Loren Data's SAM Daily™

FBO DAILY - FEDBIZOPPS ISSUE OF DECEMBER 25, 2014 FBO #4779
SOLICITATION NOTICE

83 -- CLOTHING, LEATHER, TYPE I, CLASS 2, APRON, - Quality Systems Requirements

Notice Date

12/23/2014
 

Notice Type

Combined Synopsis/Solicitation
 

NAICS

315990 — Apparel Accessories and Other Apparel Manufacturing
 

Contracting Office

Defense Logistics Agency, DLA Acquisition Locations, DLA Troop Support - Clothing & Textiles, 700 Robbins Avenue, Philadelphia, Pennsylvania, 19111-5096, United States
 

ZIP Code

19111-5096
 

Solicitation Number

spe1c115q0159
 

Point of Contact

Albert J. Ruigrok Jr, Phone: 215-737-7489, Stephanie A. Shafer, Phone: 215-737-5145
 

E-Mail Address

Albert.Ruigrok@dla.mil, Stephanie.Shafer@dla.mil
(Albert.Ruigrok@dla.mil, Stephanie.Shafer@dla.mil)
 

Small Business Set-Aside

N/A
 

Description

4155.2 Quality Assurance Program for DLA Inventory Control Points 4155.3 Quality Systems Requirements The proposed acquisition covers a requirement for the CLOTHING, LEATHER, TYPE I, CLASS 2, APRON, SPLIT LEG. NSN 8415-00-250-2531 MADE IN ACCORDANCE WITH A-A-55098 DATED 04 DECEMBER 1992 AND DRAWING 2-1-522. This solicitation will be issued as 100% unrestricted. The quantity is 950 each. The acquisition will be FOB Destination, Inspection and Acceptance at Source. Delivery will be required 120 days after date of order. All materials used in the fabrication are to be furnished by the successful offeror. It is anticipated this solicitation will be posted to the DLA Internet Bid Board System (DIBBS) by December 2014. All offerors MUST be registered in *SAM in order to be eligible for award. All responsible sources may submit offers which, if timely received, shall be considered. submit offers which, if timely received, shall be considered. *The System for Award Management (SAM) is a free web-site which consolidates Federal procurement systems and the Catalog of Federal Domestic Assistance. You can access SAM via https://www.sam.gov/portal/public/SAM/. Availability of solicitations, FAR 5.102(d) applies, as our office no longer issues solicitations or amendments in paper form. Solicitation will be posted on https://www.dibbs.bsm.dla.mil/ Detailed system requirements and instructions for registration can be found on the DLA DIBBS Home Page accessed on https://www.dibbs.bsm.dla.mil/. A few highlights of the information that will be found include: 1. On the DLA Internet Bulletin Board System (DIBBS) Home Page, click the VENDOR REGISTRATION link to begin the registration process. 2. In order to register for access to secure portions of DLA DIBBS, the company you are representing must already be registered in the Central Contractor Registration (CCR) system. 3. A Commercial and Government Entity (CAGE) Code registration will be processed immediately. A User ID will appear on the registration screen and a password will be sent separately to the email address of the Super User. If a CAGE is already registered on DLA DIBBS, the name and email address of the Super User will be provided. The Super User should be contacted to set-up additional accounts, logons and passwords for their CAGE. DIBBS Super User * If your CAGE has already been registered on DIBBS, the name and email address of the person designated as your super user will be provided. * The representative who starts the DIBBS registration process has the option to accept their CCR registration POC as the DIBBS super user, or they can designate themselves or another person to act as the super user for the CAGE. * The super user acts as the account administrator for a CAGE. They can add up to ninety-eight (98) additional users, provide user IDs and passwords, modify existing users, and control the login status of each user for their CAGEs through My Account (Account Maintenance). The Defense appropriations and authorization acts and other statutes (including what is commonly referred to as "The Berry Amendment") impose restrictions on the DoD's acquisition of foreign products and services. Generally, Clothing and Textile items (as defined in DFARS clause 252.225-7012) and "specialty metals" (as defined in DFARS clause 252.225-7014), including the materials and components thereof (other than sensors, electronics, or other items added to, and not normally associated with clothing), must be grown, reprocessed, reused, melted or produced in the United States, its possessions or Puerto Rico, unless one of the DFARS 225.7002-2 exceptions applies. DLA Troop Support has developed a web-based system that allows manufacturers the ability to request specifications, patterns and drawings on our contracting page. To request technical data for DLA Troop Support Clothing and Textiles (C&T) solicitations, use the following link to the DLA Troop Support C&T Technical Data Repository area at http://www.troopsupport.dla.mil/Portal/sreqfrm.aspx CLOTHING, LEATHER, TYPE I, CLASS 2, APRON, SPLIT LEG. ADDITIONAL INFORMATION FOR A-A-55098:. CLOTHING, LEATHER: TYPE I, CLASS 2, APRON, SPLIT LEG, SHALL BE MADE IN ACCORDANCE WITH A-A-55098 DATED 04 DECEMBER 1992 AND DRAWING 2-1-522 INTERIM CHANGES TO A-A-55098: PAGE 3, PARAGRAPH 3, "THREAD", DELETE IN ITS ENTIRETY AND SUBSTITUTE: "THREAD. THE THREAD SHALL BE SPUN PARA-ARAMID INTERMEDIATE MODULUS OR COTTON THREAD USED FOR MACHINE AND HAND SEWING. THE THREAD SHALL BE A DYED KHAKI P-1, C. A. 66019 AND SHALL CONFORM TO THREAD SIZES LISTED BELOW:. PAGE 3, PARAGRAPH 4, LEATHER, LINE 4, DELETE "NATURAL" AND SUBSTITUTE "NATURAL AS PRODUCED BY THE TANNING AGENTS.".. PAGE 3, AFTER "LABELING" PARAGRAPH, ADD THE FOLLOWING NEW PARAGRAPH; "BAR CODE LABEL/TAG. EACH ITEM SHALL BE INDIVIDUALLY BAR CODED WITH A TYPE VIII, CLASS 17, LABEL/TAG OF DDD-L-20. THE LABEL/TAG SHALL BE LOCATED SO THAT IT IS COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND/OR PACKAGED AS SPECIFIED AND SHALL CAUSE NO DAMAGE TO THE ITEM.".. PAGE 6, "DEFECTS CONT" PARAGRAPH, AT THE END OF THE PARAGRAPH ADD; "BAR CODE OMITTED OR NOT READABLE BY SCANNER, HUMAN READABLE INTERPRE- TATION (HRI) OMITTED OR ILLEGIBLE, NOT VISIBLE ON FOLDED, PACKAGED ITEM, OR CAUSES DAMAGE TO ITEM.".. PAGE 7, UNDER PACKAGING, DELETE "OVERSEAS".. PAGE 8, AFTER MARKING, DELETE "DOMESTIC" AND DELETE PARAGRAPH THAT FOLLOWS PERTAINING TO "PACKAGING, PACKING...MARKING" IN ITS ENTIRETY.. ADDITIONAL INFORMATION FOR FED-STD-191: FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO END ITEM SPECIFICATION FOR REPLACEMENT ASTM. INTERIM CHANGES TO FED-STD-191A: TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT ONE INCH OF SPECIMEN LIES WITHIN THE CLAMP AND ONE INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF THE VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE". TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA 4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91". THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540, AND 1550. PARA 5.1 OF THESE TEST METHODS REQUIRE THE USE OF 1,1,1- TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-TRICHLORETHANE IS AN OZONE DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN BASIC OR ANY REFERENCED DOCUMENT. METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD. PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (INNER FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE." METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5, PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACK TEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60 MINUTES OR UNTILSAMPLES ARE DRY IN A ROTATING TUMBLE DRYER." PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACKTEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40 MINUTES OR UNTIL SAMPLES ARE DRY." METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1, PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1, PARA. 4: DELETE "APPARTUS" AND SUBSTITUTE "APPARATUS". PAGE 1, PARA. 5.1, LINE 3: AFTER "AT" DELETE"APPROXIMATELY". PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6: AFTER "TO" ADD "+-". PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING IT OVER THE SENSOR OPENING. THE SURFACE OF THE TEST SPECIMEN (BACK OR FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE RESIDUAL CHARGE LEVEL ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY. NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500 VOLTS YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A PERIOD OF 20 SECS. AT THE END OF THE 20 SECOND PERIOD, THE HIGH VOLTAGE (5000 VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS IMMEDIATELY GROUNDED. THE VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL BE PLOTTED ON THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL DISPLAY VOLTAGE AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT NECESSARY." PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE SPECIMEN DID" IN ITS ENTIRETY. PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND DECAY TIME TO 10% OF THE MAXIMUM VOLTAGE LEVEL ACHIEVED." PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE: "REVERSE VOLTAGE POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS." PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL BE INCLUDED FOR EACH OF THE WARP & FILLING DIRECTIONS, AS WELL AS THE OVERALL AVERAGE, FOR EACHFABRIC TESTED. THESE WILL BE OBTAINED BY AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS DOCUMENT, THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE MAXIMUM VOLTAGE IN BOTH THE WARP AND FILLING DIRECTIONS IS LESS THAN 4000 VOLTS, AND THE AVERAGE DECAY TIME (TO 10% MAXVOLTAGE) IS GREATER THAN 0.5 SECONDS IN BOTH THE WARP AND FILLING DIRECTIONS. IT SHALL BE INDICATED WHETHER THE FABRIC ISACCEPTABLE OR NON-ACCEPTABLE." PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE WITH "406D". AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY FOR THE TEST." (Ref. T0215) INTERIM CHANGES FOR PNP FUNGICIDE REQUIREMENTS:. SECTION 3 OF THE SPECIFICATION REFERENCED: DELETE ALL CURRENT REFERENCES TO THE FUNGICIDE PARANITROPHENOL. UNLESS OTHERWISE SPECIFIED, ONE OF THE FOLLOWING FUNGICIDES IS REQUIRED: 1. PARANITROPHENOL: THE LEATHER SHALL CONTAIN NOT LESS THAN 0.18 AND NOT MORE THAN 0.70 PERCENT PARANITROPHENOL FUNGICIDE WHEN TESTED AS SPECIFIED BELOW 2. VITASAN: THE LEATHER SHALL CONTAIN NOT LESS THAN 1.6 AND NOT MORE THAN 5.0 PERCENT OF THE ACTIVE INGREDI- ENT ORTHO-PHENYLPHENOL, WHEN TESTED AS SPECIFIED BELOW. 3. AMICAL: THE LEATHER SHALL CONTAIN NOT LESS THAN 300PPM AND NOT MORE THAN 1000PPM OF ACTIVE INGREDIENT DIIODOMETHYL-P-TOLYSULFONE, WHEN TESTED AS SPECIFIED BELOW.. TEST METHODS FOR ABOVE FUNGICIDE TREATMENTS 1. PARANITROPHENOL: THE TEST FOR CONCENTRATION OF PARANITROPHENOL IN THE LEATHER SHALL BE CONDUCTED IN ACCORDANCE WITH TEST METHOD 6711 OF FED-STD-311.. 2. VITASAN: THE TEST METHOD TO DETERMINE ORTHO-PHENYLPHENOL CONCENTRATION IN LEATHER SHALL BE CONDUCTED IN ACCORDANCE WITH METHOD I, TYPE I OF MIL-L-8067.. 3. AMICAL: THE TESTING TO DETERMINE THE CONCENTRATION OF AMICAL IN THE LEATHER SHALL BE CONDUCTED IN ACCORDANCE WITH THE FOLLOWING TEST PROCEDURE: DRYING AND GRINDING. BEFORE GRINDING THE LEATHER MUST BE CUT INTO SMALL PIECES, APPROX- IMATELY 1/2 INCH BY 1/2 INCH, WHICH IN TURN ARE DRIED AT ROOM TEMPERATURE OVERNIGHT. FOR CHEMICAL ANALYSIS GRIND THE DRIED LEATHER PIECES IN ACCORDANCE WITH PARAGRAPH 6.3.7 OF ASTM 2813 STANDARD PRACTICE FOR PHYSICAL AND CHEMICAL TESTS. HPLC DETERMINATION. STOCK STANDARD PREPARATION. WEIGH ACCURATELY APPROXIMATELY 100 MG OF DIIODOMETHYL-PARA- TOLYLSULFONE INTERNAL REFERENCE STANDARD (IRS), (SEE 6.7.1) INTO A 100 ML VOLUMETRIC FLASK. ADD APPROXIMATELY 50 ML OF ACETONITRILE, STOPPER AND SONICATE TO AID DISSOLUTION (ABOUT 1 MINUTE). DILUTE TO VOLUME WITH ACETONITRILE. WORKING STANDARDS PREPARATION. TRANSFER 3ML ALIQUOTS OF THE STOCK STANDARD PREPARATION TO 25,50,100 AND 250ML VOLUMETRIC FLASKS. DILUTE TO VOLUME WTIH ACETONITRILE. THESE STANDARDS CONTAIN APPROXIMATELY 12,30,60 AND 120PPM OF DIIODOMETHYL-PARA-TOLYLSULFONE. NOTE: A LOWER STANDARD MAY BE REQUIRED FOR SAM- PLES CONTAINING VERY LOW LEVELS OF AMICAL. SOL- UTIONS OF DIIODOMETHYL-PARA-TOLYLSULFONE MUST BE STORED IN DARKNESS TO PREVENT DEGRADATION. MINI- MIZE EXPOSURE TO LIGHT DURING PREPARATION AND USE. THE STANDARD PREPARATIONS MAY BE RETAINED ONE MONTH. SAMPLE PREPARATION. ACCURATELY WEIGH APPROXI- MATELY 4-5G OF SAMPLE INTO A 150ML BEAKER. ADD 75ML-100ML OF ACETONITRILE. COVER SAMPLES WITH PARAFILM: MIX 24 HOURS ON A MAGNETIC STIR PLATE. THE FOLLOWING DAY, ALLOW SAMPLES TO SETTLE; REMOVE NECESSARY EQUIPMENT: (NOTE: SAMPLES MAY HAVE TO BE DILUTED FURTHER TO FALL WITHIN STANDARD CURVE.) HPLC SYSTEM WITH VARIABLE UV DETECTOR AND INTE- GRATING COMPUTER. SUITABLE SYRINGE AND GLASSWARE. A MICRO-BONDAPAK C18 COLUMN (WATERS ASSOCIATES, P/N 2734) OR EQUIVALENT. 0.45-MICRON POLYCARBONATE FILTERS (NUCLEPORE CORPORATION, CATALOG NO. 111107) OR EQUIVALENT. CALCULATOR CAPABLE OF DOING LINEAR REGRESSION. REAGENTS: ACETONITRILE (CHROMATOGRAPHIC GRADE). TYPICAL MOBILE PHASE. MIX 550ML OF DISTILLED WATER, 450ML OF ACETONITRILE. FILTER AND DEGAS THE SOLUTION. THE CONCENTRATION MAY BE VARIED TO MEET SYSTEM SUITABILITY REQUIREMENTS WITHIN THE RANGE 50% TO 40% ACETONITRILE. TYPICAL CHROMATOGRAPHIC CONDITIONS: INJECTION VOLUME 20 MICROLITERS FLOW 2.5 ML/MINUTE DETECTOR 235 MM SYSTEM SUITABILITY. INJECT THE HIGHEST WORKING STANDARD UNTIL 2% AGREEMENT IS REACHED BETWEEN TWO SUCCESSIVE INJECTIONS. CHROMATOGRAPH FOR APPROXIMATELY 15 MINUTES. DETERMINE THAT AFTER THE SOLVENT FRONT ONE IMPURITY PEAK ELUTES BE- FORE THE MAJOR PEAK. ELUTION FOR MONOIODOMETHYL PARA-TOLYLSULFONE AND DIIODOMETHYL-PARA- TOLYLSULFONE IS ABOUT 8.5 MINUTES. PROCEDURE. INJECT EACH STANDARD AND SAMPLE PREPARATION IN DUPLICATE ALLOWING EACH INJECTION TO RUN FOR AT LEAST 15 MINUTES. MEASURE THE PEAK RESPONSE FOR THE DIIODOMETHYL-PARA- TOLYLSULFONE. NOTE: THE RUN TIME MAY HAVE TO BE INCREASED FOR SAMPLES WITH LATE ELUTING PEAKS. PERFORM A LINEAR REGRESSION OF PEAK RES- PONSE (AREA) VERSUS CONCENTRATION FOR EACH OF COMPONENTS. FOR EACH COMPONENT: CONCENTRATION (PPM) IN LEATHER CONCENTRATION (PPM) FROM LINEAR REGRESSION TIMES 75 OVER SAMPLE WT (G). ADD THE FOLLOWING INFORMATION TO THE SECTION 6: WHEN A FUNGICIDE IS SPECIFIED: SOURCES SUGGESTED FOR FUNGICIDES ALTERNATE TO PARANITROPHENOL: FOR AMICAL AND IRS IS CHEMTAN COMPANY, EXETER NH 03833-0050. SUGGESTED SOURCE FOR VITASAN IS BLUMBERG CORPOR- ATION, NEWBURYPORT, MA 01950. ADDITIONAL INFORMATION FOR A-A-52094A: NO ADDITIONAL INFORMATION (ref. T1481) ADDITIONAL INFORMATION: FED-STD-751 HAS BEEN CANCELLED AND REPLACED BY ASTM-D-6193, 4/98 STANDARD PRACTICES FOR STITCHES AND SEAMS. THIS STANDARD SHOULD BE USED IN PREFERENCE TO FED-STD-751. (ref. T0216 - May 18, 2006) DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS. PART I AND II, JULY 2000 AND SUPPLEMENT, MARCH 2000 MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS: MIL-STD-147E DEPARTMENT OF DEFENSE 16 MAY 2008 STANDARD PRACTICE PALLETIZED UNIT LOADS STANDARDS (COMMERCIAL) ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets. MIL-STD-731 IS HEREBY CANCELLED, NOTICE 2 DATED 12/5/95. ASTM-D-6199 - "STANDARD PRACTICE FOR QUALITY OF WOOD MEMBERS OF CONTAINERS AND PALLETS" HAS BEEN ADOPTED AS A REPLACEMENT AS OF 7/29/98. (ref. T0340 - May 18, 2006) MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE, AND TENTAGE, GENERAL USE REPLACES DDD-L-20 (Ref. T0451 - June 19, 2007) INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075: PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L- 20" AND REPLACE "MIL-DTL-32075,". PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE TYPE VI FINISHED LABEL." UNDER "TEARING STRENGTH" DELETE: "(LB.) MINIMUM" AND SUBSTITUTE: "(GNS) MINIMUM." PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD "AND THE UNIVERSAL PRODUCT CODE (UPC) SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs." ADDITIONAL INFORMATION FOR FF-R-556:. NO ADDITIONAL INFORMATION FOLLOWS.. ADDITIONAL INFORMATION FOR JJ-W-155: INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS MIL-C-44436, ROLL #3729 (THE FOLIAGE GREEN 502 AREA OF THE PATTERN), AND REFERENCED FOR SHADE ONLY. THIS STANDARD IS TEMPORARY UNTIL FURTHER NOTICE. THIS APPLIES TO TYPE I, CLASS 6 AND TYPE I, CLASS 11. INTERIM SPECIFICATION CHANGES TO JJ-W-155H: PAGE 8, TABLE I, ACROSS FROM CLASS 3, UNDER MIN. YARNS PER INCH: DELETE "100" AND SUBSTITUTE "100 12/". PAGE 10, TABLE I, ACROSS FROM CLASS 29, UNDER MIN. YARNS PER INCH: DELETE FOOTNOTE "6/" AND SUBSTITUTE FOOTNOTE "10/". UNDER FOOTNOTE 11/: ADD "12/ 100 YARNS PER INCH OF 24/2 YARN OR 136 YARNS PER INCH OF 40/2 WITH 2 YARNS PER SHED." PAGE 12, PARA. 3.10.1 DELETE IN ITS ENTIRETY AND SUBSTITUTE "3.10.1 AQUEOUS COPPER-8-QUINOLINOLATE. THE WEBBING SPECIFIED IN 3.10 SHALL BE MILDEW TREATED WITH AQUEOUS COPPER 8-QUINOLINOLATE OR OTHER APPROVED AQUEOUS BASED MILDEW INHIBITOR. BECAUSE OF THE TIME NECESSARY TO CONDUCT FULL EVALUATION, ONLY THOSE TREATMENTS ALREADY APPROVED AND SO LISTED IN THE INVITATION FOR BIDS OR REQUESTS FOR PROPOSAL SHALL BE CONSIDERED ACCEPTABLE FOR THE RELATED PROCUREMENT." PAGE 26, PARA 4.3.1, LINE 8, BETWEEN "...(SEE 6.4)." AND "THE STARTING GAGE..." INSERT "AS AN ALTERNATE, ASTM-D4964 MAY BE USED TO DETERMINE ELASTIC LOOP TENSION AT SAME REQUIRED PERCENT ELONGATION AND UNDER SAME CARRIAGE LOAD PARAMETERS AS SPECIFIED IN TABLE III (I.E. FOR TYPE 1, CI 20 ELASTIC SET CRE CYCLE TO MAXIMUM 30 LBS. AND DETERMINE LOOP TENSION ON THIRD CYCLIC UPLOAD CURVE AT 50% ELONGATION). IF ALTERNATE TM IS USED, THEN ALLOW A +10% FACTOR TO MAXIMUM TENSION REQUIREMENT IN TABLE III." APPROVED AQUEOUS MILDEW TREATMENTS FOR: MIL-W-43638 WEBBING, TEXTILE, WOVEN FOR TENT FRAMING; MIL-W-5665, WEBBING, TEXTILE, COTTON WARP; MIL-W-530, WEBBING, TEXTILE, COTTON GENERAL PURPOSE, NATURAL OR IN COLORS; MIL-T-43566, TAPE, TEXTILE, COTTON OR POLYESTER, GENERAL PURPOSE, NATURAL OR IN COLORS, JJ-W-155, WEBBING, TEXTILE, (COTTON,ELASTIC): PRODUCT SUPPLIER CUNILATE 2002 MORTON INTERNATIONAL, INC 150 ANDOVER STREET DANVERS, MA. 01923 TEL: (508-774-3100) (ref. T0503 - May 19, 2006) ACCEPTABLE ALTERNATE MILDEW TREATMENT FOR 2,2' METHYLENE-BIS-(4-CHLOROPHENOL) 1. WHEN A SPECIFICATION SPECIFIES "2,2' METHYLENE-BIS-(4- CHLOROPHENOL)" MILDEW RESISTANT TREATMENT FOR COTTON TEXTILE MATERIALS, "RO-59" IS APPROVED AS AN ALTERNATIVE TREATMENT AND IS AUTHORIZED FOR USE. THIS CHANGE APPLIES TO PENDING AND FUTURE CONTRACTS USING TEXTILE MATERIALS THAT SPECIFY THE SUBJECT MILDEW RESISTANT TREATMENT. 2. THE PRODUCT MAY BE OBTAINED FROM: RO-59 INC. 1 CABOT PL #3 STOUGHTON, MA 02072 TELEPHONE (781) 264-1213 POC: MR. RONNIE BENDER 3. THE TEXTILE MATERIALS TREATED WITH RO-59 MILDEW INHIBITOR TREATMENT SHALL BE TESTED IN ACCORDANCE WITH AATCC TEST METHOD 30 - ANTIFUNGAL ACTIVITY, ASSESSMENT ON TEXTILE MATERIALS: MILDEW AND ROT RESISTANCE OF TEXTILE MATERIALS, TEST III. THE TREATED MATERIAL SHALL NOT EXHIBIT "MACROSCOPIC GROWTH (VISIBLE TO THE EYE)". ADDITIONAL INFORMATION FOR PPP-B-636: FEDERAL SPECIFICATION PPP-B-636 DATED JULY 12, 1981, INCLUDING INTERIM FEDERAL SPECIFICATION PPP-B-636L DATED JANUARY 1, 1991, IS HEREBY CANCELLED, AND REPLACED WITH ASTM-D-5118, STANDARD PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING BOXES, AND ASTM-D-1974, STANDARD PRACTICE FOR METHOD OF CLOSING, SEALING AND REINFORCING FIBERBOARD SHIPPING CONTAINERS. ADDITIONAL INFORMATION FOR KK-L-2004 WITH INTERIM CHANGES BELOW: FEDERAL SPECIFICATION KK-L-2004, DATED 22 APRIL, 1989 IS HEREBY CANCELED. THIS DOCUMENT HAS BEEN SUPERSEDED BY MIL-DTL-32092 LEATHER, CATTLEHIDE, DEERSKIN AND HORSEHIDE, CHROME TANNED, Nov. 8, 2001. (ref. T0731 - 5/23/06) ADDITIONAL INFORMATION FOR MIL-B-286:. NO ADDITIONAL INFORMATION FOLLOWS.. INTERIM CHANGES TO MIL-DTL-10884H: PAGE 1, PARA. 1.2, CLASSIFICATION. AFTER "FINISH 5" ADD "FINISH 6 - WHITE". PAGE 8, PARA. 3.4.5, DELETE SENTENCES 4 AND 5 IN THEIR ENTIRETY. PAGE 8, AFTER PARA. 3.4.5, ADD NEW PARA. AS FOLLOWS: "3.4.6 FINISH 6 - WHITE. REFERENCE PARA. 3.4.5 EXCEPT THE COLOR SHALL BE WHITE." ADDITIONAL INFORMATION FOR MIL-G-16491: MIL-G-16491F IS CANCELLED - REPLACED BY NASM 16491. (ref. T1232 - 6/6/06) ADDITIONAL INFORMATION FOR DD 81337 2-1-522:. NO ADDITIONAL INFORMATION FOLLOWS.
 

Web Link

FBO.gov Permalink
(https://www.fbo.gov/spg/DLA/J3/DSCP-C/spe1c115q0159/listing.html)
 

Place of Performance

Address: Clothing & Textile, Gloves/Wet Weather Team DLA TROOP SUPPORT, 700 Robbins Ave./Bldg 3A-4194, Philadelphia, Pennsylvania, 19111-5096, United States

Zip Code: 19111-5096
 

Record

SN03604144-W 20141225/141223235239-868eb23bf571333131a16f313ff71712 (fbodaily.com)
 

Source

FedBizOpps Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's FBO Daily Index Page |