SOURCES SOUGHT
81 -- Drum Steel
- Notice Date
- 10/18/2016
- Notice Type
- Sources Sought
- NAICS
- 332431
— Metal Can Manufacturing
- Contracting Office
- Defense Logistics Agency, DLA Acquisition Locations, DLA Troop Support - Construction & Equipment, 700 Robbins Avenue, Philadelphia, Pennsylvania, 19111-5096, United States
- ZIP Code
- 19111-5096
- Solicitation Number
- SPE8ED17XXXXXX
- Archive Date
- 11/12/2016
- Point of Contact
- Michael Upshaw, Phone: 2157377387
- E-Mail Address
-
Michael.Upshaw@dla.mil
(Michael.Upshaw@dla.mil)
- Small Business Set-Aside
- Total Small Business
- Description
- This is a Sources Sought Notice only. DLA Troop Support Philadelphia is seeking to identify possible sources that can manufacturer and supply Drum, Steel, Hazmat NSN 8110-00-030-7780 and cataloged in Federal Supply Class (FSC) 8145. This is market research to locate potential sources of supply for the container. REMOVEABLE HEAD WITH NUT AND BOLT TYPE LOCKING RING. HAZARDOUS WASTE APPROVED. MINIMUM MATERIAL THICKNESS FOR LOCKING RING 2.40MM (0.0946 IN.). MINIMUM MATERIAL THICKNESS OF BOLT IS 15.875MM (0.625 IN.). MINIMUM LENGTH IS 88.9MM (3.500 IN.). RATED (MARKED) CAP. 208 LITERS (55 GAL.) & MINIMUM OVERALL CONTENT 216.5 LITERS (57.2 GAL.) MINIMUM HEIGHT WITHOUT COVER 864MM, + OR -3.18MM (34 IN., + OR - 0.125 IN.). MINIMUM INSIDE DIA. IS 572MM, + OR - 1.59MM (22.5 IN. < (>, <)> + OR - 0.0625 IN.). MINIMUM MATERIAL THICKNESS OF DRUM IS 1.10MM (0.0433 IN.). DRUM SHALL BE TESTED I.A.W. UN/POP 1A2/Y1.5/150. MARKINGS: DRUM SHALL BE MARKED I.A.W. UN RQMTS. PROTECTIVE COATING: COAT ALL EXTERIOR SURFACES OF THE DRUM (INCLUDING COMPONENT PARTS), EXCEPT THE CLOSING BOLT AND GASKET (WHEN SUPPLIED) < (>,<)> WITH A RUST INHIBITING COATING THAT WITHSTANDSTHE SALT SPRAY TEST REQUIREMENTS OF ASTM-B-117 UTILIZING A FIVE PERCENT SALT SOLUTION AT 35 DEGREES C (120 DEGREES F) FOR A MINIMUM EXPOSURE TIME OF 96 HOURS. RESULTS OF THE SALT SPRAY TEST SHALL SHOW NO RUST CREEPAGE, BLISTERING, UNDERCUTTING OR LOSS OF ADHESION OF THE PAINT BEYOND 1/8 INCH OF THE SCRIBE MARK. ALL OTHER SURFACES OF THE TEST SPECIMENS SHALL SHOW NO MORE THAN A TRACE OF FILM FAILURE, (RUST GRADE 9 OF ASTM-D-610), WITH NONE LARGER THAN 1MM, (3/64 INCH) IN DIAMETER. ACCEPTABLE COLORS, IAW FED STD 595, ARE AS FOLLOWS: NOS. 37038, 37030, 34082, 34083<(>,<)> 34086, 34089, 34092, 34102, 34127. BOLT & NUT SHALL BE INSTALLED TO THE LOCKING RING SO THEY WILL NOT BE LOST DURING SHIPMENT. DRUM SHALL BE FURNISHED FULLY ASSEMBLED. I.A.W. 49 CFR 178 SUBPART L AND SUBPART M CFR SECTION 178 AS APPLIES. IDENTIFY TO: MIL-STD-130N, 16 Nov 2012 IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY This is NOT a Request for Proposal, Request for Quote or Invitation for Bid. DLA is seeking sources of supply for the NSN listed above. Interested contractors should contact Michael Upshaw for further information at 215 737-7387 or Michael.Upshaw@dla.mil. The sources sought information is issued for the purposes of market research only and the Government is not obligated to purchase any materials as a result of this inquiry. Any resultant solicitation will be synopsized on https://www.dibbs.bsm.dla.mil/ website
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DLA/J3/DSCP-I/SPE8ED17XXXXXX/listing.html)
- Record
- SN04306548-W 20161020/161018233953-1383fb4ee62857e99e79b261465a1b0f (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |