SOURCES SOUGHT
66 -- Sources sought synopsis for a Computer Controlled Brake Actuator
- Notice Date
- 8/15/2013
- Notice Type
- Sources Sought
- NAICS
- 334519
— Other Measuring and Controlling Device Manufacturing
- Contracting Office
- ACC-APG - Installation Division, Directorate of Contracting, 4118 Susquehanna Avenue, Aberdeen Proving Ground, MD 21005-3013
- ZIP Code
- 21005-3013
- Solicitation Number
- W91ZLK-13-T-0272
- Response Due
- 8/20/2013
- Archive Date
- 10/14/2013
- Point of Contact
- Kenneth Harlan, 443-861-4731
- E-Mail Address
-
ACC-APG - Installation Division
(kenneth.p.harlan.mil@mail.mil)
- Small Business Set-Aside
- N/A
- Description
- W91ZLK-13-T-0272 SOURCES SOUGHT SYNOPSIS The U.S. Army Contracting Command (ACC), Aberdeen Proving Ground (APG), Tenant Division located at Aberdeen Proving Ground, MD, is seeking information on businesses that can provide the below described scientific equipment. This is a market survey for information only. THIS IS NOT A REQUEST FOR PROPOSALS OR QUOTATIONS, AND NO CONTRACT WILL BE AWARDED FROM THIS SOURCES SOUGHT SYNOPSIS. The purpose of this synopsis is to gain knowledge of interest, capabilities and qualifications of businesses that can support this requirement. The North American Industry Classification System (NAICS) Code for this requirement is 334519, Other Measuring and Controlling Device Manufacturing. DESCRIPTION OF REQUIREMENT: Computer Controlled Brake Actuator. The Computer Controlled Brake Actuator consists of two major parts, the electronics box and the brake servo actuator. The electronics box contains a microcontroller section and a power section. The brake servo actuator is a linear-acting unit with integral load cell and position encoder. Together, the electronics box and actuator will provide closed loop control for brake pedal travel, application force or vehicle deceleration. The system shall meet the performance requirements described in Federal Motor Vehicle Safety Standards (FMVSS) 105, 121 and FMVSS 135 as well as International Standards Organization (ISO) 21994. 1.Electronics Box maximum number of inputs: 8 2.Electronics Box Input Type: voltage 3.Electronics Box sample rate maximum: 1000 Hz per input 4.Electronics Box input and output have full galvanic isolation 5.Electronics Box minimum number of counter inputs: 1 6.Electronics Box maximum number of outputs: 6 7.Electronics Box analog outputs for parameters; pedal travel, pedal force, deceleration, trigger event and speed. 8.Electronics Box required input voltage: 10-18 Volts Dc 9.Electronics Box must contain enough batteries to power the attached servo motor. 10.Brake Servo Actuator shall be a minimum quote mark ball screw type. 11.Brake Servo Actuator shall contain integral load cell for application force measurement and control. 12.Brake Servo Actuator shall contain an integral position encoder for the measurement and control of actuator position. 13.Brake Servo Actuator shall provide a maximum static force of 450 pounds. 14.Brake Servo Actuator shall have a maximum speed of 50 inches per second. 15.Brake Servo Actuator shall include a seat frame assembly for mounting. 16.Interconnect cables between units shall be provided. 17.Maximum Electronics Box weight of 25 pounds. SUBMISSION INSTRUCTIONS: If you believe your firm qualifies as a small business under the aforementioned criteria and has qualified personnel, relevant past performance experience, and the technical capability to manufacture the type of equipment specified in the Description of Requirement, please submit a technical capability statement including the following information: (1) company name and mailing address; (2) point of contact (name, telephone number, and email address); (3) technical capability statement. This Requirement Description is currently in DRAFT format; if you would like to comment on this, please include your comments in your submittal. Again, this announcement is being used solely to gain knowledge of interest, capabilities and qualifications of businesses that can support this requirement. THIS IS NOT A REQUEST FOR PROPOSALS NOR IS THE TECHNICAL CAPABILITY SATEMENT CONSIDERED TO BE A PROPOSAL. No reimbursement will be made for any costs associated with providing information in response to this synopsis or any follow-up information requests. Please send information via email to SSG Kenneth P. Harlan, at kenneth.p.harlan.mil@mail.mil by 20 August 2013, 5 p.m. Eastern Standard Time. NO TELEPHONE REQUESTS WILL BE HONORED. ALL QUESTIONS OR RESPONSES MUST BE SENT VIA EMAIL.
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/notices/8443174d237aceeac6ccf051d5485cbc)
- Place of Performance
- Address: ACC-APG - Installation Division Directorate of Contracting, 4118 Susquehanna Avenue Aberdeen Proving Ground MD
- Zip Code: 21005-3013
- Zip Code: 21005-3013
- Record
- SN03151319-W 20130817/130816000459-8443174d237aceeac6ccf051d5485cbc (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |