SOURCES SOUGHT
20 -- FY 17 Dry-dock repairs to Coast Guard Cutter JUNIPER
- Notice Date
- 11/2/2016
- Notice Type
- Sources Sought
- NAICS
- 336611
— Ship Building and Repairing
- Contracting Office
- Department of Homeland Security, United States Coast Guard (USCG), USCG Surface Forces Logistics Center (SFLC) Procurement Branch 2, 1301 Clay St., Suite 807N, Oakland, California, 94612-5249, United States
- ZIP Code
- 94612-5249
- Solicitation Number
- DRYDOCK-REPAIRS-CGC-JUNIPER
- Archive Date
- 2/9/2017
- Point of Contact
- Andrew G. Jacobs, Phone: 5106375874
- E-Mail Address
-
Andrew.G.Jacobs@uscg.mil
(Andrew.G.Jacobs@uscg.mil)
- Small Business Set-Aside
- N/A
- Description
- The U.S. Coast Guard is looking for sources which would be interested in performing dry-dock repairs for Coast Guard Cutter JUNIPER. The performance period of this upcoming dry-dock is April 4, 2017 - June 14, 2017. It is anticipated requests for quotes will be issued approximately 22 November 2016 and the contract would be awarded approximately 3 February 2017. JUNIPER is a 225' Seagoing Buoy Tender home ported in Newport, RI. There are approximately 65 projected work items in the requirement and they are noted below. All repairs will take place at the awarded contractor's dry-dock. All contractor dry-dock facilities must be approved and certified by the U.S. Coast Guard. The is no geographical restriction for this vessel. Companies which would be interested in submitting a proposal for this requirement should reply to this sources sought notice noting their business size status such as large business, small business, HUBZone, Service-Disabled Veteran-owned, Women Owned Small Business etc.... Further if there are no past performance evaluations on file in the Past Performance Information System Retrieval database, contractors should provide a couple past performance references including the following information: contract numbers, project titles, dollar amounts, points of contact and telephone numbers. Replies should be sent by November 9, 2016, 3:30 pm Pacific Time to: Andrew.G.Jacobs@uscg.mil Shortly after receiving responses the Coast Guard will determine if this requirement will be set aside or unrestricted. After the determination a presolicitation notice and request for quote will be posted on this website (https://www.fbo.gov/). The NAICS Code is 336611. The small business size standard is less than 1250 employees. Contractors are reminded that in the case of a HUB Zone set-aside, FAR 52.219-3, "Notice of HUBZone Set-Aside or Sole Source Award" would apply which requires that at least 50 percent of the cost of personnel for contract performance be spent for employees of the concern or employees of other HUBZone small businesses. Contractors are also reminded that in the case of a Service-Disabled Veteran-Owned Small Business Set-Aside, FAR 52.219-27, "Notice of Service-Disabled Veteran-Owned Small Business Set-Aside" would apply which requires that at least 50 percent of the cost of personnel for contract performance be spent for employees of the concern or employees of other service disabled veteran owned small businesses. Additionally, regarding FAR 52.219-30 "Notice of Set A-Side For Women-Owned Small Business Concerns...": A women-owned small business (WOSB) concern eligible under the WOSB Program, means a small business concern that is at least 51 percent directly and unconditionally owned by, and the management and daily business operations of which are controlled by, one or more women who are citizens of the United States. JUNIPER Work Items D-001 Hull Plating (U/W Body), Inspect D-002 Hull Plating (U/W Body), Ultrasonic Testing D-003 Appendages (U/W), Leak Test O-004 Appendages (U/W) - Internal, Preserve D-005 Chain Locker(s), Clean and Inspect D-006 Voids (Non-Accessible), Leak Test O-007 Voids (Non-Accessible), Internal Surfaces, Preserve D-008 Tanks (MP Fuel Service), Clean and Inspect D-009 Tanks (Ballast), Clean and Inspect D-010 Propulsion Shafting; Remove, Inspect, and Reinstall D-011 Propulsion Shaft Seals, Mechanical Overhaul And Inflatable Renewal O-012 Propulsion Tail Shaft Sleeve, Skim Cut D-013 Controllable Pitch Propellers, Clean and Inspect D-014 Controllable Pitch Propeller, System Maintenance D-015 Controllable Pitch Propeller Hub, General Maintenance, Perform D-016 Fwd Scan Sonar Transducer, General Maintenance, Perform D-017 Sea Valves and Waster Pieces, Overhaul or Renew D-018 Sea Strainers - Duplex (All Sizes), Overhaul D-019 Sea Strainers - Simplex (All Sizes), Clean and Inspect D-020 Sea Bay, Clean and Inspect D-021 Sea Bay, Preserve 100% O-022 Rudder(s), Preserve ("100%") D-023 Rudder and Rudder Stock, Remove and Inspect D-024 Thruster Units (Bow And Stern), Overhaul D-030 Anchor Windlass, Inspect and Service D-031 Anchor Chain(s) and Ground Tackle, Inspect and Repair D-032 Warping Capstan, Inspect and Service D-033 Hull Fittings (Mooring and Towing), Inspect and Test D-034 Single Point Davit, Inspect and Service D-035 Twin Pivot Arm Davit, Inspect and Service D-036 Single Point Davit Exterior Surfaces, 100% Preserve D-037 Buoy Crane, Inspect And Service O-038 Tanks (Ballast), Preserve "Partial" D-039 Decks - Exterior (Buoy or Construction Deck), Preserve 100% O-040 U/W Body, Preserve (100%) O-041 U/W Body, Preserve (Partial - Condition A) O-042 U/W Body, Preserve (Partial - Condition B) O-043 U/W Body, Preserve (Partial - Condition C) O-044 Stern Tube Interior Surfaces, Preserve 100% D-045 Hull Plating Freeboard, Preserve "100%" D-046 Impressed Current Cathodic Protection System, Inspect and Maintain O-047 Impressed Current Cathodic Protection System Anodes, Renew O-048 Impressed Current Cathodic Protection System Reference Cells, Renew O-049 Impressed Current Cathodic Protection System Dielectric Shield, Repair O-050 Impressed Current Cathodic Protection System Dielectric Shield (Capastic Fairing), Renew D-051 Drydock D-052 Temporary Services, Provide - Cutter D-053 Sea Trial Performance, Support, Provide D-054 Bilges, Machinery Space, Clean and Inspect D-055 Main Mast, Preserve, 100% D-056 Links, Gripes, Binders and Jacks, Service, Inspect and Test D-057 Bilges, Preserve D-058 Main Diesel Engine Mounts, Upgrade D-059 SSDG, Heat Exchanger, Modify D-060 SSDG Isolation Mount, Renew D-063 Propulsion Shaft Fairwaters and Rope Guards, Inspect O-064 Propulsion Shaft Seals (Bulkhead), Overhaul D-065 Fathometer Transducer, General Maintenance D-061 LUBE OIL ISOLATION VALVE, INSTALLATION D-062 Stack Lighting, Install D-065 Auxiliary Sea Water System Valves, Overhaul Or Renew D-065 Sewage Piping, renew D-065 ASW Piping, Renew
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DHS/USCG/VPLMLCP/DRYDOCK-REPAIRS-CGC-JUNIPER /listing.html)
- Place of Performance
- Address: At the vendor's dry-dock facility to be determined., United States
- Record
- SN04318221-W 20161104/161102234052-d1d6ba19da6ef58e16f2f1eaf783e575 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |