SOURCES SOUGHT
47 -- hose assembly catapult - market survey
- Notice Date
- 1/13/2016
- Notice Type
- Sources Sought
- NAICS
- 332999
— All Other Miscellaneous Fabricated Metal Product Manufacturing
- Contracting Office
- Defense Logistics Agency, DLA Acquisition Locations, DLA Land and Maritime - BSM, P O Box 3990, Columbus, Ohio, 43216-5000, United States
- ZIP Code
- 43216-5000
- Solicitation Number
- SPE7M216R0004
- Archive Date
- 1/13/2017
- Point of Contact
- jana m engels-stinson, Phone: 6146921582
- E-Mail Address
-
jana.engels-stinson@dla.mil
(jana.engels-stinson@dla.mil)
- Small Business Set-Aside
- N/A
- Description
- Market Survey This is a Sources Sought Notice and is for information purposes only. THIS IS NOT A REQUEST FOR PROPOSALS, QUOTATIONS, OR BIDS. All of the following information is approximate and may be altered in the actual solicitation. Responses to this sources sought announcement will be used by the Government to make appropriate acquisition decisions. DLA Land and Maritime anticipates issuing a solicitation in the near future for approximately 180 each of NSN 4720-01-191-5572 on Solicitation Number SPE7M216R0004. Item will be purchased I/A/W HOSE ASSEMBLY, CATAPULT EXCEPTION NOTE: USE NAVSEA DOC S9074-AR-GIB-010/278 WELDING/CASTING FABRICATION and INSPECTION PROCEDURES THAT REPLACES CANCELED SPECIFICATION MIL-STD-278 SAMPLING: IF THE APPLICABLE (OEM OR MILITARY) DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES AN ACCEPTABLE QUALITY LEVEL (AQL), IT MAY BE USED TO ESTABLISH THE AUTHORIZED SAMPLE SIZE. HOWEVER THE SAMPLING ACCEPTANCE NUMBER SHALL BE REDUCED TO ZERO (0). EVEN THOUGH THE ACCEPTANCE LEVEL IS ELIMINATED, THE SAMPLE SIZE REMAINS THE SAME. UNLESS OTHERWISE SPECIFIED IN THE OEM OR MILITARY DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISIONS (QAPs) CHARACTERISTICS CLASSIFIED AS CRITICAL, MAJOR AND MINOR SHALL HAVE AN ASSIGNED AQL OF 0.10, 1.0, AND 4.0 RESPECTIVELY. ASQ H1331 TABLE 1 OR MIL-STD-1916 SHALL TAKE PRECEDENCE OVER MIL-STD-105 AND ASQ Z1.4. THESE PLANS ACCEPT ON ZERO DEFECTS AND REJECT THE ENTIRE LOT ON ONE DEFECT. A ZERO BASED SAMPLING PLAN SHALL BE USED, UNLESS OTHERWISE SPECIFIED BY CONTRACT. MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS; AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA. PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR MERCURY COMPOUND. (IAW NAVSEA 5100-003D). THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL AGREEMENTS. TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, MILITARY CRITICAL TECHNICAL DATA AGREEMENT, FORM IS AVAILABLE AT THE WORLD WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO: DLA LOGISTICS INFORMATION SERVICE FEDERAL CENTER 74 WASHINGTON AVE., NORTH BATTLE CREEK, MI 49037-3084 TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT, DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 EXEMPTIONS OF GENERAL APPLICABILITY, AND/OR EAR PART 740 ARE APPLICABLE. NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL DATA ARE REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO RECEIVE A COPY OF THE EXPORT CONTROLLED TECHNICAL DATA. NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY PERMITTED BY DODD 5230.25. THIS MATERIAL MUST MEET NAVAIR AIRCRAFT LAUNCH & RECOVERY EQUIPMENT TRACEABILITY REQUIREMENTS. BARE ITEM MARKINGS SHALL BE IAW THE TECHNICAL DATA DRAWINGS PROVIDED. BARE ITEM MATERIAL SHALL BE MARKED WITH CONTRACT NUMBER, NAWC CAGE, AND PART NUMBER UNLESS OTHERWISE SPECIFICIED ON ASSOCIATED DRAWING. IF A CONFLICT EXISTS WITH MARKING REQUIREMENTS OF THIS 82N ALRE/SE ITEM, THE ASSOCIATED DRAWING REQUIREMENTS SHALL APPLY. 52.246-11 Higher Level Contract Quality Requirement (Manufacturers) FAR CLAUSE 52.246-11 APPLIES. A QUALITY MANAGEMENT PROGRAM MEETING THE REQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008 (EXAMPLE SAE AS 9100), THE FOLLOWING TAILORED VERSION OF ISO 9001:2008; OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008 (EXAMPLE SAE AS 9003) IS REQUIRED. MIL-I-45208 AND MIL-Q-9858 ARE OBSOLETE AND NO LONGER CONSIDERED SUITABLE WHEN HIGHER LEVEL QUALITY IS REQUIRED. IN THE TAILORED VERSION OF THE ISO 9001:2008, ANY REFERENCES WHICH CITE THE ENTIRE INTERNATIONAL STANDARD ARE INTERPRETED AS EXCLUSIONS TO THIS DOCUMENT. DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008 4.1 General requirements, [excluding reference to 1.2 and excluding NOTE 3 c)] 4.2.1 General, [excluding subparagraph a)] 4.2.2 Quality manual, [excluding subparagraph a)] 4.2.3 Control of documents 4.2.4 Control of records 5.1 Management commitment 5.3 Quality policy 6.2.2 Competence, training and awareness 6.4 Work environment 7.1 Planning of product realization, [excluding NOTE 2] 7.2.1 Determination of requirements related to the product 7.2.2 eview of requirements related to the product 7.2.3 Customer communication 7.3.7 Control of design and development changes 7.4.1 Purchasing process 7.4.3 Verification of purchased product 7.5.1 Control of production and service provision 7.5.3 Identification and traceability 7.5.4 Customer property 7.5.5 Preservation of product 7.6 Control of monitoring and measuring equipment 8.1 General, [excluding subparagraph b) and subparagraph c)] 8.2.2 Internal audit 8.2.4 Monitoring and measurement of product 8.3 Control of nonconforming product 8.5.2 Corrective action 8.5.3 Preventive action ENGINEERING CHANGE PROPOSALS (ECP) AND REQUESTS FOR WAIVERS AND DEVIATIONS, SHALL BE PROCESSED AND SUBMITTED AS SPECIFIED BY AND IN ACCORDANCE WITH MIL-STD-973. FULL AND OPEN COMPETITION APPLY IAW BASIC DRAWING NR 80020 521195 REVISION NR A DTD 09/13/2006 PART PIECE NUMBER: 521195-1 IAW REFERENCE DRAWING NR 80020 521083 REVISION NR A DTD 09/13/2006 PART PIECE NUMBER: 521083-1 IAW REFERENCE DRAWING NR 80020 B314120 REVISION NR E DTD 09/13/2006 PART PIECE NUMBER: The anticipated destinations is Tracy CA 95376-5000. The anticipated packaging requirements are as follows: PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999 QUP:001 PRES MTHD:ZZ CLNG/DRY:X PRESV MAT:XX WRAP MAT:XX CUSH/DUNN MAT:XX CUSH/DUNN THKNESS:X UNIT CONT:XX OPI:A INTRMDTE CONT:XX INTRMDTE CONT QTY:XXX PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:00 -00 No special marking PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008 PRESERVATION AND PACKAGING SHALL BE IAW ASTM-D3951, COMMERCIAL PACKAGING. The solicitation is anticipated to require inspection of the supplies and packaging at origin. All interested parties are invited to express your interest in this procurement by completing the attached Market Survey and returning to the buyer, Jana M Engels-Stinson, at jana.engels-stinson@dla.mil on or before 1/22/16.
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DLA/J3/DSCC-BSM/SPE7M216R0004/listing.html)
- Record
- SN03990600-W 20160115/160113234903-b042b4b8821ef52e814f6e49ebb04ca3 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |