SOURCES SOUGHT
17 -- Spear Water Break - Market Survey
- Notice Date
- 6/10/2015
- Notice Type
- Sources Sought
- NAICS
- 488190
— Other Support Activities for Air Transportation
- Contracting Office
- Defense Logistics Agency, DLA Acquisition Locations, DLA Land and Maritime - BSM, P O Box 3990, Columbus, Ohio, 43216-5000, United States
- ZIP Code
- 43216-5000
- Solicitation Number
- SPM7M215R0070
- Archive Date
- 6/10/2016
- Point of Contact
- jana m engels-stinson, Phone: 6146921582
- E-Mail Address
-
jana.engels-stinson@dla.mil
(jana.engels-stinson@dla.mil)
- Small Business Set-Aside
- N/A
- Description
- Market Survey This is a Sources Sought Notice and is for information purposes only. THIS IS NOT A REQUEST FOR PROPOSALS, QUOTATIONS, OR BIDS. All of the following information is approximate and may be altered in the actual solicitation. Responses to this sources sought announcement will be used by the Government to make appropriate acquisition decisions. DLA Land and Maritime anticipates issuing a solicitation in the near future for approximately 24 each of NSN 1710-00-171-2152,16 ea to be shipped to New Cumberland PA 17070 and 8 ea to be shipped to San Diego CA 92136-5491 Item is to be manufactured I/A/W THE FOLLOWING: SPEAR WATER BRAKE MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL NOT BE INTENTIONALLY ADDED TO,OR COME IN DIRECT CONTACT WITH,ANY HARDWARE OR SUPPLIES FURNISHED UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS; AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA. PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR MERCURY COMPOUND. (IAW NAVSEA 5100-003D). 82N CSI ALRE Dwg-80020-14-50700 (Rev W) DWG-16236-CN001712152 QAP-16236-SQAP0017121527FAT QAP-16236-SQAP001712152QA QAP-80020-CDRL-15-12036PTI QAP-80020-CDRL-15-12036COQC QAP-80020-CDRL-15-12036FAT AIRCRAFT LAUNCH AND RECOVERY EQUIPMENT (ALRE). CRITICAL APPLICATION ITEM. ALL REQUESTS FOR WAIVERS OR DEVIATIONS CLASSIFIED AS CRITICAL, MAJOR, OR MINOR MUST BE FORWARDED TO THE DSC CONTRACTING OFFICER FOR REVIEW AND APPROVAL. ALL ITEMS OF SUPPLY SHALL BE MARKED IAW MIL-STD-129. IN ADDITION, EACH UNIT PACK WILL BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE), CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S CAGE CODE AND PART NUMBER. PCO MANDATORY INSPECTION. DURING PRODUCTION, MANDATORY INSPECTION IS REQUIRED TO BE CCOMPLISHED AND DOCUMENTED BY THE CONTRACTOR AS FOLLOWS: CRITICAL AND MAJOR CHARACTERISTICS AS IDENTIFIED IN CLASSIFICATION OF CHARACTERISTICS BLOCK ON DRAWING(S), TECHNICAL SPECIFICATIONS, SECOND TIER DOCUMENTS REFERENCED IN THE ACQUISITION ITEM DESCRIPTION AND SPECIFIED IN THE PROCUREMENT DOCUMENT, AND CHARACTERISTICS DEFINED AS: (A) MATERIAL CERTIFICATIONS (B) DESTRUCTIVE AND / OR NONDESTRUCTIVE TEST RESULTS (WHEN APPLICABLE) (C) ATTRIBUTES FOR PLATING HARDNESS IMPORTANT MINOR CHARACTERISTICS SHALL BE DEFINED BY THE CONTRACTOR SUBJECT TO QAR CONCURRENCE, UNLESS OTHERWISE DEFINED ON APPLICABLE DRAWING(S), SPECIFICATIONS AND CHARRACTERISTICS DEFINED AS: (A) DIAMETRICAL AND LINEAR DIMENSIONS HAVING A TOLERANCE OF +/- 0.005 INCH OR LESS (B) GEOMETRIC FEATURE CONTROLS HAVING A TOTAL TOLERANCE OF 0.003 INCH OR LESS (C) SURFACE FINISHES HAVING A 16 VALUE OR LESS (D) CLASS THREE THREADS (E) ANGULAR TOLERANCES WITH A TOTAL RANGE LESS THAN 1 DEGREE LEVEL OF INSPECTION: ANSI / ASQC Z1.4 FOR SINGLE SAMPLING USING A GENERAL INSPECTION LEVEL O II (A) CRITICAL AND MAJOR CHARACTERISTICS: 100% INSPECTION APPLIES (B) IMPORTANT MINOR CHARACTERISTICS: AQL OF 1.5 CERTIFICATION / DATA REPORTS: THE CONTRACTOR IS RESPONSIBLE FOR PREPARING A CERTIFICATE OF QUALITY COMPLIANCE (COQC) IN ACCORDANCE WITH THE DD FORM 1423 CONTRACT DATA REQUIREMENTS LIST (CDRL). THE COQC CONTENT WILL INCLUDE AS A MINIMUM THE DATA DESCRIBED IN DLAR CLAUSE 52.246-9000, IN ADDITION TO ALL PCO MANDATORY INSPECTION RESULTS. THIS COQC REQUIREMENT APPLIES TO EACH UNIT OF CONTRACT QUANTITY. CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. 52.246-11 Higher Level Contract Quality Requirement (Manufacturers) FAR CLAUSE 52.246-11 APPLIES. A QUALITY MANAGEMENT PROGRAM MEETING THE REQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008 (EXAMPLE SAE AS 9100), THE FOLLOWING TAILORED VERSION OF ISO 9001:2008; OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008 (EXAMPLE SAE AS 9003) IS REQUIRED. MIL-I-45208 AND MIL-Q-9858 ARE OBSOLETE AND NO LONGER CONSIDERED SUITABLE WHEN HIGHER LEVEL QUALITY IS REQUIRED. IN THE TAILORED VERSION OF THE ISO 9001:2008, ANY REFERENCES WHICH CITE THE ENTIRE INTERNATIONAL STANDARD ARE INTERPRETED AS EXCLUSIONS TO THIS DOCUMENT. DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008 4.1 General requirements, [excluding reference to 1.2 and excluding NOTE 3 c)] 4.2.1 General, [excluding subparagraph a)] 4.2.2 Quality manual, [excluding subparagraph a)] 4.2.3 Control of documents 4.2.4 Control of records 5.1 Management commitment 5.3 Quality policy 6.2.2 Competence, training and awareness 6.4 Work environment 7.1 Planning of product realization, [excluding NOTE 2] 7.2.1 Determination of requirements related to the product 7.2.2 Review of requirements related to the product 7.2.3 Customer communication 7.3.7 Control of design and development changes 7.4.1 Purchasing process 7.4.3 Verification of purchased product 7.5.1 Control of production and service provision 7.5.3 Identification and traceability 7.5.4 Customer property 7.5.5 Preservation of product 7.6 Control of monitoring and measuring equipment 8.1 General, [excluding subparagraph b) and subparagraph c)] 8.2.2 Internal audit 8.2.4 Monitoring and measurement of product 8.3 Control of nonconforming product 8.5.2 Corrective action 8.5.3 Preventive action THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL AGREEMENTS. TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, "MILITARY CRITICAL TECHNICAL DATA AGREEMENT," FORM IS AVAILABLE AT THE WORLD WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO: DLA LOGISTICS INFORMATION SERVICE FEDERAL CENTER 74 WASHINGTON AVE., NORTH BATTLE CREEK, MI 49037-3084 TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT, DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 "EXEMPTIONS OF GENERAL APPLICABILITY," AND/OR EAR PART 740 ARE APPLICABLE. NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL DATA ARE REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO RECEIVE A COPY OF THE EXPORT CONTROLLED TECHNICAL DATA. NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY PERMITTED BY DODD 5230.25." REMINDER: THIS IS A CRITICAL ITEM AND ALL MAJOR AND MINOR WAIVER/DEVIATION REQUESTS MUST BE FORWARDED TO THE DSCC CONTRACTING OFFICER WHO WILL COORDINATE THE REVIEW AND APPROVAL THROUGH THE RESPONSIBLE ENGINEERING SERVICE ACTIVITY. NOTE: THIS IS A RESTRICTED SOURCE ITEM AND REQUIRES ENGINEERING SOURCE APPROVAL BY THE GOVERNMENT DESIGN CONTROL ACTIVITY. "CERTIFICATE OF QUALITY COMPLIANCE IS MANDATORY" THIS MATERIAL MUST MEET NAVAIR AIRCRAFT LAUNCH & RECOVERY EQUIPMENT TRACEABILITY REQUIREMENTS. BARE ITEM MARKINGS SHALL BE IAW THE TECHNICAL DATA DRAWINGS PROVIDED. BARE ITEM MATERIAL SHALL BE MARKED WITH CONTRACT NUMBER, NAWC CAGE, AND PART NUMBER UNLESS OTHERWISE SPECIFICIED ON ASSOCIATED DRAWING. IF A CONFLICT EXISTS WITH MARKING REQUIREMENTS OF THIS 82N ALRE/SE ITEM, THE ASSOCIATED DRAWING REQUIREMENTS SHALL APPLY. DLAD PROVISION 52.211-9009 IS APPLICABLE TO THIS SOLICITATION, THEREFORE SURPLUS MATERIAL WILL NOT BE CONSIDERED. IF PRESENT IN THE SOLICITATION, PROVISION 52.211-9003 AND CLAUSE 52.211-9000 ARE NOT APPLICABLE. CRITICAL APPLICATION ITEM CLOVER INDUSTRIES, INC. DBA 45X91 P/N 14-50700-5 HAMILL MANUFACTURING COMPANY DBA 17661 P/N 14-50700-5 WELLMAN DYNAMICS MACHINING AND 6JRD9 P/N 14-50700-5 IAW REFERENCE DRAWING NR 80020 MPR45 REVISION NR C DTD 03/24/1987 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 14-50700 REVISION NR W DTD 03/12/2012 PART PIECE NUMBER: 14-50700-5 IAW REFERENCE DRAWING NR 80020 14-41941 REVISION NR H DTD 02/23/2010 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 16236 CN001712152 REVISION NR DTD 04/15/2015 PART PIECE NUMBER: IAW REFERENCE QAP 16236 SQAP001712152QA REVISION NR DTD 04/13/2015 PART PIECE NUMBER: IAW REFERENCE QAP 16236 SQAP001712152CFAT REVISION NR DTD 4/15/2015 PART PIECE NUMBER: IAW REFERENCE QAP 80020 CDRL-15-12036CQOC/28APRIL2015 REVISION NR DTD 03/20/2015 PART PIECE NUMBER: IAW REFERENCE QAP 80020 CDRL-15-12036PIT/28APRIL2015 REVISION NR DTD 03/20/2015 PART PIECE NUMBER: IAW REFERENCE QAP 80020 CDRL-15-12036FAT/28APRIL2015 REVISION NR DTD 03/20/2015 PART PIECE NUMBER: PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999 QUP:001 PRES MTHD:BL CLNG/DRY:1 PRESV MAT:49 WRAP MAT:GB CUSH/DUNN MAT:AD CUSH/DUNN THKNESS:R UNIT CONT:FC OPI:M PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:ZZ -ZZ Special Requirements PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008 EACH UNIT PACKAGE WILL BE MARKED WITH THE NSN, CONTRACT NUMBER, LOT NUMBER, CONTRACTOR CAGE CODE, MANUFACTURER CAGE CODE, AND PART NUMBER. EXPORT CONTROLLED ITEM. SPECIAL MARKINGS CODE 40 REQUIRED PER MIL-STD-129, PARAGRAPH 4.4.3.14 APPLIES This solicitation is anticipated to require FOB Destination, Inspection and Acceptance at Origin. Please see attached Market Survey. All interested parties are invited to express your interest in this procurement by 6-19-15.
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DLA/J3/DSCC-BSM/SPM7M215R0070/listing.html)
- Record
- SN03760579-W 20150612/150611000123-a6c5fbbe59949d467f7b1adc633f3c91 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |