SOLICITATION NOTICE
47 -- HOSE, AIR BREATHING
- Notice Date
- 6/4/2015
- Notice Type
- Combined Synopsis/Solicitation
- NAICS
- 332999
— All Other Miscellaneous Fabricated Metal Product Manufacturing
- Contracting Office
- Defense Logistics Agency, DLA Acquisition Locations, DLA Land and Maritime, P O Box 3990, Columbus, Ohio, 43218-3990, United States
- ZIP Code
- 43218-3990
- Solicitation Number
- SPE7M415Q0317
- Archive Date
- 7/4/2015
- Point of Contact
- Lori C. Phillips, Phone: 6146927453
- E-Mail Address
-
Lori.phillips@Dla.MIl
(Lori.phillips@Dla.MIl)
- Small Business Set-Aside
- Total Small Business
- Description
- HOSE, AIR DUCT (AIR BREATHING). Size 2, low pressure, flexible hose, mustard gas resistant, nominal length 6 feet NSN 4720-00-279-0093 QUANTITY 7,282 EA THIS ITEM HASTECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS OF STATEOR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL AGREEMENTS. TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345,"MILITARY CRITICAL TECHNICAL DATA AGREEMENT," FORM IS AVAILABLE AT THE WORLD WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BYWRITING TO: DLA LOGISTICS INFORMATION SERVICE FEDERAL CENTER 74 WASHINGTON AVE., NORTH BATTLE CREEK, MI 49037-3084 TO MANUFACTURETHIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCEAGREEMENT, DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THEOFFER, UNLESS AN EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 "EXEMPTIONS OF GENERAL APPLICABILITY," AND/OR EAR PART 740ARE APPLICABLE. NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL DATA ARE REQUIRED TO PROVIDE THE CONTRACTINGOFFICER WITH AN APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO RECEIVE A COPY OF THE EXPORT CONTROLLEDTECHNICAL DATA. NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO THEIR DD FORM 2345 CERTIFICATION MAY NOTFURTHER DISSEMINATE SUCH DATA UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY PERMITTED BY DODD5230.25." 52.246-11 Higher Level Contract Quality Requirement (Manufacturers) FAR CLAUSE 52.246-11 APPLIES. A QUALITYMANAGEMENT PROGRAM MEETING THE REQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008 (EXAMPLE SAE AS 9100), THEFOLLOWING TAILORED VERSION OF ISO 9001:2008; OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008 (EXAMPLE SAE AS 9003)IS REQUIRED. MIL-I-45208 AND MIL-Q-9858 ARE OBSOLETE AND NO LONGER CONSIDERED SUITABLE WHEN HIGHER LEVEL QUALITY IS REQUIRED. IN THE TAILORED VERSION OF THE ISO 9001:2008, ANY REFERENCES WHICH CITE THE ENTIRE INTERNATIONAL STANDARD ARE INTERPRETED AS EXCLUSIONS TO THIS DOCUMENT. DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008 4.1 General requirements, [excluding reference to 1.2and excluding NOTE 4.2.1 General, [excluding subparagraph a)] 4.2.2 Quality manual, [excluding subparagraph a)] 4.2.3 Controlof documents 4.2.4 Control of records 5.1 Management commitment 5.3 Quality policy 6.2.2 Competence, training and awareness 6.4 Work environment 7.1 Planning of product realization, [excluding NOTE 2] 7.2.1 Determination of requirements related to theproduct 7.2.2 Review of requirements related to the product 7.2.3 Customer communication 7.4.1 Purchasing process 7.4.3 Verification of purchased product 7.5.1 Control of production and service provision 7.5.3 Identification and traceability 7.5.4 Customerproperty 7.5.5 Preservation of product 7.6 Control of monitoring and measuring equipment 8.1 General, [excluding subparagraph b) and subparagraph c)] 8.2.2 Internal audit 8.2.4 Monitoring and measurement of product 8.3 Control of nonconforming product 8.5.2Corrective action 8.5.3 Preventive action GOVERNMENT/CONTRACTOR FAT, PACKAGING FAT and GOVERNMENT/CONTRACTOR PLT IS REQUIREDIAW SQAP002790093. DESTRUCTIVE TESTING APPLIES. The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply tothis procurement. Review the Technical Data Package (TDP) for additional information. Contractor First Article Test Report Production Lot Acceptance Test Report Certificate of Conformance Quality Program Plan CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NORINCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOESNOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BYTHE SPECIFICATION REQUIREMENTS. The following Engineering Exceptions shall apply to this procurement: Drawing 81361 5-19-916-2,Product Data Management System Technical Data Package List, Valid from 2/25/15 to 2/25/16, page 2, Drawing number MIL-DTL-14506, REV SYM 'H' should be changed to 'J'. ANSI MH1 can be obtained on the Material Handler's of America's website, www.mhi.org, referenced simply as MH1. Standard is available at no cost but free registration on the site is required to obtain. THIS SHELF LIFE ITEM ISNON-EXTENDABLE, CODE S, WITH A TOTAL SHELF LIFE OF SIXTY MONTHS. MATERIAL FURNISHED UNDER THIS CONTRACT/ORDER SHALL HAVE AT LEAST85% (51 MONTHS) OF SHELF LIFE REMAINING AT TIME OF DELIVERY. SHELF LIFE MARKINGS REQUIRED PER 5.10.1 OF MIL-STD-129: SHELF-LIFEMARKINGS SHALL BE SHOWN AS PART OF THE ITEM IDENTIFICATION DATA ON UNIT PACKS, INTERMEDIATE CONTAINERS, EXTERIOR CONTAINERS,AND UNPACKED ITEMS. SHELF-LIFE MARKINGS SHALL INCLUDE THE CURED DATE AND THE EXPIRATION DATE. THE EXPIRATION DATE SHALL BECALCULATED FROM THE CURED DATE OF THE RUBBER/ELASTOMER. FULL AND OPEN COMPETITION APPLY This is an identified Chemical Biological Defense Equipment item. All requests for waivers or deviations, both pre and post award, must be approved by theappropriate Joint Program Executive Office for Chemical and Biological Defense (JPEO-CBD) ESA prior to final approval. All packaged items of supply shall be marked IAW MIL-STD-129. Requirements defining levels of pack shall be IAW MIL-STD-2073-1. If militarypackaging is required and Special Packaging Instructions (SPI) are provided in the technical data package (TDP), then the packaging shall be IAW the provided SPI. CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 81361 5-19-916 REVISION NR AD DTD01/22/2015 PART PIECE NUMBER: C5-19-916-2 IAW REFERENCE SPEC NR MIL-DTL-14506J REVISION NR J DTD 10/03/2006 PART PIECENUMBER: IAW REFERENCE STD NR MIL-STD-129R REVISION NR R DTD 10/03/2006 PART PIECE NUMBER: TYPE I SHELF LIFE, 60 MONTHS IAWREFERENCE NON GOVT STD ASTM D2000-12 REVISION NR 12 DTD 02/14/2012 PART PIECE NUMBER: IAW REFERENCE NON GOVT STD SAEAMS-QQ-W-428A REVISION NR DTD 10/07/2006 PART PIECE NUMBER: IAW REFERENCE QAP 16236 SQAP002790093 REVISION NR F DTD05/11/2015 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 81361 5-19-916-2 REVISION NR DTD 02/25/2015 PART PIECE NUMBER: IAWREFERENCE DRAWING NR 81361 5-19-916-2 REVISION NR A DTD 04/07/2014 PART PIECE NUMBER: IAW REFERENCE QAP 16236CDRL-ECBCPLTC-15062 REVISION NR DTD 03/03/2015 PART PIECE NUMBER: IAW REFERENCE QAP 16236 CDRL-ECBCCOC-15062 REVISION NRDTD 03/03/2015 PART PIECE NUMBER: IAW REFERENCE QAP 16236 CDRL-ECBCFATC-15062 REVISION NR DTD 03/03/2015 PART PIECENUMBER: IAW REFERENCE QAP 16236 CDRL-ECBCQPP-15062 REVISION NR DTD 03/03/2015 PART PIECE NUMBER: PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999 QUP:001 PRES MTHD:ZZ CLNG/DRY:Z PRESV MAT:ZZ WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNNTHKNESS:Z UNIT CONT:ZZ OPI:A INTRMDTE CONT:ZZ INTRMDTE CONT QTY:ZZZ PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITHMIL-STD-129. SPECIAL MARKING CODE:32 -32 Type I, shelf life PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY01, 2008 DM_15_002790093 - DATE:-12 FEB 2015 NSN:4720-00-279-0093 PRESERVATION: MILITARY LEVEL OF PACKING: -B-- QUANTITY PERUNIT PACKAGE: -001- SPI NUMBER P5-19-916-2, Rev A, Date 7 APR 2014- PLACE A RED X AND THE WORDS"SHORT BOX" ON THE FRONT OF ANY BOXTHAT HAS A SHORT QUANTITY, THEN PLACE THAT BOX/BOXES WITH THE MARKINGS SHOWING ON THE TOP FRONT OF THE PALLET LOAD. Certificates of Conformances (see CDRL for COC format IAW DI-MISC-81356A) are required for all material and shall be submitted as part of the First Article Test report (FATR). COC's are also required for packaging materials. The contractor is responsible for all inspections and testing regardless of who conducts the actual testing. A packaging FAT is required and shall consist of three (3) packaged unitsinspected IAW SPI P5-19-916-2. THIS SHELF LIFE ITEM IS NON-EXTENDABLE, CODE S, WITH A TOTAL SHELF LIFE OF SIXTY MONTHS. MATERIALFURNISHED UNDER THIS CONTRACT/ORDER SHALL HAVE AT LEAST 85% (51 MONTHS) OF SHELF LIFE REMAINING AT TIME OFDELIVERY. SHELF LIFE MARKINGS REQUIRED PER 5.10.1 OF MIL-STD-129: SHELF-LIFE MARKINGS SHALL BE SHOWN AS PART OF THE ITEM IDENTIFICATION DATA ON UNIT PACKS, INTERMEDIATE CONTAINERS, EXTERIOR CONTAINERS, AND UNPACKED ITEMS. SHELF-LIFE MARKINGS SHALL INCLUDE THE CURED DATE AND THE EXPIRATION DATE. THE EXPIRATION DATE SHALL BE CALCULATED FROM THE CURED DATE OF THERUBBER/ELASTOMER. PARCEL POST ADDRESS: W25G1U W1BG DLA DISTRIBUTION DDSP NEW CUMBERLAND FACILITY 2001 NORMANDY DRIVE DOOR 113 TO 134 NEW CUMBERLAND PA 17070-5002 US FREIGHT SHIPPING ADDRESS: W25G1U W1BG DLA DISTRIBUTION DDSP NEW CUMBERLAND FACILITY 2001 NORMANDY DRIVE DOOR 113 TO 134 NEW CUMBERLAND PA 17070-5002 US
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DLA/J3/DSCC/SPE7M415Q0317/listing.html)
- Place of Performance
- Address: DLA LAND AND MARITIME, FLUID HANDLING DIVISION, P O BOX 3990, COLUMBUS, Ohio, 43218-3990, United States
- Zip Code: 43218-3990
- Zip Code: 43218-3990
- Record
- SN03752853-W 20150606/150604235205-fa577aabe8f5e9330149ff3db7bd8378 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |