SOLICITATION NOTICE
23 -- Repair two oil spill response isometrics vacuum trucks.
- Notice Date
- 5/23/2013
- Notice Type
- Combined Synopsis/Solicitation
- Contracting Office
- N68836 NAVSUP Fleet Logistics Center Jacksonville Mayport Office Bldg. 191, Naval Station Mayport Fleet Contracting Center Mayport, FL
- ZIP Code
- 00000
- Solicitation Number
- N68836RC027X6
- Response Due
- 5/28/2013
- Archive Date
- 6/12/2013
- Point of Contact
- Miguel E Rivera 904-270-5699 x125
- Small Business Set-Aside
- Total Small Business
- Description
- STATEMENT OF WORK (SOW) FOR THE REPAIR OF TWO OIL SPILL RESPONSE ISOMETRICS VACUUM TRUCKS 1. SCOPE Complete repairs of two 1800 gallon Isometrics vacuum trucks to include removal of tank, abrasive blast, prime and paint frame, tank, accessories, rims and cab as outlined below.. 2. TRUCK IDENTIFICATION 2.1 Manufacture: Isometrics vac system, vehicle VIN 1HTSCABR6SH674694. 1800 gallon tank. Truck is located at Naval Air Station, Jacksonville, FL. 2.2 Manufacture: Isometrics vac system, vehicle VIN 1HTSCABN92H547273. 1800 gallon tank Truck is located at Naval Station Mayport, FL. 3. REQUIREMENTS 3.1 Contractors facility must be within 35 miles of NAS Jacksonville. 3.2 Military personnel will drive truck to and from contractor facility. 3.3 Contractor must have the lift capability to remove tank from truck. 4. PERIOD OF PERFORMANCE 4.1 All work on trucks must be completed 90 days from contract award date. 5. WORK TO BE ACCOMPLISHED 5.1 Truck referenced in 2.1 and 2.2, to be delivered as arranged with government representative. 5.1.2 Remove cab mirrors and brackets and prime, paint and replace fasteners with non-ferrous. 5.1.3 Prepare cab surface for painting, prime and paint cab using commercial industrial grade professional paint, white. 5.1.4 Blast, prime and paint front and rear bumper. Striped black and yellow. 5.1.5 Remove top tank access covers, rear access covers, valves and piping from inlet and outlet. 5.1.6 Remove gaskets, blast, prime and paint with Sherwin Williams SeaGuard 5000 Primer and topcoat with Sherwin Williams Acrolon 218 (white). 5.1.7 Replace gaskets on covers, clean all threaded strong back fasteners. 5.1.8 Remove storage boxes from sides of truck, remove fenders, remove tank, remove vacuum pump. 5.1.9 Repair by welding, cropping out and replacing any deteriorated metal on boxes and fenders. Drill drain holes through bottom of boxes. 5.1.10 Open and inspect surge tank and oil collection tank, clean, replace gaskets and notify government representative to inspect. 5.1.11 Thoroughly clean interior of cab. Repair and recover bench seat on one truck. 5.1.12 Inspect all lights and repair/replace as required. 5.1.13 Replace wiper blades 5.1.14 Abrasive blast exterior of tank, truck frame, storage boxes, vacuum pump oil collection tank, surge tank, vacuum pump, bed plate, fenders, truck rims, spare tire carrier, fuel tanks, cab steps, rear and front bumper. 5.1.15 Sweep blast or mechanically clean interior of vac tank, removing rust. Inspect tank for holes, coat inside of tank with oil film. 5.1.16 Inspect tank float assembly and repair or replace as required. Notify government representative. 5.1.17 Prime and paint as follows: - Apply 30 mil Polyurea coating on lower half of tank, fenders, inside and outside of storage boxes. Topcoat with Acrolon 218 (black). - Apply one coat of Sherwin Williams Seaguard 5000 primer to upper half of tank exterior, frame, vacuum pump collection tank, surge tank, spare tire carrier, vacuum pump bed plate, truck rims and bumpers as per manufactures recommendations. Using spray process. -Apply one coat of Sherwin Williams Acrolon 218 (white) to all items above, except fuel tanks and cab steps painted (black). Using spray process. 5.1.18 Paint and reinstall tank, vacuum pump aligning with pulley system, replace (3) three inch NPT reinforced petroleum product hoses on the vacuum system. 5.1.19 Reinstall storage boxes. 5.1.20 Reinstall fenders. 5.1.21 Replace top two ladder fasteners with non-ferrous material. 5.1.22 Reinstall inlet and outlet tank connections and valves, install caps with lanyard on piping ends. Lubricate all valves and gaskets with silicone grease. 5.1.23 Purchase and install decals for No Smoking Within 50 Feet on sides and back of tank. Decal on vacuum pump operating handle for vac, N, press , Decal on tank level indicator for E, , , , F 5.1.24 Inspect and operate truck with government representative. The Government Point of Contact for the contract is: Robert E. Novotny CNRSE, Code N313 Box 102, Naval Air Station Jacksonville, FL 32212-0102 904-542-0954 904-887-4093 cell
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DON/NAVSUP/N68836Mayport/N68836RC027X6/listing.html)
- Record
- SN03070711-W 20130525/130523235559-9ced05c3b79009987065df5cac980aa5 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |