SOLICITATION NOTICE
13 -- 81mm Gas Adsorbent Modules (GAMs)Invitation for Bid(IFB)
- Notice Date
- 7/11/2013
- Notice Type
- Presolicitation
- Contracting Office
- ACC - New Jersey, Center for Contracting and Commerce, Building 10 Phipps RD, Picatinny Arsenal, NJ 07806-5000
- ZIP Code
- 07806-5000
- Solicitation Number
- W15QKN-13-B-0006
- Response Due
- 7/26/2013
- Archive Date
- 9/9/2013
- Point of Contact
- Michael Samra, 973-724-3965
- E-Mail Address
-
ACC - New Jersey
(michael.w.samra.civ@mail.mil)
- Small Business Set-Aside
- N/A
- Description
- The Army Contracting Command-New Jersey (ACC-NJ), Picatinny Arsenal, NJ 07806-5000, on behalf of the Office of the Project Manager of Combat Ammunition Systems, intends on issuing an Invitation for Sealed Bids for the manufacture and delivery of 81mm Gas Adsorbent Modules (GAMs) to be used in the M819 Smoke Cartridge packaging on or about September 2013. It is the intention of the Government that the procurement shall be restricted to Savit Corporation, Rockaway, NJ and Design West Technologies, Tustin, CA, as they are the only two companies that have the capability to produce and deliver the M819 GAM within the time required. The award shall be for the purchase of 14,560 ea M819 GAM's with deliveries beginning in April 2014. Offerors must be able to produce and deliver 5,000 GAM's in April 2014, 5,000 GAM's in May 2014 and 4,560 GAM's in June 2014. The Invitation for Sealed Bids is intended to be issued under restricted competition using 10 U.S.C. 2304(c)(1), as authorized by FAR 6.302-1(a)(2)(ii)(B), Only One Responsible Source or a Limited Number of Responsible Sources. The USG intends to award a single Firm Fixed Price contract. The GAM consists of a plastic circular housing filled with two packets of a chemical adsorbent. The plastic housing is made of high impact polystyrene and has an approximate height of 1.85 inches, approximate outer diameter (OD) of 3.1 inches, and approximate inner diameter (ID) of 2.3 inches. The plastic housing is divided into two interlocking pieces. Each piece consists of an upper and lower housing. Two halves are then combined to make the entire housing. The halves are held together with a piece of identifying tape with a warning printed on it. The housing holds two Tyvek bags containing the commercially available phosphine adsorbent. Each bag is held inside the housing with two packet retainers. The retainers are made of Melt Processable Rubber (MPR) and are approximately 1.68 inches tall, with a cross-section of.265 inches by.335 inches. Additionally they contain a C notch to retain the edge of the bag. This notice does not constitute issuance of an Invitation for Sealed Bids, nor is the Government obligated to issue one. Point of contact for this requirement is Mike Samra, ACC-NJ-CA, Building 10, Picatinny Arsenal, NJ 07806 5000. Telephone inquiries will not be accepted. E-mail any questions to michael.w.samra.civ@mail.mil
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/notices/fb90ea3044232fb71fd6be5183f878a5)
- Place of Performance
- Address: ACC - New Jersey Center for Contracting and Commerce, Building 10 Phipps RD Picatinny Arsenal NJ
- Zip Code: 07806-5000
- Zip Code: 07806-5000
- Record
- SN03114348-W 20130713/130711235713-fb90ea3044232fb71fd6be5183f878a5 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |