FBODaily.com | FedBizOpps: SRCSGT | 25 | SEAT, VEHICULAR AND TARPAULIN

FBO DAILY - FEDBIZOPPS ISSUE OF SEPTEMBER 30, 2015 FBO #5059
SOURCES SOUGHT

25 -- SEAT, VEHICULAR AND TARPAULIN

Notice Date: 9/28/2015
Notice Type: Sources Sought
NAICS: 314910 — Textile Bag and Canvas Mills
Contracting Office: Defense Logistics Agency, DLA Acquisition Locations, DLA Land and Maritime, P O Box 3990, Columbus, Ohio, 43218-3990, United States
ZIP Code: 43218-3990
Solicitation Number: SPE7MX-16-R-0007
Archive Date: 10/20/2015
Point of Contact: Pamela R. Baker, Phone: 6146926629
E-Mail Address: Pamela.Baker@dla.mil
(Pamela.Baker@dla.mil)
Small Business Set-Aside: N/A
Description: *** LTC PID Packaging Consolidated Text *** PLEASE SEE GLOSSARY AT THE END OF THE DOCUMENT FOR FULL TEXT OF THE ITEM DESCRIPTION AND PACKAGING REFERENCE NUMBERS CALLED OUT FOR EACH NSN. NSN:006537589 TARPAULIN (12 FT X 12 FT, GREEN). REFERENCE NUMBER:ZD080 MANUFACTURE PER DRAWING 6537589 & MIL-PRF-20696 IN LIEU OF MIL-C-10632. HEAT SEALED FABRIC SEAMS (SECTION A - A) MAY BE USED. HEAT SEALED FABRIC SEAMS SHALL BE CONTIN- UOUS AND SHALL EXTEND OVER THE ENTIRE AREA OF OVERLAPPING FABRIC INTERSECTIONS. FABRIC AT THE HEAT SEALED SEAMS SHALL MEET OR EXCEED THE VALUES FOR BREAKING STRENGTH AND COATING ADHE- SION SPECIFIED FOR THE BASE COATED FABRIC MATERIAL,ALSO IN LIEU P/N 8407338 USE 7979453. REFERENCE NUMBER:ZD059 REFERENCE NUMBER:CS060 REFERENCE NUMBER:CA070 REFERENCE NUMBER:CS086 REFERENCE NUMBER:CQC06 CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 19200 6537589 REVISION NR D DTD 10/25/1991 PART PIECE NUMBER: 6537589 IAW REFERENCE DRAWING NR 19207 7979453 REVISION NR E DTD 08/17/1989 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12355846 REVISION NR F DTD 04/04/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 8407336 REVISION NR H DTD 09/20/2006 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 8407338 REVISION NR K DTD 09/20/2006 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8407336 REVISION NR H DTD 09/23/2006 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8407338 REVISION NR K DTD 09/23/2006 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 7359274 REVISION NR K DTD 11/22/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 6537589 REVISION NR DTD 02/10/2011 PART PIECE NUMBER: PREP FOR DELIVERY LINE ITEM 00001 TYPE OF COVERAGE: DLA DIRECT, CONUS PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999 QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00 WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0 UNIT CONT:E5 OPI:O PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:00 -00 No special marking PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008 NSN:015507246 SEAT, VEHICULAR. PICATINNY SEAT ASSEMBLY. REFERENCE NUMBER:ZD080 REFERENCE NUMBER:ZD059 CONTRACTOR FAT APPLIES. PER FAR 52.209-3: (A) THE CONTRACTOR SHALL TEST _5__UNIT(S)# (B) THE CONTRACTOR SHALL SUBMIT THE FAT REPORT WITHIN__60___CALENDAR DAYS# (NOTE: THE DELIVERY SCHEDULE ON THE FACE OF THE SOLICITATION REFLECTS ONLY THE TIME TO DELIVER THE SUPPLIES.) WITHIN _30__ CALENDAR DAYS AFTER THE GOVERNMENT RECEIVES THE FIRST ARTICLE THE CONTRACTING OFFICER SHALL NOTIFY# PER DLAD 52.209-9017, ALT III DISPOSITION OF FIRST ARTICLES: *SEE FAR 52.209-3 (E), THE CONTRACTOR MAY DELIVER THE APPROVED FIRST ARTICLE AS PART OF THE CONTRACT QUANTITY. AFTER RECEIPT OF QUOTES, OFFERORS MAY BE CONTACTED TO PRICE THE FAT REQUIREMENT. PRODUCT VERIFICATION TESTING (PVT) CLAUSE DLAD 52.246-9004 MAY BE INVOKED FOR THE REFERENCED CONTRACT. ------------------------------------------------- CLARIFICATION TO DRAWING 13015467: MATERIAL TYPE FOR A-A-55126B SHALL BE TYPE II, CLASS 1. EXCEPTION TO DRAWINGS 13015468 AND 13015469: SUGGESTED SOURCE OF SUPPLY FOR FOAM: BERGAD INCORPORATED 747 ELJER WAY FORD CITY, PA 16226 888.476.8664 -------------------------------------------------- REFERENCE NUMBER:CQ043 REFERENCE NUMBER:CQ044 REFERENCE NUMBER:CS001 REFERENCE NUMBER:CS187 REFERENCE NUMBER:CS086 REFERENCE NUMBER:CQ026 REFERENCE NUMBER:CQ023 CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 19200 13014413 REVISION NR F DTD 10/15/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12579607 REVISION NR C DTD 08/04/2009 PART PIECE NUMBER: IAW REFERENCE UNK QPL-16173-84 NOT 1 REVISION NR 84 DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE QAP 19200 12993884 REVISION NR F DTD 08/15/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015465 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015466 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015467 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015468 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015469 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015470 REVISION NR B DTD 06/10/2010 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015471 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015472 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015473 REVISION NR DTD 11/01/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015474 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015476 REVISION NR B DTD 06/10/2010 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015477 REVISION NR DTD 11/01/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015478 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015479 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015480 REVISION NR DTD 11/01/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015481 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015482 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015483 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015484 REVISION NR DTD 11/01/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015485 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015486 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015487 REVISION NR B DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015488 REVISION NR DTD 11/01/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015489 REVISION NR DTD 03/06/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13015490 REVISION NR A DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L10S3028-13015470 REVISION NR A DTD 05/21/2010 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L10S3028-13015476 REVISION NR A DTD 05/21/2010 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13014413 REVISION NR DTD 12/11/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13014413 REVISION NR DTD 01/04/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13014413 REVISION NR E DTD 03/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12993884 REVISION NR G DTD 07/18/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13014413 REVISION NR DTD 05/20/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13014413 REVISION NR DTD 05/01/2014 PART PIECE NUMBER: PREP FOR DELIVERY LINE ITEM 00002 TYPE OF COVERAGE: DLA DIRECT, CONUS PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999 QUP:001 PRES MTHD:ZZ CLNG/DRY:Z PRESV MAT:ZZ WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:Z UNIT CONT:ZZ OPI:A INTRMDTE CONT:ZZ INTRMDTE CONT QTY:ZZZ PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:ZZ -ZZ Special Requirements PACKAGING SHALL BE IN ACCORDANCE WITH SPECIAL PACKAGING INSTRUCTION 13014413. ************************************************************************************************************ GLOSSARY ************************************************************************************************************ PACKAGING TEXT THE FOLLOWING PARAGRAPH APPLIES TO ALL PACKAGING CALLED OUT IN THIS DOCUMENT: ITEM DESCRIPTION TEXT REFERENCE NUMBER ZD080 SAMPLING: IF THE APPLICABLE (OEM OR MILITARY) DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES AN ACCEPTABLE QUALITY LEVEL (AQL), IT MAY BE USED TO ESTABLISH THE AUTHORIZED SAMPLE SIZE. HOWEVER THE SAMPLING ACCEPTANCE NUMBER SHALL BE REDUCED TO ZERO (0). EVEN THOUGH THE ACCEPTANCE LEVEL IS ELIMINATED, THE SAMPLE SIZE REMAINS THE SAME. UNLESS OTHERWISE SPECIFIED IN THE OEM OR MILITARY DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISIONS (QAPs) CHARACTERISTICS CLASSIFIED AS CRITICAL, MAJOR AND MINOR SHALL HAVE AN ASSIGNED AQL OF 0.10, 1.0, AND 4.0 RESPECTIVELY. ASQ H1331 TABLE 1 OR MIL-STD-1916 SHALL TAKE PRECEDENCE OVER MIL-STD-105 AND ASQ Z1.4. THESE PLANS ACCEPT ON ZERO DEFECTS AND REJECT THE ENTIRE LOT ON ONE DEFECT. A ZERO BASED SAMPLING PLAN SHALL BE USED, UNLESS OTHERWISE SPECIFIED BY CONTRACT. REFERENCE NUMBER ZD059 52.246-11 Higher Level Contract Quality Requirement (Manufacturers) FAR CLAUSE 52.246-11 APPLIES. A QUALITY MANAGEMENT PROGRAM MEETING THE REQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008 (EXAMPLE SAE AS 9100), THE FOLLOWING TAILORED VERSION OF ISO 9001:2008; OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008 (EXAMPLE SAE AS 9003) IS REQUIRED. MIL-I-45208 AND MIL-Q-9858 ARE OBSOLETE AND NO LONGER CONSIDERED SUITABLE WHEN HIGHER LEVEL QUALITY IS REQUIRED. IN THE TAILORED VERSION OF THE ISO 9001:2008, ANY REFERENCES WHICH CITE THE ENTIRE INTERNATIONAL STANDARD ARE INTERPRETED AS EXCLUSIONS TO THIS DOCUMENT. DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008 4.1 General requirements, [excluding reference to 1.2 and excluding NOTE 3 c)] 4.2.1 General, [excluding subparagraph a)] 4.2.2 Quality manual, [excluding subparagraph a)] 4.2.3 Control of documents 4.2.4 Control of records 5.1 Management commitment 5.3 Quality policy 6.2.2 Competence, training and awareness 6.4 Work environment 7.1 Planning of product realization, [excluding NOTE 2] 7.2.1 Determination of requirements related to the product 7.2.2 Review of requirements related to the product 7.2.3 Customer communication 7.3.7 Control of design and development changes 7.4.1 Purchasing process 7.4.3 Verification of purchased product 7.5.1 Control of production and service provision 7.5.3 Identification and traceability 7.5.4 Customer property 7.5.5 Preservation of product 7.6 Control of monitoring and measuring equipment 8.1 General, [excluding subparagraph b) and subparagraph c)] 8.2.2 Internal audit 8.2.4 Monitoring and measurement of product 8.3 Control of nonconforming product 8.5.2 Corrective action 8.5.3 Preventive action REFERENCE NUMBER CS060 THE ITEM DESCRIBED IN THIS SOLICITATION IS DEFINED IN WHOLE OR IN PART BY ARMY DRAWING(S). THESE DRAWING(S) MAY CONTAIN A PAINT FINISHING REQUIREMENT. WHERE SUCH REQUIREMENTS ARE SPECIFIED, USE DCSC DRAWING 16236 CS-2300-0001 IN LIEU OF FINISH REQUIRE- MENTS OF THE ARMY DRAWING(S). THIS DRAWING CONTAINS SPECIFICATIONS FOR CHEMICAL AGENT RESISTANT COATINGS (CARC), AND ADDITIONAL INFORMATION RELATING TO HIGH TEMPERATURE COATINGS. REFERENCE NUMBER CA070 FULL AND OPEN COMPETITION APPLY REFERENCE NUMBER CS086 THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH MUST MEET QPL/QML SPECIFICATIONS.BY SUBMITTING AN OFFER, THE OFFEROR AGREES TO PROVIDE QPL/QML COMPONENTS ONLY FROM SOURCES QUALIFIED ON THE APPLICABLE QPL(S)/QML(S). REFERENCE NUMBER CQC06 DLAD 52.246-9000, CERTIFICATE OF QUALITY COMPLIANCE APPLIES. DLAD 52.246-9003, MEASURING AND TEST EQUIPMENT APPLIES. DLAD CLAUSE 52.246-9004, PRODUCT VERIFICATION TESTING, IS HEREBY INCORPORATED, AND MAY BE INVOKED AT THE DISCRETION OF THE PROCUREMENT ACTIVITY IF THIS SOLICITATION/AWARD CALLS FOR GOVERNMENT INSPECTION AT SOURCE. REFERENCE NUMBER CQ043 THIS NSN REQUIRES GOVERNMENT SOURCE INSPECTION WITH A FIRST ARTICLE TEST REQUIREMENT. THE GOVERNMENT SOURCE INSPECTION REQUIREMENT IS VALID ONLY WHEN AN AWARD IS MADE INVOKING THE FIRST ARTICLE TEST REQUIREMENT. IF THE AWARD DOES NOT INCLUDE THE FAT REQUIREMENT, INSPECTION AT DESTINATION IS ACCEPTABLE. REFERENCE NUMBER CQ044 ATTENTION BUYER, FIRST ARTICLE APPROVAL AUTHORITY IS DELEGATED TO DCMA. INCLUDE CLAUSE I09C08 (DELEGATION OF AUTHORITY FOR FIRST ARTICLE APPROVAL) WITH THE AWARD. REFERENCE NUMBER CS001 THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL AGREEMENTS. TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, MILITARY CRITICAL TECHNICAL DATA AGREEMENT, FORM IS AVAILABLE AT THE WORLD WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO: DLA LOGISTICS INFORMATION SERVICE FEDERAL CENTER 74 WASHINGTON AVE., NORTH BATTLE CREEK, MI 49037-3084 TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT, DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 EXEMPTIONS OF GENERAL APPLICABILITY, AND/OR EAR PART 740 ARE APPLICABLE. NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL DATA ARE REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO RECEIVE A COPY OF THE EXPORT CONTROLLED TECHNICAL DATA. NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY PERMITTED BY DODD 5230.25. REFERENCE NUMBER CS187 CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. REFERENCE NUMBER CQ026 "ANY ITEM PREVIOUSLY TESTED BY A VENDOR IN ACCORDANCE WITH *** QUALIFICATION*** REQUIREMENTS (FOR EXAMPLE: FAT, HIGH SHOCK AND/OR VIBRATION TEST), STATED ON DWG, SPECIFICATION, OR STANDARD MAY NOT REQUIRE FURTHER TESTING BY THE SAME VENDOR EXCEPT FOR A LATER CHANGE IN DESIGN, MANUFACTURING PROCEDURES, OR TESTING REQUIREMENTS. A CERTIFICATION OF CONFORMANCE WITH PREVIOUS TEST RESULTS ATTESTING APPLICABILITY SHALL BE SUBMITTED FOR ITEMS PREVIOUSLY TESTED." REFERENCE NUMBER CQ023 PROCESS PROCEDURES AND OR WORKMANSHIP SPECIMENS REQUIRED BY MILITARY SPECIFICATION (S) APPLICABLE TO THIS CONTRACT WILL BE APPROVED BY THE ACTIVITY RESPONSIBLE FOR THE ADMINISTRATION OF THE CONTRACT. POSTAWARD PREPRODUCTION APPROVAL VERIFYING THE REQUIREMENTS OF MIL-DTL-16232 IS REQUIRED.
Web Link: FBO.gov Permalink
(https://www.fbo.gov/spg/DLA/J3/DSCC/SPE7MX-16-R-0007/listing.html)
Record: SN03905994-W 20150930/150928235038-2f4a60e86e1f8ea2c7685227704c2c87 (fbodaily.com)
Source: FedBizOpps Link to This Notice
(may not be valid after Archive Date)

| FSG Index | This Issue's Index | Today's FBO Daily Index Page |

Loren Data's SAM Daily™

25 -- SEAT, VEHICULAR AND TARPAULIN