Loren Data's SAM Daily™

FBO DAILY - FEDBIZOPPS ISSUE OF JUNE 15, 2017 FBO #5683
DOCUMENT

65 -- 160 hospital beds/mattresses - Attachment

Notice Date

6/13/2017
 

Notice Type

Attachment
 

NAICS

339999 — All Other Miscellaneous Manufacturing
 

Contracting Office

Department of Veterans Affairs;VISN/18PHX;777 E. Missouri, Suite 300;Phoenix AZ 85014
 

ZIP Code

85014
 

Solicitation Number

VA25817Q0507
 

Response Due

6/23/2017
 

Archive Date

6/28/2017
 

Point of Contact

shawnta Butler Ignacio
 

Small Business Set-Aside

N/A
 

Description

PLEASE NOTE THAT THIS WAS SUPPOSED TO BE ORINALLY POSTED AS A SOLICITATION. TIME WILL BE EXTENDED TO ACCOMMODATE FOR ERROR. ALL QUOTES ALREADY RECEIVED ARE WILL REMAIN ACCEPTABLE. THE BELOW ARE QUESTIONS ASKED AND ANSWERS GIVEN. PLEASE SEE SOW THAT S FOLLOWS FOR UPDATED CHANGES -How many units are needed in the inpatient acute, CLC, spinal cord injury clinic, and excess in the basement? Are any units going into the ICU? RESPONSE: 160 -Is the facility looking to trade in the existing beds? If yes, how many units and what models (list of serial numbers)? RESPONSE: No, no trade in is requested; however vendor removal of the retiring beds is required. -Must have a maximum mattress deck height of 11 inches in the low position (addresses fall risk). Is there a falls reduction guarantee based off the 11 inches height? Or a percentage of falls reduction guarantee on annual basis? RESPONSE: No guarantee in falls reduction is requested - Compatibility with the PVAHCS current Evacusleds. What model of Evacusleds is currently used at the facility? It s our understanding, that the life expectancy of Evacusleds is approx. 10 years. Do you have plans to replace and for what model? RESPONSE: Current model is the standard Evacusled, utilizing the bed mattress for patient evacuation Possible future change to meet facility needs has not been fully evaluated. -Must be able to integrate into existing nurse call system. What nurse call system is the facility currently using? RESPONSE: Westcall's West-Com Novus. Connection required. HOSPITAL MATTRESS: -Must have a 40-degree full body turn capability for assistance with early mobility and prevention of pulmonary complications. Is turn assist required? Is Continual Lateral Rotation Therapy (CLRT) required? RESPONSE: This was added in error as requirement for ICU surfaces ONLY not the General Floor surfaces currently requested -Must have ability to add pump for Low Air Loss option. Is Low Air Loss (LAL) required for all the mattresses? Is a pump/blower required for all the mattresses? RESPONSE: The mattresses requested must have the availability to be converted to Low Air Loss Therapy by additional of an add-on pump Statement of Work Hospital Beds Replacement Phoenix Veterans Administration Health Care Services 650 E. Indian School Road Phoenix, AZ 85012 Equipment Request #: 644-470-17-00001 POC: James Monigold ext 5550 CC: Tiffany Jennings, AO/PCS ext 6158 1. Statement of Work 1.1 Introduction to Required Specifications Purpose: The purpose of this Statement of Work (SOW) is to outline the technical specifications and responsibilities of the awarded Vendor, in relation to the provision, integration, and implementation of a complete hospital bed replacement in the inpatient acute, CLC, spinal cord injury clinic, and excess in the basement at the Phoenix VA Health Care System. The Phoenix VA shall require removal of the existing hospital beds in the aforementioned locations, and installation and implementation of the new replacement beds. The Vendor shall provide all necessary tools, equipment/hardware, installation, maintenance, warranty, and training in accordance with this SOW. Primary Goals: The facility s primary goals are to achieve standardization, enhancement of patient safety, standardized/improvement safety protocols, enhanced patient data reports and record capabilities, reduction in labor, and overall improvement of patient care. In addition, these beds will replace existing beds that are at end of life, expand the capacity and capability of current clinical workflow, improve patient safety and handling, increased patient satisfaction, and provide consistent and reliable end user experience at point of care. Equipment: All equipment shall be new, state of the art, and not recertified nor refurbished. Industry Standards: Unless otherwise stated, all equipment shall be held to current industry standards for such equipment as present within the current market for hospital beds, supplies, related services, and the most recent International Standards set by the IEC (IEC 60601-2-52). Definitions Hospital Bed: A bed specially designed for hospitalized patients or others in need of some form of health care. These beds have special features both for the comfort and well-being of the patient and for the convenience of health care workers. Common features include adjustable height for the entire bed, the head, and the feet, adjustable side rails, and electronic buttons to operate both the bed and other nearby electronic devices. These beds are for medical surgical care appropriate for the use in long term and acute areas. Hospital Mattress: A mattress specially designed for hospitalized patients or others in need of some form of health care. These mattresses have special features both for the comfort and well-being of the patient and for the convenience of health care workers. Common features include a therapeutic surface, pressure redistribution, shear management, moisture management, deep zipper flap, waterproof seams, delamination protection, fits bed frames 80-84, has nonskid bottom and or straps to secure to bed frame, ability to support 500 pound weight, ability to use for High risk up to Stage IV pressure ulcers, five year or greater warranty, and full or prorated replacement availability. These mattresses are for medical surgical care appropriate for the use in long term and acute areas. Hardware/Software Hospital Bed (qty:160) The hospital bed shall meet or exceed all technical specifications listed below: Must support minimum weight capacity of 500 lbs. Must have maximum bed frame weight of 500 pounds Must have a battery back-up with battery power indicator. Must have a power status indicator, indicating power source (AC Wall power), and battery only. Must have a battery back-up with battery power indicator. Must have 4 casters with central brake. Must have dual castors for ease of transport. Must have corner bumpers to protect bed frame and facility walls/doorways Must have a flat mattress deck for standard mattress compatibility, and compatibility with the PVAHCS current Evacusleds. Must have a maximum mattress deck height of 11 in the low position (addresses fall risk). Must have a siderail height of 16 for maximum patient safety (from mattress deck to the top of the rail). Must have a minimum clearance height of 6 (below the bed) to allow access for under-bed tables and lift equipment Must not have horizontal or lateral movement of bed mattress deck. Must have audible bed exit alarms and foot of bed visual sidelight indicators. The sidelight indicators must be color coded for bed alarm settings or siderail configuration changes. The bed exit alarm must have minimum 3 sensitivity levels i.e. out of bed, perimeter of bed, and patient sitting. The bed exit alarm must have minimum of 3 volume status (low, medium, high). Must have capability of an electronic log of all bed exit related events to include a minimum of 5 days. Must have an automatic bed exit alarm reset function for fall prevention, in the event that a staff member forgets to reset. Must have siderails with inner controls for the patient, and outer controls for the staff. Must have footboard with staff controls on an angled surface for ergonomics with an LED display, backlit for ease of reading. Both the siderails and footboard controls must have integrated lockout capability. Must have frame mounted back up controls to prevent loss of bed control in the event footboard removal. Must meet latest norm IEC 60601-2-52 and 60601-2-38. Must have patient remote and removable control with minimum of 4 functions (head up, head down, legs up, and legs down). Must have emergency CPR functions (automatic & manual) with no reset required. Must be able to integrate into existing nurse call system. Must have under bed lighting with minimum two light strength settings. Must have capability to weigh patients to +/- 1% standard deviation of error. Must have steering capability setting for transport. Must operate with standard 120 v. wall power outlet. Must have secured O2 E tank pivoting holder for safety and to allow fitting into elevators, with ability to secure in more than one bed frame corner. Minimum of (2) 120v. auxiliary electrical outlets on frame. Must have electronic positioning ability for both Trendelenburg and reverse Trendelenburg, without hitting headboard against wall (no bed location movement requirement) to prevent wall damage. Must have electronic readouts for bed angles located on footboard. Must have non-laser under bed obstruction sensor to prevent false detection. Must have custom fitted trapeze specifically manufactured for this bed (20% of beds). Bed width must not exceed 41, in order to fit through patient room doorways. Bed length must not exceed 91 (92.5 inches including frame bumpers) in order to fit in all hospital elevators. Must have frame corner/end bumpers for prevention of wall damage. Must have one touch electronic cardiac chair position (efficiency, consistency, ease of use, staff, and patient satisfaction). Must have 30 ° back rest indicator on siderail. Must have minimum of 2 drainage bag holders that are easily accessible on outside perimeter of bed frame (one on each side). Must have minimum of 4 restraint secure points (2 on each side). Must have integrated IV pump holder. Must have ability to secure electrical cord on outside headboard area. Must accept standard flat (not contoured) 35 x 84 hospital mattresses. Must have 4 siderails, 2 upper and 2 lower, with one hand release Must have seamless smooth plastic siderails and food/head boards (no metal, wood or laminate) with no openings for ease of cleaning, aesthetics and infection control. Must be fully electronic for multi-positional, multi-height capability, with articulating back and knee gatch. Siderails must have vertical up/down articulation (not swing outward), with color or light indicator for visual position locking indication/verification. Must have brake status indicator (locked/unlocked). Must have removable deck cover, footboard and headboard for cleaning/replacement. Life expectancy of beds must meet or exceed 10 years. Upper siderail must not extend past the articulation section between the head and middle bed sections when in the rail up position (allows for open area for patient to side enter/exit without a necessary secondary boosting up in bed) Bed frame must have integrated no tools required deck frame and deck plate extension lengthening capability beyond 84 inches to a minimum of 90 inches to accommodate the taller patient. (integrated decking/plate extension to minimize time requirement to shorten bed for fitting into the elevator during emergency transport) Must be compatible with existing facility Evacusleds for emergency evacuation requiring minimal staff lifting over siderails or mattress securing brackets and allow unencumbered Evacusled wheel movement over bed mattress deck with bed frame in extended (beyond 84 inches in length) or un-extended position. Warranty: The Vendor shall provide a minimum warranty of no less than five (5) years for parts and labor for the beds. This warranty will cover the entirety of the bed and all its components and accessories. Hospital Mattress(qty:160) The hospital bed shall meet or exceed all technical specifications listed below: Must support minimum weight capacity of 500 lbs. Must have a therapeutic surface to assist in management of pressure, shear, and microclimate for the patient. Must have ability to redistribute pressure through buckling and absorbing patient weight and allow immersion and envelopment to maintain comfort in all positions on the mattress. Must have a breathable cover that wicks away moisture, equalizes pressure redistribution while balancing the microclimate of the patient s skin Must not conduct heat Must have compatibility with the PVAHCS current Evacusleds. Must have a maximum mattress height of 6 for easy ingress and egress of patients. Must allow for a side rail height of 16 for maximum patient safety (from mattress deck to the top of the rail). Must have a nonskid bottom surface or straps to secure to bed frame. Must fit selected hospital bed frame of 84x35 (LXW) Must have firm edges to prevent collapsing for sitting on side of bed and support weight during ingress and egress. Must have delamination protection. Must waterproof seams Must have a deep zipper flap Must be latex free Must have a 40 degree full body turn capability for assistance with early mobility and prevention of pulmonary complications Added in error NOT a requirement for acute care mattresses Prefer the availability of sensor technology for automatic adjustment of pressure for patient weight, height, position changes, and bed frame articulation changes Must meet US flammability standards: 16CFR1632, 16CFR1633, CAL TB129, Boston BFD IX-11. Must have bleach tolerant cover for cleaning Must have ability to add pump for Low Air Loss option (transition) Life expectancy of mattresses must meet or exceed 5 years with availability of full or prorated replacement prior to expiration of warranty. Warranty: The Vendor shall provide a minimum warranty of five (5) years for parts and labor for the mattresses. This warranty will cover the entirety of the mattress and all its components and accessories. Installation Considerations Vendor shall provide all materials, labor, and travel needed for installation of the mattresses. Vendor will work during normal business hours or as directed by the facility upon award. Services shall include removal and disposal of all mattresses needing replacement. Vendor shall comply with all VA mandated and local permitted/safety requirements User and Service Manuals: The Vendor shall provide to each station at no charge, two (2) completed and unabridged printed copies and one (1) electronic version (CD) of operator manuals, service manuals, electronics schematics, troubleshooting guides, and diagnostic software and tools, and parts lists for each piece of equipment purchased to the Biomedical Engineering department with delivery of equipment. Additionally any upgrades to these documents shall be provided by the Vendor free of charge. These manuals shall include all components and subassemblies, including those not manufacturer by the Vendor. These manuals and documentation shall be identical to the ones supplied to the manufacturer s service representatives, and shall contain the diagnostics codes, commands, and passwords utilized in maintenance, repair, and calibration of the equipment and provided for the life of the system at no additional cost. Licensing Software updates: The Vendor shall provide at no charge, for the lifetime of the device, all routine software updates. All applications software licenses are included in the purchase of the equipment and shall not require a renewal charge for the period of time the equipment is in the use in the facility. Clinical Training: The Vendor shall provide a training program that is coordinated with and timely to the equipment installation, sufficient to the size and scope of the facility s services and minimally equivalent to the terms and conditions for training defined in the Vendor s FSS Contract. Training shall include initial setup and user-training; onsite training for go-live support, and follow-up training as requested. Training will include ongoing customer support after the implementation of the equipment. Biomedical Engineering Training: The Vendor shall provide training of the Biomedical Equipment Support Specialists (Hereafter referred as BESS) during initial setup and operations of the equipment, as well as follow-up training during everyday operation. The Vendor shall provide 24/7 technical customer support service for the duration of the equipment at the facility. The on-site training, following installation completion, shall include product nomenclature, printed circuit board assembly and subassembly identification and location, interpretation and usage of built-in system diagnostics, and the use of the troubleshooting manual. The Vendor shall also provide service seminars at the Vendor s facility tuition-free while the hospital owns the equipment. Support/Maintenance Agreements: Vendor shall provide service/maintenance agreement for 8am-6pm PST coverage and provide 24/7 technical and clinical phone support. Patient Information Privacy and Protection In accordance with Appendix A, Handbook 6500.6 Checklist blocks 6, the C&A requirements do not apply to this requirement, and a Security Accreditation Package is not required. In reference to no. 7 there is no information to be protected. The equipment does not store any PHI/PII/PI, nor are there any hard drives/storage devices to service or remove. The period of performance will be 120 days after receipt of award. 2.3 Delivery and Shipping Information: The vendor shall provide the following for shipment and delivery of equipment: All items and services shall be shipped or contact to the following location: Attention: Susan Wyatt Theresa Nussbaumer 650 E. Indian School Road Phoenix, AZ 85012-1892
 

Web Link

FBO.gov Permalink
(https://www.fbo.gov/spg/VA/PhVAMC/HMC/VA25817Q0507/listing.html)
 

Document(s)

Attachment
 

File Name: VA258-17-Q-0507 VA258-17-Q-0507_2.docx (https://www.vendorportal.ecms.va.gov/FBODocumentServer/DocumentServer.aspx?DocumentId=3578062&FileName=VA258-17-Q-0507-001.docx)

Link: https://www.vendorportal.ecms.va.gov/FBODocumentServer/DocumentServer.aspx?DocumentId=3578062&FileName=VA258-17-Q-0507-001.docx

 

Note: If links are broken, refer to Point of Contact above or contact the FBO Help Desk at 877-472-3779.
 

Record

SN04542809-W 20170615/170613234944-6421720c0b50ffeb3b3fc8e96ba92b2f (fbodaily.com)
 

Source

FedBizOpps Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's FBO Daily Index Page |