MODIFICATION
66 -- HELIUM STORAGE TANK
- Notice Date
- 4/13/2015
- Notice Type
- Modification/Amendment
- NAICS
- 339999
— All Other Miscellaneous Manufacturing
- Contracting Office
- Department of Commerce, National Institute of Standards and Technology (NIST), Acquisition Management Division, 100 Bureau Drive, Building 301, Room B130, Gaithersburg, Maryland, 20899-1410, United States
- ZIP Code
- 20899-1410
- Solicitation Number
- SB1341-15-RQ-0232
- Archive Date
- 5/14/2015
- Point of Contact
- Lynda M Roark, Phone: 3019753725, Patrick K Staines, Phone: (301)975-6335
- E-Mail Address
-
Lynda.Roark@nist.gov, patrick.staines@nist.gov
(Lynda.Roark@nist.gov, patrick.staines@nist.gov)
- Small Business Set-Aside
- Total Small Business
- Description
- AMENDMENT 0002: The purpose of this amendment is to answer questions. Question 1): Per ASME, Section VIII Div 1 the Manufacturer is responsible to material verification. Will the government be provided Material Test Reports, Partial Data Reports for the government supplied parts? Answer: The government will maintain the material certs for the government supplied assemblies. Question 2): Scope of Work, Section 2.8 states, "Do not paint stainless steel surfaces...." Does the government expect any of the non supplied attachments (lugs, nozzles, couplings, etc.) to be Stainless Steel? Answer: Only the four government supplied assemblies need to be stainless steel. Question 3): Section 3.3, subpart calls for the internal Stiffeners Rings to be Stainless Steel Angle. Are these the same Stiffeners identified on drawing 002-3727 #2 as SA 516 GR 70? If so, please clarify which material it is and are these supplied or the manufacturers responsibility to fabricate? Answer: NCNR Drawing 002-3727 is correct, Section 3.3 is in error, stiffeners will be steel, not stainless steel. Question 4): Section 5.0, please identify where on the government supplied drawings where the Pressure Transmitter Support Bracket, the Government Supplied Sub-Assemblies and the listed material are to be located on the tank. Answer: NCNR Drawing 002-2936 Sheet 1, Section A-A shows the position of the four government supplied assemblies. On the BOM: Item 1, 002-2938 Item 2, 002-2939 Item 3, 002-2940 Item 4, 002-2937 *Note position of the four government supplied assemblies are referenced to Item 13, Bottom Lifting Lug. Question 5): Scope of Work section 2, ¶ 2.10 it states "The contractor is responsible for final placement of the storage tank on the existing cement pad." Is a site map with the location of the existing pad available in order to determine access and what type of equipment will be required to set the vessel on the pad as well as learning how close the transport vehicle will be able to get to the site? Answer: There will be no surprises, the pad is right next to the back road, it will be very easy to get a crane in to put it in place. The pads for rigging it to the crane and are set so the vessel can easy be lifted into place without any special effort. All other terms remain unchanged.
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DOC/NIST/AcAsD/SB1341-15-RQ-0232/listing.html)
- Place of Performance
- Address: 100 Bureau Drive, Gaithersburg, Maryland, 20899, United States
- Zip Code: 20899
- Zip Code: 20899
- Record
- SN03698128-W 20150415/150413235242-d904f9865ad3238267ff5ca5c8e5a0f3 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |