SOLICITATION NOTICE
61 -- INI Trinity 2000 Hybrid Power Kit
- Notice Date
- 9/20/2016
- Notice Type
- Combined Synopsis/Solicitation
- NAICS
- 221118
— Other Electric Power Generation
- Contracting Office
- Department of the Army, Army Contracting Command, ACC - WRN (W56HZV)(DTA), 6501 EAST 11 MILE ROAD, Warren, Michigan, 48397-5000, United States
- ZIP Code
- 48397-5000
- Solicitation Number
- W56HZV-16-T-0237
- Archive Date
- 10/7/2016
- Point of Contact
- Shonna Tyson, Phone: 5862823070, Jared Charmbers, Phone: (586) 282-7491
- E-Mail Address
-
shonna.l.tyson.civ@mail.mil, jared.j.chambers2.civ@mail.mil
(shonna.l.tyson.civ@mail.mil, jared.j.chambers2.civ@mail.mil)
- Small Business Set-Aside
- N/A
- Description
- I. INTRODUCTION A. This is a Combined Synopsis-Solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6 as supplemented with additional information in this notice. This announcement constitutes the only solicitation; quotations are being requested and a written solicitation will not be issued. B. The Combined Synopsis and Request for Quotation (RFQ) number is: W56HZV-16-T-0237 C. This solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2005-83, effective 3 September 2015. D. Small Business Set-Aside: 100% Small Business Set-Aside E. Posting Date: 20 September 2016 F. Response Date: 22 September 2016 G. Contracting Office: Army Contracting Command - Warren (ACC-WRN), 6501 East 11 Mile Road, Warren, MI 48397-5000. H. The NAICS code applicable to this acquisition is 221118, Cutting Tool and Machine Tool Accessory Manufacturing (250 Employees). Offeror must be certified under this NAICS code prior to receiving an award. I. This Combined Synopsis-Solicitation contains clauses and provisions requiring a fill-in or representation. Offeror shall submit a copy of this Combined Synopsis-Solicitation with their quotation and respond to these clauses and provisions accordingly. A failure to complete these fill-ins may cause your quotation to be determined ineligible for award. J. Basis for award - The proposed contract action is for supplies or services for which the Government intends to solicit and negotiate with only one source under the authority of FAR 13.106-1(b)(1)(i). Interested persons may identify their interest and capability to respond to the requirement or submit proposals before the closing date of this solicitation. A determination by the Government not to compete this proposed contract based upon responses to this notice is solely within the discretion of the Government. Information received will normally be considered solely for the purpose of determining whether to conduct a competitive procurement. The Government intends to negotiate and award a contract to INI Trinity Power Systems. II. GENERAL A. The United States Army Tank and Automotive Research, Development and Engineering Center (TARDEC) in Warren, Michigan has requirements for the following: CLIN DESCRIPTION QTY UOM PRICE 0001 INI Trinity 2000 Hybrid Power Kit 1 EA Offeror shall include all shipping charges and deliver supplies F.O.B. DESTINATION to the following address: US Army TARDEC Michael Anderson, Ph.D. Chemical Engineer 6501 E. Eleven Mile Rd MS #110 Warren, MI 48397-5000 Offeror shall deliver requirement by the following date: 31 December 2016 B. This acquisition is unrated under the Defense Priorities and Allocations System (DPAS). C. Quotations must be received by ACC-WRN no later than 5:00 PM / 1700 HRS local Warren, MI time, 22 September 2016. Email quotation to Shonna Tyson, Contract Specialist at Shonna.L.Tyson.civ@mail.mil. D. Offeror must be registered in System for Award Management (SAM) prior to receiving an award. Refer to website https://www.sam.gov/portal/public/SAM/. III. SOLICITATION PROVISIONS AND CONTRACT CLAUSES The following provisions and clauses apply to this Combined Synopsis/Solicitation: CLAUSES INCORPORATED BY REFERENCE FAR 52.204-7 System for Award Management FAR 52.211-6 Brand Name or Equal FAR 52.212-1 Instructions to Offerors-Commercial Items (Provision) FAR 52.212-4 Contract Terms and Conditions-Commercial Items FAR 52.233-1 Disputes FAR 52.246-2 Inspection of Supplies FAR 52.246-16 Responsibility for Supplies FAR 52.247-34 F.O.B. Destination DFARS 252.203-7000 Requirements Relating to Compensation of Former DoD Officials DFARS 252.204-7006 Billing Instructions DFARS 252.204-7012 Safeguarding Unclassified Technical Information DFARS 252.225-7001 Buy American and Balance of Payments Program DFARS 252.225-7002 Qualifying Country Sources as Subcontractors DFARS 252.232-7003 Electronic Submission of Payment Requests DFARS 252.232-7010 Levies on Contract Payments DFARS 252.243-7001 Pricing of Contract Mods DFARS 252.246-7000 Material Inspection and Receiving Report CLAUSES INCORPORATED BY FULL TEXT 52.201-4000 (Local) - Army Contracting Command - Warren Ombudsperson (APR 2011) Information regarding the TACOM-Warren Ombudsperson is located at the website http://contracting.tacom.army.mil/acqinfo/ombudsperson.htm. (End of Clause) 52.212-3 - Offeror Representations and Certifications - Commercial Items Alternate I (OCT 2014) [The offeror shall check the category in which its ownership falls]: ___ Black American. ___ Hispanic American. ___ Native American (American Indians, Eskimos, Aleuts, or Native Hawaiians). ___ Asian-Pacific American (persons with origins from Burma, Thailand, Malaysia, Indonesia, Singapore, Brunei, Japan, China, Taiwan, Laos, Cambodia (Kampuchea), Vietnam, Korea, The Philippines, Republic of Palau, Republic of the Marshall Islands, Federated States of Micronesia, the Commonwealth of the Northern Mariana Islands, Guam, Samoa, Macao, Hong Kong, Fiji, Tonga, Kiribati, Tuvalu, or Nauru). ___ Subcontinent Asian (Asian-Indian) American (persons with origins from India, Pakistan, Bangladesh, Sri Lanka, Bhutan, the Maldives Islands, or Nepal). ___ Individual/concern, other than one of the preceding. (End of Provision) 52.212-5 - Contract Terms and Conditions Required to Implement Statutes or Executive Orders--Commercial Items (DEVIATION 2013-O0019) (JUL 2014) (a) Comptroller General Examination of Record. The Contractor shall comply with the provisions of this paragraph (a) if this contract was awarded using other than sealed bid, is in excess of the simplified acquisition threshold, and does not contain the clause at 52.215-2, Audit and Records -- Negotiation. (1) The Comptroller General of the United States, or an authorized representative of the Comptroller General, shall have access to and right to examine any of the Contractor's directly pertinent records involving transactions related to this contract. (2) The Contractor shall make available at its offices at all reasonable times the records, materials, and other evidence for examination, audit, or reproduction, until 3 years after final payment under this contract or for any shorter period specified in FAR Subpart 4.7, Contractor Records Retention, of the other clauses of this contract. If this contract is completely or partially terminated, the records relating to the work terminated shall be made available for 3 years after any resulting final termination settlement. Records relating to appeals under the disputes clause or to litigation or the settlement of claims arising under or relating to this contract shall be made available until such appeals, litigation, or claims are finally resolved. (3) As used in this clause, records include books, documents, accounting procedures and practices, and other data, regardless of type and regardless of form. This does not require the Contractor to create or maintain any record that the Contractor does not maintain in the ordinary course of business or pursuant to a provision of law. (b) (1) Notwithstanding the requirements of any other clause in this contract, the Contractor is not required to flow down any FAR clause, other than those in this paragraph (b)(1) in a subcontract for commercial items. Unless otherwise indicated below, the extent of the flow down shall be as required by the clause- (i) 52.203-13, Contractor Code of Business Ethics and Conduct (Apr 2010) (41 U.S.C. 3509). (ii) 52.219-8, Utilization of Small Business Concerns (Oct 2014) (15 U.S.C. 637(d)(2) and (3)), in all subcontracts that offer further subcontracting opportunities. If the subcontract (except subcontracts to small business concerns) exceeds $650,000 ($1.5 million for construction of any public facility), the subcontractor must include 52.219-8 in lower tier subcontracts that offer subcontracting opportunities. (iii) 52.222-17, Nondisplacement of Qualified Workers (May 2014) (E.O. 13495). Flow down required in accordance with paragraph (1) of FAR clause 52.222-17. (iv) 52.222-21, Prohibition of Segregated Facilities (Apr 2015). (v) 52.222-26, Equal Opportunity (Mar 2007) (E.O. 11246). (vi) 52.222-35, Equal Opportunity for Veterans (Jul 2014) (38 U.S.C. 4212). (vii) 52.222-36, Equal Opportunity for Workers with Disabilities (Jul 2014) (29 U.S.C. 793). (viii) 52.222-37, Employment Reports on Veterans (Jul 2014) (38 U.S.C. 4212). (ix) 52.222-40, Notification of Employee Rights Under the National Labor Relations Act (Dec 2010) (E.O. 13496). Flow down required in accordance with paragraph (f) of FAR clause 52.222-40. (x) 52.222-41, Service Contract Labor Standards (May 2014), (41 U.S.C. chapter 67). (xi) ____ (A) 52.222-50, Combating Trafficking in Persons (Mar 2015) (22 U.S.C. chapter 78 and E.O. 13627). ___ (B) Alternate I (Mar 2015) of 52.222-50 (22 U.S.C. chapter 78 E.O. 13627). (xii) 52.222-51, Exemption from Application of the Service Contract Labor Standards to Contracts for Maintenance, Calibration, or Repair of Certain Equipment--Requirements (May 2014) (41 U.S.C. chapter 67.) (xiii) 52.222-53, Exemption from Application of the Service Contract Labor Standards to Contracts for Certain Services--Requirements (May 2014) (41 U.S.C. chapter 67) (xiv) 52.222-54, Employment Eligibility Verification (Aug 2013). (xv) 52.222-55, Minimum Wages Under Executive Order 13658 (Dec 2014) (E.O. 13658). (xvi) 52.225-26, Contractors Performing Private Security Functions Outside the United States (Jul 2013) (Section 862, as amended, of the National Defense Authorization Act for Fiscal Year 2008; 10 U.S.C. 2302 Note). (xvii) 52.226-6, Promoting Excess Food Donation to Nonprofit Organizations. (May 2014) (42 U.S.C. 1792). Flow down required in accordance with paragraph (e) of FAR clause 52.226-6. (xviii) 52.247-64, Preference for Privately-Owned U.S. Flag Commercial Vessels (Feb 2006) (46 U.S.C. Appx 1241(b) and 10 U.S.C. 2631). Flow down required in accordance with paragraph (d) of FAR clause 52.247-64. (2) While not required, the contractor may include in its subcontracts for commercial items a minimal number of additional clauses necessary to satisfy its contractual obligations. (End of Clause) 52.225-18 - Place of Manufacture (MAR 2015) (a) Definitions. As used in this clause- "Manufactured end product" means any end product in Federal Supply Classes (FSC) 1000-9999, except- (1) FSC 5510, Lumber and Related Basic Wood Materials; (2) Federal Supply Group (FSG) 87, Agricultural Supplies; (3) FSG 88, Live Animals; (4) FSG 89, Food and Related Consumables; (5) FSC 9410, Crude Grades of Plant Materials; (6) FSC 9430, Miscellaneous Crude Animal Products, Inedible; (7) FSC 9440, Miscellaneous Crude Agricultural and Forestry Products; (8) FSC 9610, Ores; (9) FSC 9620, Minerals, Natural and Synthetic; and (10) FSC 9630, Additive Metal Materials. "Place of manufacture" means the place where an end product is assembled out of components, or otherwise made or processed from raw materials into the finished product that is to be provided to the Government. If a product is disassembled and reassembled, the place of reassembly is not the place of manufacture. (b) For statistical purposes only, the offeror shall indicate whether the place of manufacture of the end products it expects to provide in response to this solicitation is predominantly- (1) [ ] In the United States (Check this box if the total anticipated price of offered end products manufactured in the United States exceeds the total anticipated price of offered end products manufactured outside the United States); or (2) [ ] Outside the United States. (End of Provision) 52.232-4007 (Local) - Wide Area Workflow (WAWF), Codes and Designated Acceptors (AUG 2012) The contractor shall use WAWF to electronically process invoices for payment and receiving reports. The contractor shall register to use WAWF and take the Web-based training at https://wawf.eb.mil. Direct any questions relating to the system and vendor training to the Ogden Help Desk at 866-618-5988. To properly route an invoice and receiving report through WAWF, the contractor shall indicate the following when prompted: 1. Select the appropriate type of invoice as indicated below. It is imperative that contractors select the proper type of invoice. Improper selection of an invoice type will result in the delay of a payment or the rejection of an invoice submittal. X Invoice and Receiving Report Combo (Supplies) Use for contracts that are entirely for supply requirements or for contracts that are predominantly for supply requirements but also includes minimal service line items. Invoice 2-in-1 (Services) Use for contracts that are entirely for service requirements. 2. Use the following DoDAAC (Department of Defense Activity Address Code) codes when prompted:  Your firm's CAGE Code (found in Block 17a of SF 1449):  Issue and Admin DoDAAC Code (found in Block 9 of SF 1449): W56HZV  Ship-To DoDAAC Code (if deliverables are involved - found in Block 15 of SF 1449): TBA  Accept-By DoDAAC Code: TBA  Payment DoDAAC Code (found in Block 18a of SF 1449): HQ0490 3. Include the Purchase Request Number as specified in each Contract Line Item Number (CLIN). This number can be found at the bottom of the extended description of each CLIN. NOTE: The purchase request number may be different for each CLIN. 4. Indicate the proper Unit of Measure as specified in each CLIN. Failure to indicate the proper Unit of Measure will lead to vendor pay issues. 5. Indicate the following Acceptor, Alternate Acceptor, and Contract Specialist when the WAWF system prompts for "additional e-mail submission" after clicking "Signature".  Primary Acceptor Name: TBA  Primary Acceptor E-mail: TBA  Alternate Acceptor Name: TBA  Alternate Acceptor E-mail: TBA  Contract Specialist Name: Shonna Tyson  Contract Specialist e-mail: Shonna.L.Tyson.civ@mail.mil To track the status of an invoice, in WAWF click on the link, "Pay Status" (myInvoice-External link) found under the tab named "Lookup" or by going to https://myinvoice.csd.disa.mil/index.html. If the payment office indicated in the contract is Columbus, direct any payment related questions to the Defense Finance Accounting Services (DFAS) Columbus at 800-756-4571. If the payment office is other than Columbus, contact the contract administrator for the customer service phone/fax numbers. (End of Clause) 52.246-4009 (Local) - Inspection and Acceptance Points: Destination (FEB 1995) Inspection and acceptance of supplies offered under this purchase order shall take place as specified here. Inspection: DESTINATION. Acceptance: DESTINATION (End of Clause) 52.252-1 - Solicitation Provisions Incorporated by Reference (FEB 1998) This solicitation incorporates one or more solicitation provisions by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. The offeror is cautioned that the listed provisions may include blocks that must be completed by the offeror and submitted with its quotation or offer. In lieu of submitting the full text of those provisions, the offeror may identify the provision by paragraph identifier and provide the appropriate information with its quotation or offer. Also, the full text of a solicitation provision may be accessed electronically at this address: http://farsite.hill.af.mil/ (End of Provision) 52.252-2 - Clauses Incorporated by Reference (FEB 1998) This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this address: http://farsite.hill.af.mil/ (End of Clause) 252.209-7999 - Representation by Corporations Regarding an Unpaid Delinquent Tax Liability or a Felony Conviction Under Any Federal Law (DEVIATION 2012-O0004) (JAN 2012) (a) In accordance with sections 8124 and 8125 of Division A of the Consolidated Appropriations Act, 2012, (Pub. L. 112-74) none of the funds made available by that Act may be used to enter into a contract with any corporation that- (1) Has any unpaid Federal tax liability that has been assessed, for which all judicial and administrative remedies have been exhausted or have lapsed, and that is not being paid in a timely manner pursuant to an agreement with the authority responsible for collecting the tax liability, where the awarding agency is aware of the unpaid tax liability, unless the agency has considered suspension or debarment of the corporation and made a determination that this further action is not necessary to protect the interests of the Government. (2) Was convicted of a felony criminal violation under any Federal law within the preceding 24 months, where the awarding agency is aware of the conviction, unless the agency has considered suspension or debarment of the corporation and made a determination that this action is not necessary to protect the interests of the Government. (b) The Offeror represents that- (1) It is [ ___ ] is not [ ___ ] a corporation that has any unpaid Federal tax liability that has been assessed, for which all judicial and administrative remedies have been exhausted or have lapsed, and that is not being paid in a timely manner pursuant to an agreement with the authority responsible for collecting the tax liability, (2) It is [ ___ ] is not [ ___ ] a corporation that was convicted of a felony criminal violation under a Federal law within the preceding 24 months. (End of Provision) 252.211-7003 - Item Unique Identification and Valuation (DEC 2013) (a) Definitions. As used in this clause- "Automatic identification device" means a device, such as a reader or interrogator, used to retrieve data encoded on machine-readable media. "Concatenated unique item identifier" means- (1) For items that are serialized within the enterprise identifier, the linking together of the unique identifier data elements in order of the issuing agency code, enterprise identifier, and unique serial number within the enterprise identifier; or (2) For items that are serialized within the original part, lot, or batch number, the linking together of the unique identifier data elements in order of the issuing agency code; enterprise identifier; original part, lot, or batch number; and serial number within the original part, lot, or batch number. "Data matrix" means a two-dimensional matrix symbology, which is made up of square or, in some cases, round modules arranged within a perimeter finder pattern and uses the Error Checking and Correction 200 (ECC200) specification found within International Standards Organization (ISO)/International Electrotechnical Commission (IEC) 16022. "Data qualifier" means a specified character (or string of characters) that immediately precedes a data field that defines the general category or intended use of the data that follows. "DoD recognized unique identification equivalent" means a unique identification method that is in commercial use and has been recognized by DoD. All DoD recognized unique identification equivalents are listed at http://www.acq.osd.mil/dpap/pdi/uid/iuid_equivalents.html. "DoD item unique identification" means a system of marking items delivered to DoD with unique item identifiers that have machine-readable data elements to distinguish an item from all other like and unlike items. For items that are serialized within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier and a unique serial number. For items that are serialized within the part, lot, or batch number within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier; the original part, lot, or batch number; and the serial number. "Enterprise" means the entity (e.g., a manufacturer or vendor) responsible for assigning unique item identifiers to items. "Enterprise identifier" means a code that is uniquely assigned to an enterprise by an issuing agency. "Government's unit acquisition cost" means- (1) For fixed-price type line, subline, or exhibit line items, the unit price identified in the contract at the time of delivery; (2) For cost-type or undefinitized line, subline, or exhibit line items, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery; and (3) For items produced under a time-and-materials contract, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery. "Issuing agency" means an organization responsible for assigning a globally unique identifier to an enterprise (i.e., Dun & Bradstreet's Data Universal Numbering System (DUNS) Number, GS1 Company Prefix, Allied Committee 135 NATO Commercial and Government Entity (NCAGE)/ Commercial and Government Entity (CAGE) Code, or the Coded Representation of the North American Telecommunications Industry Manufacturers, Suppliers, and Related Service Companies (ATIS-0322000) Number), European Health Industry Business Communication Council (EHIBCC) and Health Industry Business Communication Council (HIBCC)), as indicated in the Register of Issuing Agency Codes for ISO/IEC 15459, located at http://www.nen.nl/Normontwikkeling/Certificatieschemas-en-keurmerken/Schemabeheer/ISOIEC-15459.htm under "Register." "Issuing agency code" means a code that designates the registration (or controlling) authority for the enterprise identifier. "Item" means a single hardware article or a single unit formed by a grouping of subassemblies, components, or constituent parts. "Lot or batch number" means an identifying number assigned by the enterprise to a designated group of items, usually referred to as either a lot or a batch, all of which were manufactured under identical conditions. "Machine-readable" means an automatic identification technology media, such as bar codes, contact memory buttons, radio frequency identification, or optical memory cards. "Original part number" means a combination of numbers or letters assigned by the enterprise at item creation to a class of items with the same form, fit, function, and interface. "Parent item" means the item assembly, intermediate component, or subassembly that has an embedded item with a unique item identifier or DoD recognized unique identification equivalent. "Serial number within the enterprise identifier" means a combination of numbers, letters, or symbols assigned by the enterprise to an item that provides for the differentiation of that item from any other like and unlike item and is never used again within the enterprise. "Serial number within the part, lot, or batch number" means a combination of numbers or letters assigned by the enterprise to an item that provides for the differentiation of that item from any other like item within a part, lot, or batch number assignment. "Serialization within the enterprise identifier" means each item produced is assigned a serial number that is unique among all the tangible items produced by the enterprise and is never used again. The enterprise is responsible for ensuring unique serialization within the enterprise identifier. "Serialization within the part, lot, or batch number" means each item of a particular part, lot, or batch number is assigned a unique serial number within that part, lot, or batch number assignment. The enterprise is responsible for ensuring unique serialization within the part, lot, or batch number within the enterprise identifier. "Type designation" means a combination of letters and numerals assigned by the Government to a major end item, assembly or subassembly, as appropriate, to provide a convenient means of differentiating between items having the same basic name and to indicate modifications and changes thereto. "Unique item identifier" means a set of data elements marked on items that is globally unique and unambiguous. The term includes a concatenated unique item identifier or a DoD recognized unique identification equivalent. "Unique item identifier type" means a designator to indicate which method of uniquely identifying a part has been used. The current list of accepted unique item identifier types is maintained at http://www.acq.osd.mil/dpap/pdi/uid/uii_types.html. (b) The Contractor shall deliver all items under a contract line, subline, or exhibit line item. (c) Unique item identifier. (1) The Contractor shall provide a unique item identifier for the following: (i) Delivered items for which the Government's unit acquisition cost is $5,000 or more, except for the following line items: Contract Line, Subline, or Exhibit Line Item Number Item Description ________See Schedule________________________________________________ ___________________________________________________________________ ___________________________________________________________________ (ii) Items for which the Government's unit acquisition cost is less than $5,000 that are identified in the Schedule or the following table: Contract Line, Subline, or Exhibit Line Item Number Item Description _________See Schedule_______________________________________________ ___________________________________________________________________ ___________________________________________________________________ (iii) Subassemblies, components, and parts embedded within delivered items, items with warranty requirements, DoD serially managed reparables and DoD serially managed nonreparables as specified in Attachment Number ____. (iv) Any item of special tooling or special test equipment as defined in FAR 2.101 that have been designated for preservation and storage for a Major Defense Acquisition Program as specified in Attachment Number ____. (v) Any item not included in (i), (ii), (iii), or (iv) for which the contractor creates and marks a unique item identifier for traceability. (2) The unique item identifier assignment and its component data element combination shall not be duplicated on any other item marked or registered in the DoD Item Unique Identification Registry by the contractor. (3) The unique item identifier component data elements shall be marked on an item using two dimensional data matrix symbology that complies with ISO/IEC International Standard 16022, Information technology - International symbology specification - Data matrix; ECC200 data matrix specification. (4) Data syntax and semantics of unique item identifiers. The Contractor shall ensure that- (i) The data elements (except issuing agency code) of the unique item identifier are encoded within the data matrix symbol that is marked on the item using one of the following three types of data qualifiers, as determined by the Contractor: (A) Application Identifiers (AIs) (Format Indicator 05 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology - EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard. (B) Data Identifiers (DIs) (Format Indicator 06 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology - EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard. (C) Text Element Identifiers (TEIs) (Format Indicator 12 of ISO/IEC International Standard 15434), in accordance with the Air Transport Association Common Support Data Dictionary; and (ii) The encoded data elements of the unique item identifier conform to the transfer structure, syntax, and coding of messages and data formats specified for Format Indicators 05, 06, and 12 in ISO/IEC International Standard 15434, Information Technology - Transfer Syntax for High Capacity Automatic Data Capture Media. (5) Unique item identifier. (i) The Contractor shall- (A) Determine whether to- (1) Serialize within the enterprise identifier; (2) Serialize within the part, lot, or batch number; or (3) Use a DoD recognized unique identification equivalent (e.g. Vehicle Identification Number); and (B) Place the data elements of the unique item identifier (enterprise identifier; serial number; DoD recognized unique identification equivalent; and for serialization within the part, lot, or batch number only: original part, lot, or batch number) on items requiring marking by paragraph (c)(1) of this clause, based on the criteria provided in MIL-STD-130, Identification Marking of U.S. Military Property, latest version; (C) Label shipments, storage containers and packages that contain uniquely identified items in accordance with the requirements of MIL-STD-129, Military Marking for Shipment and Storage, latest version; and (D) Verify that the marks on items and labels on shipments, storage containers, and packages are machine readable and conform to the applicable standards. The contractor shall use an automatic identification technology device for this verification that has been programmed to the requirements of Appendix A, MIL-STD-130, latest version. (ii) The issuing agency code- (A) Shall not be placed on the item; and (B) Shall be derived from the data qualifier for the enterprise identifier. (d) For each item that requires item unique identification under paragraph (c)(1)(i), (ii), or (iv) of this clause or when item unique identification is provided under paragraph (c)(1)(v), in addition to the information provided as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the Contractor shall report at the time of delivery, as part of the Material Inspection and Receiving Report, thefollowing information: (1) Unique item identifier. (2) Unique item identifier type. (3) Issuing agency code (if concatenated unique item identifier is used). (4) Enterprise identifier (if concatenated unique item identifier is used). (5) Original part number (if there is serialization within the original part number). (6) Lot or batch number (if there is serialization within the lot or batch number). (7) Current part number (optional and only if not the same as the original part number). (8) Current part number effective date (optional and only if current part number is used). (9) Serial number (if concatenated unique item identifier is used). (10) Government's unit acquisition cost. (11) Unit of measure. (12) Type designation of the item as specified in the contract schedule, if any. (13) Whether the item is an item of Special Tooling or Special Test Equipment. (14) Whether the item is covered by a warranty. (e) For embedded subassemblies, components, and parts that require DoD item unique identification under paragraph (c)(1)(iii) of this clause or when item unique identification is provided under paragraph (c)(1)(v), the Contractor shall report as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the following information: (1) Unique item identifier of the parent item under paragraph (c)(1) of this clause that contains the embedded subassembly, component, or part. (2) Unique item identifier of the embedded subassembly, component, or part. (3) Unique item identifier type.** (4) Issuing agency code (if concatenated unique item identifier is used).** (5) Enterprise identifier (if concatenated unique item identifier is used).** (6) Original part number (if there is serialization within the original part number).** (7) Lot or batch number (if there is serialization within the lot or batch number).** (8) Current part number (optional and only if not the same as the original part number).** (9) Current part number effective date (optional and only if current part number is used).** (10) Serial number (if concatenated unique item identifier is used).** (11) Description. ** Once per item. (f) The Contractor shall submit the information required by paragraphs (d) and (e) of this clause as follows: (1) End items shall be reported using the receiving report capability in Wide Area WorkFlow (WAWF) in accordance with the clause at 252.232-7003. If WAWF is not required by this contract, and the contractor is not using WAWF, follow the procedures at http://dodprocurementtoolbox.com/site/uidregistry/. (2) Embedded items shall be reported by one of the following methods- (i) Use of the embedded items capability in WAWF; (ii) Direct data submission to the IUID Registry following the procedures and formats at http://dodprocurementtoolbox.com/site/uidregistry/; or (iii) Via WAWF as a deliverable attachment for exhibit line item number (fill in) ___, Unique Item Identifier Report for Embedded Items, Contract Data Requirements List, DD Form 1423. (g) Subcontracts. If the Contractor acquires by subcontract, any item(s) for which item unique identification is required in accordance with paragraph (c)(1) of this clause, the Contractor shall include this clause, including this paragraph (g), in the applicable subcontract(s), including subcontracts for commercial items. (End of Clause)
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/notices/b45e4c2e4cd17319fefac286009d0517)
- Place of Performance
- Address: US Army TARDEC, (Detroit Arsenal), 6501 E. Eleven Mile Rd MS #110, Warren, Michigan, 48397, United States
- Zip Code: 48397
- Zip Code: 48397
- Record
- SN04279682-W 20160922/160920235121-b45e4c2e4cd17319fefac286009d0517 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |