SOLICITATION NOTICE
10 -- FOOT PISTON
- Notice Date
- 11/6/2013
- Notice Type
- Presolicitation
- NAICS
- 336413
— Other Aircraft Parts and Auxiliary Equipment Manufacturing
- Contracting Office
- Defense Logistics Agency, DLA Acquisition Locations, DLA Land and Maritime, P O Box 3990, Columbus, Ohio, 43218-3990, United States
- ZIP Code
- 43218-3990
- Solicitation Number
- SPE7L414R0002
- Archive Date
- 1/7/2014
- Point of Contact
- Michele Beasley, Phone: 6146927572
- E-Mail Address
-
michele.beasley@dla.mil
(michele.beasley@dla.mil)
- Small Business Set-Aside
- N/A
- Description
- NSN# 1095-01-186-1540 FOOT PISTON 498 EACH / 996 W/OPTION SOL OPEN/CLOSE: 11/21/2013 - 12/23/2013 ***************************************************** ITEM DESCRIPTION: FOOT, PISTON: END ITEM: ERU - 136 (BRU-36 in Crit. Data Viewer) THIS IS A NAVY IDENTIFIED CRITICAL SAFETY ITEM (CSI) ALL REQUESTS FOR WAIVERS OR DEVIATIONS MUST BE FORWARDED TO THE DSC CONTRACTING OFFICER FOR REVIEW AND APPROVAL. ALL ITEMS OF SUPPLY SHALL BE MARKED IAW MIL-STD-129. IN ADDITION, EACH UNIT PACK WILL BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE), CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S CAGE CODE AND PART NUMBER.,, THIS ITEM IS A "DEFENSE ARTICLE" AS DEFINED IN AND SUBJECT TO THE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS (22 C.F.R. 120-30) AND THE ARMS EXPORT CONTROL ACT (22 U.S.C.A. 2778-2799). ANY MANUFACTURER OR EXPORTER OF DEFENSE ARTICLES IS REQUIRED TO REGISTER WITH THE DIRECTORATE OF DEFENSE TRADE CONTROLS (DDTC), DEPARTMENT OF STATE. DOCUMENTARY EVIDENCE OF REGISTRATION MAY BE REQUIRED PRIOR TO AWARD. ADDITIONAL EXPORT RESTRICTIONS APPLY AS INDICATED HEREIN. FAILURE TO SUBMIT DDTC REGISTRATION WHEN REQUESTED WILL MAKE A QUOTE/OFFER INELIGIBLE FOR AWARD. THE ITEM BEING PROCURED IS A CRITICAL GUN PART ITEM WITH UNIQUE REQUIREMENTS. PRODUCT INSPECTION WILL BE CONDUCTED BY THE DCMA QAR AT THE ACTUAL MANUFACTURER'S FACILITY IDENTIFIED ON THIS CONTRACT. THE IDENTIFICATION OF THE ACTUAL MANUFACTURER MUST BE SUBMITTED TO THE CONTRACTING OFFICER FOR INCLUSION IN THE AWARD. UPON AWARD, ANY CHANGES TO THE ABOVE MUST BE APPROVED BY THE PCO VIA FORMAL CONTRACT MODIFICATION. CERTIFICATE OF CONFORMANCE IS NOT AUTHORIZED. IF AQLS ARE LISTED IN THE SPECIFICATION(S) OR DRAWING(S) THEY MAY BE USED TO ESTABLISH THE AUTHORIZED SAMPLE SIZE,HOWEVER,THE ACCEPTANCE NUMBER FOR THIS CONTRACT IS ZERO;I.E.,THIS CONTRACT REQUIRES A SAMPLING PLAN THAT ACCEPTS ON ZERO DEFECTS AND REJECTS ON ONE OR MORE DEFECT(S). CONTRACTOR/MANUFACTURER IS REQUIRED TO ESTABLISH AND MAINTAIN A CALIBRATION SYSTEM THAT MEETS THE REQUIREMENTS OF ANSI/NCSL Z540-1-1994, AMERICAN NATIONAL STANDARD FOR CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT-GENERAL REQUIREMENTS, OR ISO 10012-1, QUALITY ASSURANCE REQUIREMENTS FOR MEASURING EQUIPMENT- PART 1, METROLOGICAL CONFIRMATION SYSTEM FOR MEASURING EQUIPMENT. DLAD 52.246-9003, MEASURING AND TEST EQUIPMENT, APPLIES. CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL AGREEMENTS. TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, "MILITARY CRITICAL TECHNICAL DATA AGREEMENT," FORM IS AVAILABLE AT THE WORLD WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO: DLA LOGISTICS INFORMATION SERVICE FEDERAL CENTER 74 WASHINGTON AVE., NORTH BATILE CREEK, MI 49017-3084 TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT, DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 "EXEMPTIONS OF GENERAL APPLICABILITY," AND/OR EAR PART 740 ARE APPLICABLE. NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL DATA ARE REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO RECEIVE A COPY OF THE EXPORT CONTROLLED TECHNICAL DATA. NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY PERMITTED BY DODD 5230.25.",, DLAD PROVISION 52.211-9009 IS APPLICABLE TO THIS SOLICITATION, THEREFORE SURPLUS MATERIAL WILL NOT BE CONSIDERED. IF PRESENT IN THE SOLICITATION, PROVISION 52.211-9003 AND CLAUSE 52.211-9000 ARE NOT APPLICABLE.,, FAR CLAUSE 52.246-11 APPLIES A QUALITY MANAGEMENT PROGRAM MEETING THE REQUIREMENTS OF ISO 9001:2008 OR THE FOLLOWING TAILORED VERSION OF ISO 9001:2008 IS REQUIRED OR A PROGRAM EQUIVALENT TO THE TAILORED VERSION OF THE ISO 9001:2008 IS REQUIRED. DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008 4.2.1 General, Documentation Requirements [b and d only] 4.2.2 Quality manual 4.2.3 Control of documents 4.2.4 Control of records 6.2.2 Competence, training and awareness 6.4 Work environment (if applicable) 7.1 Planning of product realization 7.2.1 Determination of requirements related to the product 7.2.2 Review of the requirements related to product 7.2.3 Customer communication 7.3.7 Control of design and development changes 7.4.1 Purchase Product 7.4.3 Verification of purchased product 7.5.1 Control of production and service provision 7.5.3 Identification and traceability 7.5.4 Customer property (if applicable) 7.5.5 Preservation of product 7.6 Control of monitoring and measuring equipment 8.1a,,General for Measurement, Analysis and Improvement 8.2.2 Internal Audit 8.3 Control of nonconforming product 8.2.4 Monitoring and measurement of product 8.5.2 Corrective action 8.5.3 Preventive action THIS IS A NAVY IDENTIFIED CRITICAL SAFETY ITEM (CSI). ALL REQUESTS FOR WAIVERS OR DEVIATIONS MUST BE FORWARDED TO THE DSC CONTRACTING OFFICER FOR REVIEW AND APPROVAL.. ALL ITEMS OF SUPPLY SHALL BE MARKED IAW MIL-STD-129. IN ADDITION, EACH UNIT PACK WILL BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE), CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S CAGE CODE AND PART NUMBER. SPECIAL MARKINGS CODE 40 APPLIES. EACH UNIT PACKAGE WILL BE MARKED WITH THE NSN, CONTRACT NUMBER, LOT NUMBER, CONTRACTOR CAGE CODE, MANUFACTURER CAGE CODE, AND PART NUMBER. BOEING COMPANY, THE 76301 P/N MD31623-1085 BOEING COMPANY, THE DBA BOEING 0PXV4 P/N MD31623-1085 FLIGHT REFUELLING LTD U1918 P/N MD31623-1085
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DLA/J3/DSCC/SPE7L414R0002/listing.html)
- Record
- SN03229133-W 20131108/131106233849-0241907c71b7087382a0f539d4053279 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |