AWARD
17 -- Large Purchase
- Notice Date
- 9/16/2016
- Notice Type
- Award Notice
- NAICS
- 333999
— All Other Miscellaneous General Purpose Machinery Manufacturing
- Contracting Office
- Defense Logistics Agency, DLA Acquisition Locations, DLA Land and Maritime, P O Box 3990, Columbus, Ohio, 43218-3990, United States
- ZIP Code
- 43218-3990
- Solicitation Number
- SPE7M215R0076
- Archive Date
- 10/1/2016
- Point of Contact
- Kyle D. Barr, Phone: 6146921243
- E-Mail Address
-
kyle.barr@dla.mil
(kyle.barr@dla.mil)
- Small Business Set-Aside
- N/A
- Award Number
- SPE7M216C0056
- Award Date
- 9/16/2016
- Awardee
- Capy Machine Shop Inc.
- Award Amount
- $706,640.00
- Description
- TAPE CONNECTOR ASSY 82N Critical Safety Item (CSI) GOVERNMENT FIRST ARTICLE TESTING APPLIES PRE-AWARD AND POST-AWARD SURVEY APPLIES THE FOLLOWING DD FORM 1423 CDRL'S APPLY: CDRL 14-12025FAT CDRL 14-12025PTI THE FOLLOWING SUPPLEMENTAL QUALITY ASSURANCE PROVISIONS APPLY: SQAP009903783QA SQAP009903783FAT AIRCRAFT LAUNCH AND RECOVERY EQUIPMENT (ALRE). CRITICAL APPLICATION ITEM.. ALL REQUESTS FOR WAIVERS OR DEVIATIONS CLASSIFIED AS CRITICAL, MAJOR, OR MINOR MUST BE FORWARDED TO THE DSC CONTRACTING OFFICER FOR REVIEW AND APPROVAL.. ALL ITEMS OF SUPPLY SHALL BE MARKED IAW MIL-STD-129. IN ADDITION, EACH UNIT PACK WILL BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE), CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S CAGE CODE AND PART NUMBER. PCO MANDATORY INSPECTION. DURING PRODUCTION, MANDATORY INSPECTION IS REQUIRED TO BE ACCOMPLISHED AND DOCUMENTED BY THE CONTRACTOR AS FOLLOWS:. CRITICAL AND MAJOR CHARACTERISTICS AS IDENTIFIED IN CLASSIFICATION OF CHARACTERISTICS BLOCK ON DRAWING(S), TECHNICAL SPECIFICATIONS, SECOND TIER DOCUMENTS REFERENCED IN THE ACQUISITION ITEM DESCRIPTION AND SPECIFIED IN THE PROCUREMENT DOCUMENT, AND CHARACTERISTICS DEFINED AS: (A) MATERIAL CERTIFICATIONS (B) DESTRUCTIVE AND / OR NONDESTRUCTIVE TEST RESULTS (WHEN APPLICABLE) (C) ATTRIBUTES FOR PLATING HARDNESS. IMPORTANT MINOR CHARACTERISTICS SHALL BE DEFINED BY THE CONTRACTOR SUBJECT TO QAR CONCURRENCE, UNLESS OTHERWISE DEFINED ON APPLICABLE DRAWING(S), SPECIFICATIONS AND CHARRACTERISTICS DEFINED AS: (A) DIAMETRICAL AND LINEAR DIMENSIONS HAVING A TOLERANCE OF +/- 0.005 INCH OR LESS (B) GEOMETRIC FEATURE CONTROLS HAVING A TOTAL TOLERANCE OF 0.003 INCH OR LESS (C) SURFACE FINISHES HAVING A 16 VALUE OR LESS (D) CLASS THREE THREADS (E) ANGULAR TOLERANCES WITH A TOTAL RANGE LESS THAN 1 DEGREE. LEVEL OF INSPECTION: ANSI / ASQC Z1.4 FOR SINGLE SAMPLING USING A GENERAL INSPECTION LEVEL O II (A) CRITICAL AND MAJOR CHARACTERISTICS: 100% INSPECTION APPLIES (B) IMPORTANT MINOR CHARACTERISTICS: AQL OF 1.5. CERTIFICATION / DATA REPORTS: THE CONTRACTOR IS RESPONSIBLE FOR PREPARING A CERTIFICATE OF QUALITY COMPLIANCE (COQC) IN ACCORDANCE WITH THE DD FORM 1423 CONTRACT DATA REQUIREMENTS LIST (CDRL). THE COQC CONTENT WILL INCLUDE AS A MINIMUM THE DATA DESCRIBED IN DLAR CLAUSE 52.246-9000, IN ADDITION TO ALL PCO MANDATORY INSPECTION RESULTS. THIS COQC REQUIREMENT APPLIES TO EACH UNIT OF CONTRACT QUANTITY. CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. 52.246-11 Higher Level Contract Quality Requirement (Manufacturers) FAR CLAUSE 52.246-11 APPLIES. A QUALITY MANAGEMENT PROGRAM MEETING THE REQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008 (EXAMPLE SAE AS 9100), THE FOLLOWING TAILORED VERSION OF ISO 9001:2008; OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008 (EXAMPLE SAE AS 9003) IS REQUIRED. IN THE TAILORED VERSION OF THE ISO 9001:2008, ANY REFERENCES WHICH CITE THE ENTIRE INTERNATIONAL STANDARD ARE INTERPRETED AS EXCLUSIONS TO THIS DOCUMENT. DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008 4.1 General requirements, [excluding reference to 1.2 and excluding NOTE 3 c)] 4.2.1 General, [excluding subparagraph a)] 4.2.2 Quality manual, [excluding subparagraph a)] 4.2.3 Control of documents 4.2.4 Control of records 5.1 Management commitment 5.3 Quality policy 6.2.2 Competence, training and awareness 6.4 Work environment 7.1 Planning of product realization, [excluding NOTE 2] 7.2.1 Determination of requirements related to the product 7.2.2 Review of requirements related to the product 7.2.3 Customer communication 7.3.7 Control of design and development changes 7.4.1 Purchasing process 7.4.3 Verification of purchased product 7.5.1 Control of production and service provision 7.5.3 Identification and traceability 7.5.4 Customer property 7.5.5 Preservation of product 7.6 Control of monitoring and measuring equipment 8.1 General, [excluding subparagraph b) and subparagraph c)] 8.2.2 Internal audit 8.2.4 Monitoring and measurement of product 8.3 Control of nonconforming product 8.5.2 Corrective action 8.5.3 Preventive action REMINDER: THIS IS A CRITICAL ITEM AND ALL MAJOR AND MINOR WAIVER/DEVIATION REQUESTS MUST BE FORWARDED TO THE DSCC CONTRACTING OFFICER WHO WILL COORDINATE THE REVIEW AND APPROVAL THROUGH THE RESPONSIBLE ENGINEERING SERVICE ACTIVITY. NOTE: THIS IS A RESTRICTED SOURCE ITEM AND REQUIRES ENGINEERING SOURCE APPROVAL BY THE GOVERNMENT DESIGN CONTROL ACTIVITY. "CERTIFICATE OF QUALITY COMPLIANCE IS MANDATORY" THIS MATERIAL MUST MEET NAVAIR AIRCRAFT LAUNCH & RECOVERY EQUIPMENT TRACEABILITY REQUIREMENTS. BARE ITEM MARKINGS SHALL BE IAW THE TECHNICAL DATA DRAWINGS PROVIDED. BARE ITEM MATERIAL SHALL BE MARKED WITH CONTRACT NUMBER, NAWC CAGE, AND PART NUMBER UNLESS OTHERWISE SPECIFICIED ON ASSOCIATED DRAWING. IF A CONFLICT EXISTS WITH MARKING REQUIREMENTS OF THIS 82N ALRE/SE ITEM, THE ASSOCIATED DRAWING REQUIREMENTS SHALL APPLY. EACH UNIT PACKAGE WILL BE MARKED WITH THE NSN, CONTRACT NUMBER, LOT NUMBER, CONTRACTOR CAGE CODE, MANUFACTURER CAGE CODE, AND PART NUMBER. CAPY MACHINE SHOP INC. DBA 0BVP9 P/N 510445-1 MICRO STEEL INC. DBA 0T9A2 P/N 510445-1 WELLMAN DYNAMICS MACHINING AND 6JRD9 P/N 510445-1 IAW REFERENCE DRAWING NR 80020 MPR1212 REVISION NR R DTD 10/19/1990 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 MPR1221 REVISION NR R DTD 10/01/2001 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 416074 REVISION NR L DTD 02/24/2012 PART PIECE NUMBER: IAW REFERENCE QAP 16236 SQAP009903783QA REVISION NR DTD 03/12/2014 PART PIECE NUMBER: IAW REFERENCE QAP 16236 SQAP009903783 REVISION NR DTD 03/12/2014 PART PIECE NUMBER: IAW REFERENCE QAP 16236 CDRL-14-12025FAT REVISION NR DTD 01/27/2014 PART PIECE NUMBER: IAW REFERENCE QAP 16236 CDRL-14-12025PTI REVISION NR DTD 01/27/2014 PART PIECE NUMBER: IAW REFERENCE QAP 16236 CDRL-14-12025COQC REVISION NR DTD 01/27/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 16236 CN009903783 REVISION NR DTD 03/12/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 510445 REVISION NR G DTD 02/22/2012 PART PIECE NUMBER: 510445-1 IAW REFERENCE DRAWING NR 80020 510465 REVISION NR J DTD 09/16/2010 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 80020 510466 REVISION NR D DTD 06/28/2010 PART PIECE NUMBER:
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DLA/J3/DSCC/Awards/SPE7M216C0056.html)
- Record
- SN04275971-W 20160918/160916235503-e51bca72be3c3cd86ebf04882a4bc0d8 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |