precautions in accordance with the guidelines specified in the Electric Plant Installation Standard Methods, DOD-STD-¬2003 (NAVY) EPISM. 6.3.1.1.14.3.3. Students will install cable in ship's cableways using proper tools and materials, observing all standard electrical safety precautions in accordance with the guidelines specified in the Electric Plant Installation Standard Methods, DOD-STD-¬2003 (NAVY) EPISM. 6.3.1.1.15. CABLEWAY INSPECTION: 6.3.1.1.15.1. The Instructor shall present information that will help personnel look for discrepancies and problems in cables and cableways and necessary steps to correct them. 6.3.1.1.15.2. TERMINAL OBJECTIVE: 6.3.1.1.15.2.1. Students are given illustrations of electrical cable and cableway deficiencies to identify each deficiency and assign the proper category type using the information provided in the Cable Inspection Criteria NAVSEA INST. 9304.1D 6.3.1.1.15.3. ENABLING OBJECTIVE: 6.3.1.1.15.3.1. Students match the category deficiency to the statement that best describes its definition. 6.4. Contractor Personnel: 6.4.1. Each instructor shall posses NAVSEA Certification as instructors for Shipboard Electrical Cable and Cableway Inspection and Reporting Procedures. 7. GOVERNMENT FURNISHED INFORMATION: 7.1. Names of Coast Guard personnel to attend the training 7.2. With exception of the AMSEC Facility in Virginia Beach, VA location the following apply: 7.2.1. Two local Points of Contact at the USCG facilities hosting the training to AMSEC to facilitate AMSEC and Coast Guard personnel communications of local needs. 8. GOVERNMENT FURNISHED MATERIAL: NA 9. GOVERNMENT FURNISHED EQUIPMENT: 9.1 With exception of the AMSEC Facility in Virginia Beach, VA location the following apply: 9.1.1. A room with enough space to teach the class and hold materials AMSEC instructors bring for instruction. 9.1.2. A dry erase or chalk board. 10. CONTRACTOR FURNISHED EQUIPMENT: 10.1. Contractor shall furnish all equipment needed to complete the course. Including multimedia equipment and training aids. 11. CONTRACTOR FURNISHED MATERIAL: 11.1. Per training session: 11.1.1. Study materials 11.1.2. Manuals 11.1.3. Consumables needed to complete assigned tasks 11.1.4. Up to twenty (20) Certificates of Completion 11.1.5. Up to twenty (20) wallet Certification cards 11.1.6. Course Critiques 12. TRAVEL REQUIREMENTS: 12.1. With exception of the AMSEC Facility in Virginia Beach, VA location the following apply: 12.1.1. AMSEC instructors will travel to the locations to teach at USCG facilities. 12.1.2. Travel to be paid IAW JFTR. 13. TRANSPORTATION OF EQUIPMENT/MATERIAL: 13.1. AMSEC will ship required course materials and training aids to and from the training locations. 14. DATA DELIVERABLES: 14.1. Each student shall be presented with a certificate showing completion of the course. 14.2 The contractor shall obtain written feedback from the students upon completion of the course. 15. SUB-CONTRACTING REQUIREMENTS: NA 16. ACCEPTANCE PLAN: NA 17. OTHER CONDITIONS REQUIREMENTS: NA 18. LIST OF ATTATCHEMENTS: NA
Web Link: FBO.gov Permalink
(https://www.fbo.gov/spg/DHS/USCG/C2EC/HSCG44-11-Q-PC7185/listing.html)
Record: SN02463113-W 20110604/110602235335-557f18b29d5ceb9a3b6b729f73e1a702 (fbodaily.com)
Source: FedBizOpps Link to This Notice
(may not be valid after Archive Date)

| FSG Index | This Issue's Index | Today's FBO Daily Index Page |

Loren Data's SAM Daily™

U -- PURCHASE OF TRAINING SERVICES