FBODaily.com | FedBizOpps: PRESOL | 41 | Chiller Controls Hanscom AFB

FBO DAILY - FEDBIZOPPS ISSUE OF SEPTEMBER 22, 2016 FBO #5417
SOLICITATION NOTICE

41 -- Chiller Controls Hanscom AFB

Notice Date: 9/20/2016
Notice Type: Cancellation
NAICS: 238220 — Plumbing, Heating, and Air-Conditioning Contractors
Contracting Office: Department of the Air Force, Air Force Materiel Command, AFLCMC/PK - WPAFB (includes PZ, WL, WW, WI, WN, WK, LP, WF, WK), 2275 D Street, Wright-Patterson AFB, Ohio, 45433-7218, United States
ZIP Code: 45433-7218
Solicitation Number: FA2835-16-P-0034
Archive Date: 9/28/2016
Point of Contact: Sharley A. Robertson, Phone: 781250151, William Engelhart, Phone: 781-225-0154
E-Mail Address: sharley.robertson@us.af.mil, william.engelhart.1@us.af.mil
(sharley.robertson@us.af.mil, william.engelhart.1@us.af.mil)
Small Business Set-Aside: N/A
Description: Combined Synopsis/Solicitation for Chiller Controls Hanscom AFB Contract Specialist: Sharley Robertson PCO: Lt William Engelhart 1. This is a combined Synopsis/Solicitation for commercial items prepared in accordance with the format in Federal Acquisition Regulation (FAR) Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued. ***NOTE*** All instructions, templates and formats contained herein shall explicitly be adhered to; otherwise, a quote is determined to be incomplete and shall not be considered for award. 2. Solicitation Number: F2B3AQ6182A019 3. This Synopsis/Solicitation is issued as a Request for Quote (RFQ) 4. Provisions and clauses in effect through Federal Acquisition Circular FAC 2005-89 5. A notice regarding any set-aside: Full and Open Competition 6. NAICS Code: 238220 7. Small Business Size Standard: $15.0M 8. Statement regarding the Small Business Competitiveness Demonstration Program, if applicable: N/A 9. Contract Line Item Number(s) (CLINs) and items, quantities and units of measure, (including option(s), if applicable): CONTRACT LINE ITEM NO. (CLIN) SUPPLIES/SERVICE QTY UNIT 0001 NON-PERSONAL SERVICES: FY 16 Chiller Controls Monthly Service to Chiller Controls Hanscom AFB 12 Monthly 1001 OPTION YEAR 1: FY17 Chiller Controls Monthly Service Contract Hanscom AFB 12 Monthly 2001 OPTION YEAR 2: FY18 Chiller Controls Monthly Service Contract Hanscom AFB 12 Monthly 3001 OPTION YEAR 3: FY19 Chiller Controls Monthly Service Contract Hanscom AFB 12 Monthly 4001 OPTION YEAR 4: FY20 Chiller Controls Monthly Service Contract Hanscom AFB 12 Monthly 10. Description of requirements for the items to be acquired: The contractor shall provide all labor, tools, equipment, hoses, gauges, test equipment, hearing protection, eye protection including prescription safety glasses, materials, supplies and parts, transportation and other incidentals necessary to travel to Hanscom AFB, MA, to perform Chiller Controls service on Hanscom Air Force Base (AFB). The contractor shall be responsible for insuring all services and parts provided under this contract are in accordance with the terms and conditions outlined herein and conform to the manufacturer's equipment specifications and this Performance Work Statement (PWS). The contractor must provide a technician who is currently certified by JCI on Facility Explorer Pro BAS and have a minimum 3 years concurrent. 11. Date of delivery / Period of Performance: 18 September 2016 - 17 September 2021 12. Place(s) of Delivery and Acceptance: Hanscom Air Force Base, MA 13. FOB Point: DESTINATION 14. Attachments: a) Performance Work Statement b) Bid Schedule c) Service Contract Act Wage Determinations d) Attachment Protected-Chiller_As-Builts 1 e) Attachment Protected-Chiller_As-Builts 2 15. The name and telephone number of the individual to contact for information regarding the solicitation: Sharley Robertson at sharley.robertson@us.af.mil, (781) 225-0151 and Lt William Engelhart at william.engelhart.1@us.af.mil, (781) 225-0154. 16. Additional Information: Be advised that all interested parties must be registered in the System for Award Management (SAM) Database in order to receive an award. If you are not registered you may make a request through the SAM website at http://www.sam.gov. Be advised that all interested parties must be registered as a small business in the Small Business Administration (SBA) Dynamic Business Search Database under the proper NAICS Code in order to receive an award. If you are not registered, you may self-certify through the SBA website at http://dsbs.sba.gov/dsbs/search/dsp_dsbs.cfm. IAW DFARS 252.232-7003(b)(1) all invoices shall be submitted via Wide Area Work Flow (WAWF) located at https://wawf.eb.mil/. (Procedures and POC's specific to this contract will be added to the contract). 17. The provision at FAR 52.212-1 Instructions to Offerors and 52.212-2 Evaluation - Commercial Items apply to this acquisition. Addendum to FAR 52.212-1, Instructions to Offerors The following is to be added to FAR 52.212-1 paragraph (b): Please provide your price quote on the attached bid schedule. The quote in its entirety shall not exceed fifteen (15) pages, double sided. *NOTE*: Responsive and complete quotes will be evaluated on price and past per-formance. Award will be made on the basis of price and other factors IAW FAR 13.106-2. NOTE: The aforementioned documentation are required for a quote to be considered complete for evaluation. Offers are due before 3 PM EST on Monday, September 19, 2016. Offers shall be emailed to sharley.robertson@us.af.mil and william.engelhart.1@us.af.mil Do not post offers to FedBizOpps. Please request read receipt on all submitted quotes. All questions are due before 12:00 Noon EST on Wednesday, Sept 14, 2016; answers will be posted to FedBizOpps NLT COB Thursday, Sept 15, 2016. There will be a site visit for this acquisition at 9:00 am EST on Monday Sep 19, 2016. Potential contractors wishing to attend this site visit will need to express their interest and the names of all individuals from the company who will be in attendance to Sharley Robertson via e-mail at sharley.robertson@us.af.mil by Friday Sept 9, 2016 EST, NOON. Vendors shall include a completed copy of the provision at FAR 52.212-3 Alt 1, Offeror Representations and Certifications -- Commercial Items. A vendor shall complete only paragraph (b) of this provision if the vendor has completed the annual representations and certificates electronically at http://www.sam.gov. If any vendor has not completed the annual representations and certifications electronically at the SAM website, the vendor shall complete only paragraphs (c) through (o) of this provision. (End of Provision) 18. The Following Provisions Are Incorporated By Full Text: FAR 52.212-2 Evaluation - Commercial Items (Oct 2014) (a) The Government will award a contract resulting from this solicitation to the responsible offeror whose offer conforming to the solicitation will be most advantageous to the Government, price and other factors considered. The following factors shall be used to evaluate offers: •(i) price •(ii) JCI Certified Technician with 3 years experience Award will be made on the basis of the price and other factors in accordance with FAR 13.106-2. (b) Options. The Government will evaluate offers for award purposes by adding the total price for all options to the total price for the basic requirement. The Government may determine that an offer is unacceptable if the option prices are significantly unbalanced. Evaluation of options shall not obligate the Government to exercise the option(s). (c) A written notice of award or acceptance of an offer, mailed or otherwise furnished to the successful offeror within the time for acceptance specified in the offer, shall result in a binding contract without further action by either party. Before the offer's specified expiration time, the Government may accept an offer (or part of an offer), whether or not there are negotiations after its receipt, unless a written notice of withdrawal is received before award. (End of Provision) 52.217-5 Evaluation of Options Except when it is determined in accordance with FAR 17.206(b) not to be in the Government's best interests, the Government will evaluate offers for award purposes by adding the total price for all options to the total price for the basic requirement. Evaluation of options will not obligate the Government to exercise the option(s). (End of Provision) 52.219-1 Alt I Small Business Program Representations (Oct 2014) (a) Definitions. As used in this provision-- "Economically disadvantaged women-owned small business (EDWOSB) concern" means a small business concern that is at least 51 percent directly and unconditionally owned by, and the management and daily business operations of which are controlled by, one or more women who are citizens of the United States and who are economically disadvantaged in accordance with 13 CFR part 127. It automatically qualifies as a women-owned small business concern eligible under the WOSB Program. "Service-disabled veteran-owned small business concern"-- (1) Means a small business concern-- (i) Not less than 51 percent of which is owned by one or more service-disabled veterans or, in the case of any publicly owned business, not less than 51 percent of the stock of which is owned by one or more service-disabled veterans; and (ii) The management and daily business operations of which are controlled by one or more service-disabled veterans or, in the case of a service-disabled veteran with permanent and severe disability, the spouse or permanent caregiver of such veteran. (2) "Service-disabled veteran" means a veteran, as defined in 38 U.S.C. 101(2), with a disability that is service-connected, as defined in 38 U.S.C. 101(16). "Small business concern" means a concern, including its affiliates, that is independently owned and operated, not dominant in the field of operation in which it is bidding on Government contracts, and qualified as a small business under the criteria in 13 CFR Part 121 and the size standard in paragraph (b) of this provision. "Small disadvantaged business concern, consistent with 13 CFR 124.1002," means a small business concern under the size standard applicable to the acquisition, that-- (1) Is at least 51 percent unconditionally and directly owned (as defined at 13 CFR 124.105) by-- (i) One or more socially disadvantaged (as defined at 13 CFR 124.103) and economically disadvantaged (as defined at 13 CFR 124.104) individuals who are citizens of the United States, and (ii) Each individual claiming economic disadvantage has a net worth not exceeding $750,000 after taking into account the applicable exclusions set forth at 13 CFR 124.104(c)(2); and (2) The management and daily business operations of which are controlled (as defined at 13 CFR 124.106) by individuals who meet the criteria in paragraphs (1)(i) and (ii) of this definition. "Veteran-owned small business concern" means a small business concern-- (1) Not less than 51 percent of which is owned by one or more veterans (as defined at 38 U.S.C. 101(2)) or, in the case of any publicly owned business, not less than 51 percent of the stock of which is owned by one or more veterans; and (2) The management and daily business operations of which are controlled by one or more veterans. "Women-owned small business concern" means a small business concern-- (1) That is at least 51 percent owned by one or more women; or, in the case of any publicly owned business, at least 51 percent of the stock of which is owned by one or more women; and (2) Whose management and daily business operations are controlled by one or more women. "Women-owned small business (WOSB) concern eligible under the WOSB Program (in accordance with 13 CFR part 127)," means a small business concern that is at least 51 percent directly and unconditionally owned by, and the management and daily business operations of which are controlled by, one or more women who are citizens of the United States. (b) (1) The North American Industry Classification System (NAICS) code for this acquisition is 334511. (2) The small business size standard is 1250 employees. (3) The small business size standard for a concern which submits an offer in its own name, other than on a construction or service contract, but which proposes to furnish a product which it did not itself manufacture, is 500 employees. (c) Representations. (1) The offeror represents as part of its offer that it [_] is, [_] is not a small business concern. (2) [ Complete only if the offeror represented itself as a small business concern in paragraph (c)(1) of this provision. ] The offeror represents that it [_] is, [_] is not, a small disadvantaged business concern as defined in 13 CFR 124.1002. (3) [ Complete only if the offeror represented itself as a small business concern in paragraph (c)(1) of this provision. ] The offeror represents as part of its offer that it [_] is, [_] is not a women-owned small business concern. (4) Women-owned small business (WOSB) concern eligible under the WOSB Program. [Complete only if the offeror represented itself as a women-owned small business concern in paragraph (c)(3) of this provision.] The offeror represents as part of its offer that- (i) It [_] is, [_] is not a WOSB concern eligible under the WOSB Program, has provided all the required documents to the WOSB Repository, and no change in circumstances or adverse decisions have been issued that affects its eligibility; and (ii) It [_] is, [_] is not a joint venture that complies with the requirements of 13 CFR part 127, and the representation in paragraph (c)(4)(i) of this provision is accurate for each WOSB concern eligible under the WOSB Program participating in the joint venture. [The offeror shall enter the name or names of the WOSB concern eligible under the WOSB Program and other small businesses that are participating in the joint venture: _________.] Each WOSB concern eligible under the WOSB Program participating in the joint venture shall submit a separate signed copy of the WOSB representation. (5) Economically disadvantaged women-owned small business (EDWOSB) concern. [Complete only if the offeror represented itself as a women-owned small business concern eligible under the WOSB Program in (c)(4) of this provision.] The offeror represents as part of its offer that-- (i) It [_] is, [_] is not an EDWOSB concern eligible under the WOSB Program, has provided all the required documents to the WOSB Repository, and no change in circumstances or adverse decisions have been issued that affects its eligibility; and (ii) It [_] is, [_] is not a joint venture that complies with the requirements of 13 CFR part 127, and the representation in paragraph (c)(5)(i) of this provision is accurate for each EDWOSB concern participating in the joint venture. [The offeror shall enter the name or names of the EDWOSB concern and other small businesses that are participating in the joint venture: _____________.] Each EDWOSB concern participating in the joint venture shall submit a separate signed copy of the EDWOSB representation. (6) [ Complete only if the offeror represented itself as a small business concern in paragraph (c)(1) of this provision. ] The offeror represents as part of its offer that it [_] is, [_] is not a veteran-owned small business concern. (7) [ Complete only if the offeror represented itself as a veteran-owned small business concern in paragraph (c)(6) of this provision. ] The offeror represents as part of its offer that is [_] is, [_] is not a service-disabled veteran-owned small business concern. (8) [ Complete only if the offeror represented itself as a small business concern in paragraph (c)(1) of this provision.] The offeror represents, as part of its offer, that - (i) It [_] is, [_] is not a HUBZone small business concern listed, on the date of this representation, on the List of Qualified HUBZone Small Business Concerns maintained by the Small Business Administration, and no material changes in ownership and control, principal office, or HUBZone employee percentage have occurred since it was certified in accordance with 13 CFR part 126; and (ii) It [_] is, [_] is not a HUBZone joint venture that complies with the requirements of 13 CFR part 126, and the representation in paragraph (c)(8)(i) of this provision is accurate for each HUBZone small business concern participating in the HUBZone joint venture. [ The offeror shall enter the names of each of the HUBZone small business concerns participating in the HUBZone joint venture: _ __________.] Each HUBZone small business concern participating in the HUBZone joint venture shall submit a separate signed copy of the HUBZone representation. (d) Notice. (1) If this solicitation is for supplies and has been set aside, in whole or in part, for small business concerns, then the clause in this solicitation providing notice of the set-aside contains restrictions on the source of the end items to be furnished. (2) Under 15 U.S.C. 645(d), any person who misrepresents a firm's status as a business concern that is small, HUBZone small, small disadvantaged, service-disabled veteran-owned small, economically disadvantaged women-owned small, or women-owned small eligible under the WOSB Program in order to obtain a contract to be awarded under the preference programs established pursuant to section 8, 9, 15, 31, and 36 of the Small Business Act or any other provision of Federal law that specifically references section 8(d) for a definition of program eligibility, shall -- (i) Be punished by imposition of fine, imprisonment, or both; (ii) Be subject to administrative remedies, including suspension and debarment; and (iii) Be ineligible for participation in programs conducted under the authority of the Act. (End of Provision) Alternate I (Sep 2015). As prescribed in 19.309 (a)(2), add the following paragraph (c)(9) to the basic provision: (9) [Complete if offeror represented itself as disadvantaged in paragraph (c)(2) of this provision.] The offeror shall check the category in which its ownership falls: ___ Black American. ___ Hispanic American. ___ Native American (American Indians, Eskimos, Aleuts, or Native Hawaiians). ___ Asian-Pacific American (persons with origins from Burma, Thailand, Malaysia, Indonesia, Singapore, Brunei, Japan, China, Taiwan, Laos, Cambodia (Kampuchea), Vietnam, Korea, The Philippines, Republic of Palau, Republic of the Marshall Islands, Federated States of Micronesia, the Commonwealth of the Northern Mariana Islands, Guam, Samoa, Macao, Hong Kong, Fiji, Tonga, Kiribati, Tuvalu, or Nauru). ___ Subcontinent Asian (Asian-Indian) American (persons with origins from India, Pakistan, Bangladesh, Sri Lanka, Bhutan, the Maldives Islands, or Nepal). ___ Individual/concern, other than one of the preceding. (End of Provision) 52.237-1 -- Site Visi t (Apr 1984) Offerors or quoters are urged and expected to inspect the site where services are to be performed and to satisfy themselves regarding all general and local conditions that may affect the cost of contract performance, to the extent that the information is reasonably obtainable. In no event shall failure to inspect the site constitute grounds for a claim after contract award. (End of Provision) FAR 52.252-1 -- Solicitation Provisions Incorporated by Reference (FEB 1998) This solicitation incorporates one or more solicitation provisions by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. The offeror is cautioned that the listed provisions may include blocks that must be completed by the offeror and submitted with its quotation or offer. In lieu of submitting the full text of those provisions, the offeror may identify the provision by paragraph identifier and provide the appropriate information with its quotation or offer. Also, the full text of a solicitation provision may be accessed electronically at http://farsite.hill.af.mil. (End of Provision) 19. The Following Provisions are Incorporated by Reference: FAR 52.209-5 Certification Regarding Debarment, Suspension, Proposed Debarment and Other Responsibility Matters (APR 2010) FAR 52.212-1, Instructions to Offerors - Commercial Items (APR 2014) FAR 52.212-3 Alt I Offeror Representations and Certifications--Commercial Items (MAR 2015) 20. The Following Clauses Are Incorporated By Reference: FAR 52.204-10 Reporting Executive Compensation and First-Tier Subcontract Awards (OCT 2015) FAR 52.204-19 Incorporation by Reference of Representations and Certifications (DEC 2014) FAR 52.212-4 Contracts Terms and Conditions - Commercial Items FAR 52.219-6 Notice of Total Small Business Set-Aside (NOV 2011) FAR 52.219-28 Post-Award Small Business Program Representation (JUL 2013) FAR 52.222-22 Previous Contracts and Compliance Reports FAR 52.222-25 Affirmative Action Compliance FAR 52.222-42 Statement of Equivalent Rates for Federal Hires FAR 52.223-18 Encouraging Contractor Policies to Ban Text Messaging While Driving (AUG 2011) FAR 52.232-8 Discounts for Prompt Payment (FEB 2002) FAR 52.232-11 Extras (APR 1984) FAR 52.232-39 Unenforceability of Unauthorized Obligations (JUN 2013) FAR 52.233-4 Applicable Law for Breach of Contract Claim (OCT 2014) FAR52.237-2 Protection of Government Buildings, Equipment, And Vegetation (APR 1984) FAR 52.253-1 Computer Generated Forms (JAN 1991) DFARS 252.203-7002 Requirement to Inform Employees of Whistleblower Rights (SEP 2013) DFARS 252.204-7003 Control of Government Personnel Work Product (APR 1992) DFARS 252.204-7012 Safeguarding of Unclassified Controlled Technical Information (NOV 2013) DFARS 252.223-7006 Prohibition On Storage And Disposal Of Toxic And Hazardous Materials DFARS 252.223-7008 Prohibition of Hexavalent Chromium (JUN 2013) DFARS 252-225-7048 Export-Controlled Items (JUN 2013) DFARS 252.232-7003 Electronic Submission of Payment Requests and Receiving Reports (JUN 2012) 20. The Following Clauses Are Incorporated By Full Text: FAR 52.212-5 CONTRACT TERMS AND CONDITIONS REQUIRED TO IMPLEMENT STATUTES OR EXECUTIVE ORDERS--COMMERCIAL ITEMS (DEVIATION 2013-O0019) (JUN 2016) (a) Comptroller General Examination of Record. The Contractor shall comply with the provisions of this paragraph (a) if this contract was awarded using other than sealed bid, is in excess of the simplified acquisition threshold, and does not contain the clause at 52.215-2, Audit and Records -- Negotiation. (1) The Comptroller General of the United States, or an authorized representative of the Comptroller General, shall have access to and right to examine any of the Contractor's directly pertinent records involving transactions related to this contract. (2) The Contractor shall make available at its offices at all reasonable times the records, materials, and other evidence for examination, audit, or reproduction, until 3 years after final payment under this contract or for any shorter period specified in FAR Subpart 4.7, Contractor Records Retention, of the other clauses of this contract. If this contract is completely or partially terminated, the records relating to the work terminated shall be made available for 3 years after any resulting final termination settlement. Records relating to appeals under the disputes clause or to litigation or the settlement of claims arising under or relating to this contract shall be made available until such appeals, litigation, or claims are finally resolved. (3) As used in this clause, records include books, documents, accounting procedures and practices, and other data, regardless of type and regardless of form. This does not require the Contractor to create or maintain any record that the Contractor does not maintain in the ordinary course of business or pursuant to a provision of law. (b) (1) Notwithstanding the requirements of any other clause in this contract, the Contractor is not required to flow down any FAR clause, other than those in this paragraph (b)(1) in a subcontract for commercial items. Unless otherwise indicated below, the extent of the flow down shall be as required by the clause- (i) 52.203-13, Contractor Code of Business Ethics and Conduct (Apr 2010) (41 U.S.C. 3509). (ii) 52.219-8, Utilization of Small Business Concerns (Oct 2014) (15 U.S.C. 637(d)(2) and (3)), in all subcontracts that offer further subcontracting opportunities. If the subcontract (except subcontracts to small business concerns) exceeds $650,000 ($1.5 million for construction of any public facility), the subcontractor must include 52.219-8 in lower tier subcontracts that offer subcontracting opportunities. (iii) 52.222-17, Nondisplacement of Qualified Workers (May 2014) (E.O. 13495). Flow down required in accordance with paragraph (1) of FAR clause 52.222-17. (iv) 52.222-21, Prohibition of Segregated Facilities (Apr 2015). (v) 52.222-26, Equal Opportunity (Apr 2015) (E.O. 11246). (vi) 52.222-35, Equal Opportunity for Veterans (Oct 2015) (38 U.S.C. 4212). (vii) 52.222-36, Equal Opportunity for Workers with Disabilities (Jul 2014) (29 U.S.C. 793). (viii) 52.222-37, Employment Reports on Veterans (Feb 2016) (38 U.S.C. 4212). (ix) 52.222-40, Notification of Employee Rights Under the National Labor Relations Act (Dec 2010) (E.O. 13496). Flow down required in accordance with paragraph (f) of FAR clause 52.222-40. (x) 52.222-41, Service Contract Labor Standards (May 2014), (41 U.S.C. chapter 67). (xi) _ X __ (A) 52.222-50, Combating Trafficking in Persons (Mar 2015) (22 U.S.C. chapter 78 and E.O. 13627). ___ (B) Alternate I (Mar 2015) of 52.222-50 (22 U.S.C. chapter 78 E.O. 13627). (xii) 52.222-51, Exemption from Application of the Service Contract Labor Standards to Contracts for Maintenance, Calibration, or Repair of Certain Equipment--Requirements (May 2014) (41 U.S.C. chapter 67.) (xiii) 52.222-53, Exemption from Application of the Service Contract Labor Standards to Contracts for Certain Services--Requirements (May 2014) (41 U.S.C. chapter 67) (xiv) 52.222-54, Employment Eligibility Verification (Oct 2015). (xv) 52.222-55, Minimum Wages Under Executive Order 13658 (Dec 2015) (E.O. 13658). (xvi) 52.225-26, Contractors Performing Private Security Functions Outside the United States (Jul 2013) (Section 862, as amended, of the National Defense Authorization Act for Fiscal Year 2008; 10 U.S.C. 2302 Note). (xvii) 52.226-6, Promoting Excess Food Donation to Nonprofit Organizations. (May 2014) (42 U.S.C. 1792). Flow down required in accordance with paragraph (e) of FAR clause 52.226-6. (xviii) 52.247-64, Preference for Privately-Owned U.S. Flag Commercial Vessels (Feb 2006) (46 U.S.C. Appx 1241(b) and 10 U.S.C. 2631). Flow down required in accordance with paragraph (d) of FAR clause 52.247-64. (xviii) 52.247-64, Preference for Privately-Owned U.S. Flag Commercial Vessels (Feb 2006) (46 U.S.C. Appx 1241(b) and 10 U.S.C. 2631). Flow down required in accordance with paragraph (d) of FAR clause 52.247-64. (2) While not required, the contractor may include in its subcontracts for commercial items a minimal number of additional clauses necessary to satisfy its contractual obligations. (End of Clause) 52.217-8 -- Option to Extend Services The Government may require continued performance of any services within the limits and at the rates specified in the contract. These rates may be adjusted only as a result of revisions to prevailing labor rates provided by the Secretary of Labor. The option provision may be exercised more than once, but the total extension of performance hereunder shall not exceed 6 months. The Contracting Officer may exercise the option by written notice to the Contractor within 60 days for the preliminary and 30 days to exercise the option. (End of Clause) 52.217-9 -- Option to Extend the Term of the Contract a) The Government may extend the term of this contract by written notice to the Contractor within 10 days of the end of the period of performance ; provided that the Government gives the Contractor a preliminary written notice of its intent to extend at least 10 days before the contract expires. The preliminary notice does not commit the Government to an extension. (b) If the Government exercises this option, the extended contract shall be considered to include this option clause. (c) The total duration of this contract, including the exercise of any options under this clause, shall not exceed 5 years and 6 months. 252.211-7003 ITEM UNIQUE IDENTIFICATION AND VALUATION (MAR2016) (a) Definitions. As used in this clause- Automatic identification device means a device, such as a reader or interrogator, used to retrieve data encoded on machine-readable media. Concatenated unique iten1 identifier means- ( l) For items that are serialized within the enterprise identifier, the linking together of the unique identifier data elements in order of the issuing agency code, enterprise identifier, and unique serial number within the enterprise identifier; or (2) For items that are serialized within the original part, lot, or batch number, the linking together of the unique identifier data elements in order of the issuing agency code; enterprise identifier; original part, lot, or batch number; and serial number within the original part, lot, or batch number. Data Matrix means a two-dimensional matrix symbology, which is made up of square or, in some cases, round modules arranged within a perimeter finder pattern and uses the Error Checking and Correction 200 (ECC200) specification found within International Standards Organization (ISO)/lnternational Electrotechnical Commission (IEC) 16022. Data qualifier means a specified character (or string of characters) that immediately precedes a data field that defines the general category or intended use ofthe data that follows. DoD recognized unique identification equivalent means a unique identification method that is in commercial use and has been recognized by DoD. All DoD recognized unique identification equivalents are listed at http://www. acq. osd.mil/dpap/pdi/uid/iuid _ equi valents.htmI. DoD item unique identification means a system of marking items delivered to DoD with unique item identifiers that have machine-readable data elements to distinguish an item from all other like and unlike items. For items that are serialized within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier and a unique serial number. For items that are serialized within the part, lot, or batch number within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier; the original part, lot, or batch number; and the serial number. Enterprise means the entity (e.g., a manufacturer or vendor) responsible for assigning unique item identifiers to items. Enterprise identifier means a code that is uniquely assigned to an enterprise by an issuing agency. Government's unit acquisition cost means- (1) For fixed-price type line, subline, or exhibit line items, the unit price identified in the contract at the time of delivery; (2) For cost-type or undefinitized line, subline, or exhibit line items, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery; and (3) For items produced under a time-and~materials contract, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery. Issuing agency means an organization responsible for assigning a globally unique identifier to an enterprise, as indicated in the Register of Issuing Agency Codes for ISO/I EC 15459, located at http:/www.aimglobal.org/?Reg_Authority15459. Issuing agency code means a code that designates the registration (or controlling) authority for the enterprise identifier. Item means a single hardware article or a single unit formed by a grouping of subassemblies, components, or constituent parts. Lot or batch number means an identifying number assigned by the enterprise to a designated group of items, usually referred to as either a lot or a batch, all of which were manufactured under identical conditions. Machine-readable means an automatic identification technology media, such as bar codes, contact memory buttons, radio frequency identification, or optical memory cards. Original part number means a combination of numbers or letters assigned by the enterprise at item creation to a class of items with the same form, fit, function, and interface. Parent item means the item assembly, intermediate component, or subassembly that has an embedded item with a unique item identifier or DoD recognized unique identification equivalent. Serial number within the enterprise identifier means a combination of numbers, letters, or symbols assigned by the enterprise to an item that provides for the differentiation of that item from any other like and unlike item and is never used again within the enterprise. Serial number within the part, lot, or batch number means a combination of numbers or letters assigned by the enterprise to an item that provides for the differentiation of that item from any other like item within a part, lot, or batch number assignment. Serialization within the enterprise identifier means each item produced is assigned a serial number that is unique among all the tangible items produced by the enterprise and is never used again. The enterprise is responsible for ensuring unique serialization within the enterprise identifier. Serialization within the part, lot, or batch number means each item of a particular part, lot, or batch number is assigned a unique serial number within that part, lot, or batch number assignment. The enterprise is responsible for ensuring unique serialization within the part, lot, or batch number within the enterprise identifier. Type designation means a combination of letters and numerals assigned by the Government to a major end item, assembly or subassembly, as appropriate, to provide a convenient means of differentiating between items having the same basic name and to indicate modifications and changes thereto. Unique item identifier means a set of data elements marked on items that is globally unique and unambiguous. The term includes a concatenated unique item identifier or a DoD recognized unique identification equivalent. Unique item identifier type means a designator to indicate which method of uniquely identifying a part has been used. The current list of accepted unique item identifier types is maintained at http://www. acq. osd.mil/dpap/pdi/uid/uii_ types.html. (b) The Contractor shall deliver all items under a contract line, subline, or exhibit line item. (c) Unique item identifier. (1) The Contractor shall provide a unique item identifier for the following: (i) Delivered items for which the Government's unit acquisition cost is $5,000 or more, except for the following line items: Contract line, subline, or exhibit line item No. Item description (ii) Items for which the Government's unit acquisition cost is less than $5,000 that are identified in the Schedule or the following table: Contract line, subline, or exhibit line item No. Item description (If items are identified in the Schedule, insert ''See Schedule" in this table.) (iii) Subassemblies, components, and parts embedded within delivered items, items with warranty requirements, DoD serially managed reparables and DoD serially managed nonreparables as specified in Attachment Number----. (iv) Any item of special tooling or special test equipment as defined in FAR 2.101 that have been designated for preservation and storage for a Major Defense Acquisition Program as specified in Attachment Number----. (v) Any item not included in paragraphs (c)(l)(i), (ii), (iii), or (iv) of this clause for which the contractor creates and marks a unique item identifier for traceability. (2) The unique item identifier assignment and its component data element combination shall not be duplicated on any other item marked or registered in the DoD Item Unique Identification Registry by the contractor. (3) The unique item identifier component data elements shall be marked on an item using two dimensional data matrix symbology that complies with ISO/IEC International Standard 16022, Information technology--lnternational symbology specification--Data matrix; ECC200 data matrix specification. (4) Data syntax and semantics of unique item identifiers. The Contractor shall ensure that- (i) The data elements (except issuing agency code) of the unique item identifier are encoded within the data matrix symbol that is marked on the item using one of the following three types of data qualifiers, as determined by the Contractor: (A) Application Identifiers (Als) (F'onnat Indicator 05 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology--EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard. (B) Data Identifiers (Dls) (Format Indicator 06 of lSO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology--EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard. (C) Text Element Identifiers (TEIs) (Format Indicator 12 of ISO/IEC International Standard 15434), in accordance with the Air Transport Association Common Support Data Dictionary; and (ii) The encoded data elements of the unique item identifier conform to the transfer structure, syntax, and coding of messages and data formats specified for Format Indicators 05, 06, and 12 in ISO/IEC International Standard 15434, Information Technology-Transfer Syntax for High Capacity Automatic Data Capture Media. (5) Unique item identifier. •(i) The Contractor shall- •(A) Determine whether to- (1) Serialize within the enterprise identifier; (2) Serialize within the part, lot, or batch number; or (3) Use a DoD recognized unique identification equivalent (e.g. Vehicle Identification Number); and (B) Place the data elements of the unique item identifier (enterprise identifier; serial number; DoD recognized unique identification equivalent; and for serialization within the part, lot, or batch number only: Original part, lot, or batch number) on items requiring marking by paragraph (c)(l) of this clause, based on the criteria provided in MIL-STD- 130, Identification Marking of U.S. Military Property, latest version; (C) Label shipments, storage containers and packages that contain uniquely identified items in accordance with the requirements of MIL-STD-129, Military Marking for Shipment and Storage, latest version; and (D) Verify that the marks on items and labels on shipments, storage containers, and packages are machine readable and conform to the applicable standards. The contractor shall use an automatic identification technology device for this verification that has been programmed to the requirements of Appendix A, MIL-STD-130, latest version. •(ii) The issuing agency code- (A) Shall not be placed on the item; and (B) Shall be derived from the data qualifier for the enterprise identifier. (d) For each item that requires item unique identification under paragraph (c)(l)(i), (ii), or (iv) of this clause or when item unique identification is provided under paragraph (c)(l)(v), in addition to the information provided as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the Contractor shall report at the time of delivery, as part of the Material Inspection and Receiving Report, the following information: (l) Unique item identifier. (2) Unique item identifier type. (3) Issuing agency code (if concatenated unique item identifier is used). (4) Enterprise identifier (if concatenated unique item identifier is used). (5) Original part number (if there is serialization within the original part number). (6) Lot or batch number (if there is serialization within the lot or batch number). (7) Current part number (optional and only if not the same as the original part number). (8) Current part number effective date (optional and only if current part number is used). (9) Serial number (if concatenated unique item identifier is used). (10) Government's unit acquisition cost. (11) Unit of measure. (12) Type designation of the item as specified in the contract schedule, if any. (13) Whether the item is an item of Special Tooling or Special Test Equipment. (14) Whether the item is covered by a warranty. (e) For embedded subassemblies, components, and parts that require DoD unique item identification under paragraph (c)(1)(iii) of this clause, the Contractor shall report as part of, or associated with, the Material Inspection and Receiving Report specified elsewhere in this contract, the following information: (1) Unique item identifier of the parent item under paragraph (c)(1) of this clause that contains the embedded subassembly, component, or part. (2) Unique item identifier of the embedded subassembly, component, or part. (3) Unique item identifier type.** (4) Issuing agency code (if concatenated unique item identifier is used).** (5) Enterprise identifier (if concatenated unique item identifier is used).** (6) Original part number (if there is serialization within the original part number).** (7) Lot or batch number (if there is serialization within the lot or batch number).** (8) Current part number (optional and only if not the same as the original part number).** (9) Current part number effective date (optional and only if current part number is used).** (10) Serial number (if concatenated unique item identifier is used).** (11) Description. ** Once per item. (f) The Contractor shall submit the infonnation required by paragraphs (d) and (e) of this clause as follows: (l) End items shall be reported using the receiving report capability in Wide Area WorkFlow (WAWF) in accordance with the clause at 252.232-7003. If WAWF is not required by this contract, and the contractor is not using WAWF, follow the procedures at http://dodprocurementtoolbox.com/site/uidregistry/. (2) Embedded items shall be reported by one ofthe following methods- (i) Use of the embedded items capability in WAWF; (ii) Direct data submission to the IUID Registry following the procedures and formats at http://dodprocurementtoolbox.com/site/uidregistry/; or (iii) Via WAWF as a deliverable attachment for exhibit line item number 0001, Unique Item Identifier Report for Embedded Items, Contract Data Requirements List, DD Form 1423. (g) Subcontracts. If the Contractor acquires by subcontract any items for which item unique identification is required in accordance with paragraph (c)(I) of this clause, the Contractor shall include this clause, including this paragraph (g), in the applicable subcontract(s), including subcontracts for commercial items. (End of clause) 252.232-7006 WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (MAY 2013) (a) Definitions. As used in this clause- Department of Defense Activity Address Code (DoDAAC) is a six position code that uniquely identifies a unit, activity, or organization. Document type means the type of payment request or receiving report available for creation in Wide Area Workflow (WAWF). Local processing office (LPO) is the office responsible for payment certification when payment certification is done external to the entitlement system. (b) Electronic invoicing. The WAWF system is the method to electronically process vendor payment requests and receiving reports, as authorized by DFARS 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports. (c) WAWF access. To access WAWF, the Contractor shall- (1) Have a designated electronic business point of contact in the System for Award Management at https://www.acquisition.gov ; and (2) Be registered to use WAWF at https://wawfeb.mil/ following the step-by-step procedures for self-registration available at this Web site. (d) WAWF training. The Contractor should follow the training instructions of the WAWF Web-Based Training Course and use the Practice Training Site before submitting payment requests through WAWF. Both can be accessed by selecting the "Web Based Training" link on the WAWF home page at https://wawfeb.mil/. (e) WAWF methods of document submission. Document submissions may be via Web entry, Electronic Data Interchange, or File Transfer Protocol. (f) WAWF payment instructions. The Contractor must use the following information when submitting payment requests and receiving reports in WAWF for this contract/order: (1) Document type. The Contractor shall use the following document type(s). FFP (Contracting Officer: Insert applicable document type(s). Note: If a "Combo" document type is identified but not supportable by the Contractor's business systems, an "Invoice" (stand-alone) and "Receiving Report" (stand-alone) document type may be used instead.) (2) Inspection/acceptance location. The Contractor shall select the following inspection/acceptance location(s) in WAWF, as specified by the contracting officer. Roland Hartz (Contracting Officer: Insert inspection and acceptance locations or "Not applicable".) (3) Document routing. The Contractor shall use the information in the Routing Data Table below only to fill in applicable fields in WAWF when creating payment requests and receiving reports in the system. Routing Data Table* Field Name in WAWF Data to be entered in WAWF Pay Official DoDAAC F03000 Issue By DoDAAC FA2835 Admin DoDAAC FA2835 Inspect By DoDAAC F2B3AQ Ship To Code F2B3AQ Ship From Code Contractors Cage Code Mark For Code Service Approver (DoDAAC) F2B3AQ Service Acceptor (DoDAAC) FA2835 Accept at Other DoDAAC LPO DoDAAC DCAA Auditor DoDAAC Other DoDAAC(s) (*Contracting Officer: Insert applicable DoDAAC information or "See schedule" if multiple ship to/acceptance locations apply, or "Not applicable.") (4) Payment request and supporting documentation. The Contractor shall ensure a payment request includes appropriate contract line item and subline item descriptions of the work performed or supplies delivered, unit price/cost per unit, fee (if applicable), and all relevant back-up documentation, as defined in DFARS Appendix F, (e.g. timesheets) in support of each payment request. (5) WAWF email notifications. The Contractor shall enter the email address identified below in the "Send Additional Email Notifications" field of WAWF once a document is submitted in the system. Sharley.robertson@us.af.mil benjamin.tuckerman.1@us.af.mil (Contracting Officer: Insert applicable email addresses or "Not applicable.") (g) WAWF point of contact. (1) The Contractor may obtain clarification regarding invoicing in WAWF from the following contracting activity's WAWF point of contact. Brian.Dwyer.6@us.af.mil Delton. Davison@us.af.mil (Contracting Officer: Insert applicable infonnation or "Not applicable.") (2) For technical WAWF help, contact the WAWF helpdesk at 866-618-5988. (End of clause) FAR 52.252-2 -- Clauses Incorporated by Reference (Feb 1998) This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this address: http://farsite.hill.af.mil/farsite.html (End of Clause) AFFARS 5352.201-9101 OMBUDSMAN (APR 2014) (a) An ombudsman has been appointed to hear and facilitate the resolution of concerns from offerors, potential offerors, and others for this acquisition. When requested, the ombudsman will maintain strict confidentiality as to the source of the concern. The existence of the ombudsman does not affect the authority of the program manager, contracting officer, or source selection official. Further, the ombudsman does not participate in the evaluation of proposals, the source selection process, or the adjudication of protests or formal contract disputes. The ombudsman may refer the interested party to another official who can resolve the concern. (b) Before consulting with an ombudsman, interested p arties must first address their concerns, issues, disagreements, and/or recommendations to the contracting officer for resolution. Consulting an ombudsman does not alter or postpone the timelines for any other processes (e.g., agency level bid protests, GAO bid protests, requests for debriefings, employee-employer actions, contests of OMB Circular A-76 competition performance decisions). (c) If resolution cannot be made by the contracting officer, the interested party may contact the ombudsman, Lt Col Kenneth L. Decker, Jr. Ombudsman AFLCMC/AQP Acquisition Excellence Directorate Phone: 785-2246 Email: kenneth.decker.1@us.af.mil 1790 10th Street Bldg 572 Wright Patterson AFB OH 45433-7630 Concerns, issues, disagreements, and recommendations that cannot be resolved at the Center/MAJCOM/DRU or AFISRA level, may be brought by the interested party for further consideration to the Air Force ombudsman, Associate Deputy Assistant Secretary (ADAS) (Contracting), SAF/AQC, 1060 Air Force Pentagon, Washington DC 20330-1060, phone number (571) 256-2397, facsimile number (571) 256-2431. (d) The ombudsman has no authority to render a decision that binds the agency. (e) Do not contact the ombudsman to request copies of the solicitation, verify offer due date, or clarify technical requirements. Such inquiries shall be directed to the Contracting Officer. (End of clause) AFFARS 5352.223-9000 Elimination of Use of Class I Ozone Depleting Substances (ODS) (NOV 2012) (a) Contractors shall not: (1) Provide any service or product with any specification, standard, drawing, or other document that requires the use of a Class I ODS in the test, operation, or maintenance of any system, subsystem, item, component, or process; or (2) Provide any specification, standard, drawing, or other document that establishes a test, operation, or maintenance requirement that can only be met by use of a Class I ODS as part of this contract/order. [Note: This prohibition does not apply to manufacturing. (b) For the purposes of Air Force policy, the following products that are pure (i.e., they meet the relevant product specification identified in AFI 32-7086 ) are Class I ODSs: (1) Halons: 1011, 1202, 1211, 1301, and 2402; (2) Chlorofluorocarbons (CFCs): CFC-11, CFC-12, CFC-13, CFC-111, CFC-112, CFC-113, CFC-114, CFC-115, CFC-211, CFC-212, CFC-213, CFC-214, CFC-215, CFC-216, and CFC-217, and the blends R-500, R-501, R-502, and R-503; and (3) Carbon Tetrachloride, Methyl Chloroform, and Methyl Bromide. [NOTE: Material that uses one or more of these Class I ODSs as minor constituents do not meet the Air Force definition of a Class I ODS.] (End of clause) AFFARS 5352.223-9001 Health and Safety on Government Installations (NOV 2012) (a) In performing work under this contract on a Government installation, the contractor shall: (1) Take all reasonable steps and precautions to prevent accidents and preserve the health and safety of contractor and Government personnel performing or in any way coming in contact with the performance of this contract; and (2) Take such additional immediate precautions as the contracting officer may reasonably require for health and safety purposes. (b) The contracting officer may, by written order, direct Air Force Occupational Safety and Health (AFOSH) Standards and/or health/safety standards as may be required in the performance of this contract and any adjustments resulting from such direction will be in accordance with the Changes clause of this contract. (c) Any violation of these health and safety rules and requirements, unless promptly corrected as directed by the contracting officer, shall be grounds for termination of this contract in accordance with the Default clause of this contract. (End of clause) 21. Defense Priorities and Allocations System (DPAS) and assigned rating, is not applicable.
Web Link: FBO.gov Permalink
(https://www.fbo.gov/spg/USAF/AFMC/ASC/FA2835-16-P-0034/listing.html)
Place of Performance: Address: 66ABG/CEIAR, 120 Grenier St, Hanscom AFB, Massachusetts, 01731, United States; Zip Code: 01731
Record: SN04280882-W 20160922/160921000148-7b86fec12aa10ce3fa1d3b6eb88ec4ea (fbodaily.com)
Source: FedBizOpps Link to This Notice
(may not be valid after Archive Date)

| FSG Index | This Issue's Index | Today's FBO Daily Index Page |

Loren Data's SAM Daily™

41 -- Chiller Controls Hanscom AFB