SOURCES SOUGHT
J -- TARDEC CSI Lab Maintenance and Emergency Repairs - RFI Attachments
- Notice Date
- 10/17/2017
- Notice Type
- Sources Sought
- NAICS
- 811310
— Commercial and Industrial Machinery and Equipment (except Automotive and Electronic) Repair and Maintenance
- Contracting Office
- Department of the Army, Army Contracting Command, ACC - WRN (W56HZV)(DTA), 6501 EAST 11 MILE ROAD, Warren, Michigan, 48397-5000, United States
- ZIP Code
- 48397-5000
- Solicitation Number
- W56HZV-18-T-L002
- Archive Date
- 11/17/2017
- Point of Contact
- Jerry S. Carter, Phone: 5862825502
- E-Mail Address
-
jerry.s.carter7.civ@mail.mil
(jerry.s.carter7.civ@mail.mil)
- Small Business Set-Aside
- N/A
- Description
- Summary of the Requirement RFI Questions Summary of the Requirement Machine Manufacturer certified technician for preventive maintenance and emergency repairs are required for the following machinery: Manufacturer Model # Serial # LNS (DY30) QLS80 S2 27011901 LNS (SL-20) Q.L. SERVO S3 304090 Time Saver 4121-25-04 2392-07 Time Saver 3/5/4111 2348-08 Bystronic BYSTAR 3015 989.0.0759 Flow 020429-1 397250 Flow 6 x 12 30810838 Omax 120X L511508 Omax 60120 H511717 Haas VF-6SS 1076453 Haas SL-10T 66102 Haas TM-2 1050642 Haas TM-3P 1076113 Haas DS-30SSY 3090742 Haas TL-2 3079779 Haas SL-20LB 3080472 Haas (SL-10) Serv Bar 300 100787 Haas VS-3 2054253 Preventive Maintenance Requirements by Product Technology: Group 1: HAAS Mills and Lathes Perform the following annual maintenance / checks on each machine. An HAAS factory trained technician is required to perform this service: • Mechanical System Check machine level Verify spindle sweep • Check gear shift operation* • Check spindle lube and air blast • Check spindle orientation alignment • Check shot pin operation* • Change gearbox oil • Check backlash in X, Y, and Z-axis • Inspect drive belts • Inspect and adjust tool changer system • Inspect spindle taper condition • Inspect way covers & wipers • Check draw bar height • Inspect rigid tap encoder operation* • Check tool change operation • Clean/lubricate tool changer • Inspect counterbalance system • Inspect lines, hoses and cables • Way Lube System • Clean filters • Inspect lines and fittings • Check operation • Verify lube/pump operation • Coolant System: Remove/check pump and motor, (Inspect or Clean coolant tank and replace coolant as needed) • Air System: Replace filters, Check pressure/adjust regulator, Inspect system for leaks • Electrical System: Check voltages, Clean electrical cabinet, Inspect connections/terminals and grounds • Inspect or replace tool change relays • Replace or clean fan filter • Check limit switches/safety locks • Inspect motor brushes, clean & remove brush dust • Lathe Only: Verify turret/spindle alignment • Manual Machines: Change oil, filter and belts, Lubricate system and clean as necessary to be qualified as working property. • Adjust Gibs • Check level and alignment • Inspect general machine function Items ending with an "*" are services performed if applicable. Group2: OMAX Water Jets Perform the following annual maintenance / checks on each machine. An OMAX factory trained technician is required to perform this service: • Inspect and grease ball-screws, pulleys and fittings. • Replace all belts. • Replace all filters. • Rebuild and upgrade (when applicable) the OMAX pump, includes one Seal Rebuild Kit and • Check Valve Repair Kit, plus inspection of the bearings and plungers. • Calibrate the V pump. • Rebuild all swivels using Swivel Rebuild kits • Replace all High Pressure Tubing, Collars, Collets, Gland Nuts and Fittings. • Install the latest revision of OMAX Software. Group 3: FLOW Water Jets Perform the following annual maintenance / checks on each machine. A FLOW factory trained technician is required to perform this service: • Inspect and grease ball-screws, traction drives, pulleys and fittings. • Grease all lubrication points • Replace all belts. • Replace all filters. • Rebuild and upgrade (when applicable) the Flow pump, includes one Seal Rebuild Kit and • Check Valve Repair Kit, plus inspection of the bearings and plungers. • Calibrate the pump. • Rebuild all swivels using Swivel Rebuild kits • Inspect all High Pressure Tubing, Collars, Collets, Gland Nuts and Fittings. Group 4 - Timesaver Deburring Machines Perform the following annual maintenance / checks on each machine. A Timesaver factory trained technician is required to perform this service: • REPLACE CONVEYOR BELT As Needed Part# C30834300 (Qty 1) • REPLACE WEAR BARS ON BED as needed Part# B30837700 (Qty 2) • TRACK CONVEYOR BELT as needed • CLEAN VACUUM HOLES/CHAMBERS IN BED • TENSION AND LUBE BED LIFT CHAIN Lube: Chain Lube/Lightweight Oil • INSPECT/REPLACE GUIDE ROLLERS As Needed Part#A30188201 (Qty 2) • CHANGE GEARBOX LUBE (LIFT) Change Lube every 2,500 Hours Lube: Gear Oil • CHANGE GEARBOX LUBE (FEED) Check Level and Change Lube every 2,500 Hours Lube: Gear Oil • Check LUBE BED JACKS Lube: Multi-Purpose Grease (Grease Zerks) Fill Oil Pot (If Equipped) • LUBE ALL BEARINGS Lube: Multi-Purpose Grease • CAROUSEL: TENSION/LUBE LIFT CHAIN Check Lube: Chain Lube/Lightweight Oil • CAROUSEL: LUBE JACKS Check Lube: Lightweight Oil • CAROUSEL: TENSION/LUBE ROTATIONAL CHAIN Check Lube: Chain Lube/Lightweight Oil • CAROUSEL: CHECK ALIGNMENT as needed • CAROUSEL: CHANGE LIFT GEARBOX LUBE (IF SERVICEABLE) Check Gear Oil level as needed; Change Lube every 2,500 Hours • CAROUSEL: CHECK IDLER SPROCKET BEARINGS Perform while lubing chain as needed • CAROUSEL: Replace the following parts as necessary: a) Jack Assy (#30753400) b) Chain • SPINDLE: CHECK GEAR WEAR (REPLACE AS NECESSARY) Perform while lubing gears • SPINDLE: LUBE GEARS as needed Lube: Lithium Grease as needed • SPINDLE: LOCTITE BOLTS using Blue/Medium Hold that hold gear to shaft as needed Perform during first service/lube service • SPINDLE: Replace bearings annually Part# P80000-66-30-16 (Generic NTN#6206 Sealed Bearings) - Qty 16 Immediately order the following maintenance parts to keep on hand due in the TARDEC shop due to lead times: A) Spindle Gear (#30755900SG) - Qty 10 B) Bearings (#P80000-66-30-16; NTN#6206) - Qty 20 C) End Nut (RH#B30849000; LH#B30849001) - Qty 5 D) Hex Shaft (RH#30824900; LH#30824901) - Qty 5 [ E) Lock Nut and Washer (New Style Only) F) Part# B30838300 - Qty 8 G) Part# P80000-66-30-16 H) Part# P83130-0A-019 - Qty 1 I) Part# B30838300 - Qty 8 • CLEAN DUST COLLECTION PIPES • INSPECT ABRASIVES (REPLACE AS NEEDED) Part# B30838300 • CLEAN VACUUM HOSES • CLEAN/REPLACE VACUUM BLOWER DUST BAG (IF EQUIPPED) Interval: Shake Out (Daily); Clean (Monthly); Replace (As Needed) Recommend replacement of Part# P83130-0A-019 LUBE VACUUM BLOWER MOTOR • CHECK ALL SAFETY OPERATIONS • CHECK PINCHROLLS FOR OPERATION/WEAR/ALIGNMENT Group 5: Bystronic Laser Provide the 5-Star Extended Service plan through Bystronic for the required annual maintenance / checks on the Bystronic laser. A Bystronic factory trained technician is required to perform this service: • Unlimited Technical Phone Support from 7:30 - 18:00 CT M-F; • Unlimited Bysoft Technical Phone Support from 7:30 - 18:00 CT M-F; • Unlimited Applications Technical Phone Support from 7:30 - 18:00 ET M-F; • Bysoft Update to the next whole release number; does not apply to Bysoft 7 or later • One (1 ) Performance Inspection; • Twelve (12) Emergency Repair calls; • Warranty coverage on parts which includes freight (excluding consumables); • Laser Machine Network Support; Group 6: Emergency Service Factory trained technicians are required to perform this service
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/notices/abea058de054ea9a5d625e8e115482d5)
- Place of Performance
- Address: Warren, Michigan, 48397, United States
- Zip Code: 48397
- Zip Code: 48397
- Record
- SN04715757-W 20171019/171017231250-abea058de054ea9a5d625e8e115482d5 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |