Loren Data's SAM Daily™

fbodaily.com
Home Today's SAM Search Archives Numbered Notes CBD Archives Subscribe
FBO DAILY - FEDBIZOPPS ISSUE OF FEBRUARY 08, 2017 FBO #5556
SOLICITATION NOTICE

60 -- Pulse Selection System

Notice Date
2/6/2017
 
Notice Type
Presolicitation
 
NAICS
334516 — Analytical Laboratory Instrument Manufacturing
 
Contracting Office
Department of the Air Force, Air Force Materiel Command, AFRL/RIK - Rome, 26 Electronic Parkway, Rome, New York, 13441-4514, United States
 
ZIP Code
13441-4514
 
Solicitation Number
FA8751-17-Q-0148
 
Archive Date
3/31/2017
 
Point of Contact
Tabitha Haggart, Phone: 315-330-3787, Bryant (Lackland) Soule, Phone: 315-330-4723
 
E-Mail Address
Tabitha.Haggart@us.af.mil, bryant.soule@us.af.mil
(Tabitha.Haggart@us.af.mil, bryant.soule@us.af.mil)
 
Small Business Set-Aside
N/A
 
Description
This is a Notice of Proposed Contract Action under FAR Part 12 Acquisition of Commercial Items and FAR Part 13 Simplified Acquisition Procedures. This notice is for information only; a solicitation will not be issued. THIS IS NOT A REQUEST FOR PROPOSAL. The associated North American Industry Classification System (NAICS) code is 334516 with a size standard of 1000 employees. Brief Description of Requirement: AFRL requires the purchase of a pulse selection system that meets the following capabilities: Key system specifications: for Modulator with UV Option for use at 369M QTY- 1 • Pulse Selection: Single shot to multiple repetition rates 30MHz for mode-locked lasers up to 100MHz • Dispersion: Low temporal dispersion, compatible with fsec pulses with no spatial dispersion • Transmission: Optical Transmission of >80% • Pulse Width: Min. pulse width of 18ns measured at zero • Pulse Width Limit: No limit on pulse width • Offset: Center in/Center out operation, no offset or angular change Specifications for 25D Driver: Qty - 1 • Rise and Fall Time: <8ns (Typical with most Electro-Optic Modulators) • Output Voltage Swing: >175v P-P push-pull. (Output Voltage is adjustable from approximately, 140v to 15v by front panel control) • Output Impedance: 100 Ohm Balanced Line • Bias Voltage: Continuously adjustable between +/- 550v DC by front panel control • Input Signal: Either TTL Compatible or Unipolar 0-1V, selectable by internal switch on driver assembly • Input Impedance: 50 ohms, either mode • Input AC Power: 100VAC to 240VAC 50/60Hz. Set by internal push-pin selectable and is set at time of shipment. • Cooling: Forced air-cooling. (Total dissipation approx. 350W). • Dimensions: The dimensions are 45cm W x 44cm L x 17.5cm H. The weight is 32lbs • Environmental Conditions: Typical lab use. Specifications for Synchronous Countdown System: Qty - 1 • Input Clock Rate: Mode Locker Input, 10MHz Min, 70MHz Max External Input, 10Hz min, 140MHz Max • Countdown Range: F(clock)/2 min, f(clock)/1*10^6 max • Input-Output Jitter: <100ps, any count • Input Requirements: Mode Locker Input - sine wave, -6dbm min (112mv RMS), +15dbm,ax (1.3v RMS), Zi=50ohms • External Input - 100mv peak min, 1.5ns min pulse width. +/- 2v peak max. Zi=50ohms • Gate Input = TTL levels, min width one clock period. Burst ends one count after negative edge of gate input signal. Zi=50ohms • Single Shot Input = TTL levels, 10ns min pulse width. Zi=50ohms. • Delay: Variable - 0-to-8ns, 7bit digital delay line. 62ps min resolution. Controlled by linear, single turn front panel control. Fixed - 8ns Switch selectable on front panel (in/out) • Outputs: TTL - 50 ohm line driver, Voh type 2.5v into 50ohm load. Pulse width 1us type (Pulse with is set internally by discrete components). Tr, Tf, <3ns typeAnalog - Tr, Tf, <2ns, Unipolar 0-to-+1v fixed amplitude. Designed to drive DC coupled 50ohm load to ground. Pulse width - 8ns, set internally by 50ohm coax delay line.Sync - 50ohm TTL line driver, 1.3v into 50ohms. Negative edge. • Threshold Adjustment: +/- 200mv applied to input comparator via single turn front panel control. • Input Power: 85-250VAC, 47-63Hz, 50W • Dimensions: 133 H x 430 W x 343 D mm. Rack Mountable. 5.25" x 16.88" x 13.5" • Weight: Net 6.8 Kg, (15lbs) Adjustable Modulator Mounts with Alignment Tool Specifications : Qty -1 • Crystal: 105mm of KD*P • AR Coating: 325nm-to-515nm • Transmission: > 85% • Aperture: 3.1mm • Model 102 Specifications: • Height Adjustment Range: 2.6 inches (6.6cm) o Lowest Center Line 4.15″, 10.5cm o Highest Center Line 6.75″, 17.2cm • Height without Mounting Rings: o Fully Retracted Height 2.30″, 5.8cm o Fully Extended Height 4.90″, 12.4cm o Weight 3.33lbs. • Height with Mounting Rings: (Center of Ring) o Fully Retracted Height 3.90″, 9.9cm o Fully Extended Height 6.50″, 16.5cm o Weight 3.95lbs. • Dimensions: (Overall L x W x H) o Fully Retracted w/o Rings 10″L x 3.6″W x 2.3″H  25.4cm x9.1cm x 5.8cm o Fully Extended w/o Rings 10″L x 3.6″W x4.9″H  25.4cm x9.1cm x12.4cm o Fully Retracted with Rings 10″L x 3.6″W x 6.3″H  25.4cm x9.1cm x 16cm o Fully Extended with Rings 10″L x 3.6″W x 8.9″H  25.4cm x9.1cm x 22.6cm • Alignment Tool Option: o Diameter is 5cm o Aperture 2mm The Government intends to negotiate a sole-source contract with the manufacturer of the required system: Conoptics, Inc. 19 Eagle Rd Danbury, CT 06810 The Government has made a determination that no company other than Conoptics, Inc. has a commercial system that can meet the required specifications listed above: This is a notice of proposed contract action and NOT a request for competitive proposals. However, all responsible sources may submit a capability statement or proposal, which shall be considered by the agency. Responses to this notice must be submitted by the date/time listed on the notice. Any response to this notice must show clear and convincing evidence that competition would be advantageous to the Government in future procurements. Responses received will be evaluated; however a determination by the Government not to compete the proposed procurement based upon responses to this notice is solely within the discretion of the Government. The Government anticipates an award date on or before 21 February 2017 A Sole Source Justification will be attached to the subsequent Notice of Award in accordance with applicable regulation.
 
Web Link
FBO.gov Permalink
(https://www.fbo.gov/spg/USAF/AFMC/AFRLRRS/FA8751-17-Q-0148/listing.html)
 
Place of Performance
Address: Department of the Air Force, Air Force Materiel Command, AFRL – Rome Research Site, AFRL/Information Directorate, Rome, New York, 13441, United States
Zip Code: 13441
 
Record
SN04392406-W 20170208/170206235233-c2c0d0990f62946c2f00226a9232e2c8 (fbodaily.com)
 
Source
FedBizOpps Link to This Notice
(may not be valid after Archive Date)

FSG Index  |  This Issue's Index  |  Today's FBO Daily Index Page |
ECGrid: EDI VAN Interconnect ECGridOS: EDI Web Services Interconnect API Government Data Publications CBDDisk Subscribers
 Privacy Policy  Jenny in Wanderland!  © 1994-2024, Loren Data Corp.