MODIFICATION
14 -- AFT Fairing Supplies
- Notice Date
- 7/25/2018
- Notice Type
- Modification
- NAICS
- 332312
— Fabricated Structural Metal Manufacturing
- Contracting Office
- 1 OVERCASH AVE CHAMBERSBURG PA 17201-4150
- ZIP Code
- 17201-4150
- Solicitation Number
- W25G1R811001QY
- Response Due
- 8/15/2018
- Point of Contact
- Kevin Duffy, Phone 7172678938
- E-Mail Address
-
kevin.a.duffy4.civ@mail.mil
- Small Business Set-Aside
- Total Small Business
- Description
- Amendment #3 W25G1R811001QY Questions & Answers AFT Fairing Supplies Question #1: We need a BOM to identify components and what their material type is? Answer #1: 16S307 PL.pdf is the Parts list, provided. Question #2: We need Spec FPS-3017, FPS-3018 to identify approved cutting and bending processes? Answer #2: FPS-3017, provided. Question #3: Need Spec FPS-1003 that applies to the sealing Answer #3: 16S307 PL.pdf is the Parts list, provided. Question # 4: Need to know a supplier that can apply the urethane primer and paint? Answer #4: The supply chain is the responsibility of the Offeror, however application and painting must conform to the drawings. Question #5: What are the riveting requirements? Answer #5: MIL-STD-40007.pdf is the riveting requirements, provided. Question #6: Need to know where to purchase the QQ-A-250/4 T62 material from? Answer #6: The supply chain is the responsibility of the Offeror, however the material must conform to the drawing requirement. Question #7: Need an approved heat treat supplier. Answer #7: The supply chain is the responsibility of the Offeror, however heat treatment must conform to the drawing requirement. Question #8: Do we have the NDTS 1101 FPI spec? Are we certified to inspect in house? Answer #8: If the material that is purchased is certified to the spec on the drawing, no additional certification of material is needed. NDTS1500 and NDTS1101 are the specs and are provided. Question #9: On sheet 1 above the title block it states to see a separate parts list. Can you obtain that? Answer #9: Please refer to Answer #1-Provided. Question #10: We assumed this will be aluminum. However, it is not specifically called out on the drawing what grade or type. I believe this is because it is an assembly drawing and not component part drawings. Answer #10: According to parts list, QQ-A-250/4 T62 aluminum is the required material. Question #11: On sheet 2 there are different dash numbers.... -1, -3, and -5 assembly. Do you know which one to consider? Answer #11: There are 3 variants of the aft fairing, all three are on this same drawing, 16S307-5 is the variant required. Question #12: There are also bubbles with dash numbers in them that we believe lead to details. Some of these details are not included. Perhaps they are on the component part drawings. Answer #12: The dash numbers are referring to which variation of the aft fairing this is for (-1, -3, -5). As noted in answer #11, 5 is the variant required. Question #13: Zone D3 there is a radius called out that has no dimension. Answer #13: D3 is the zone location on the physical drawing by looking on the outside edge, the radius is listed in zone D3; due to room, they moved the radius below the arrows for that radius. NOTE: THIS NOTICE WAS NOT POSTED TO FEDBIZOPPS ON THE DATE INDICATED IN THE NOTICE ITSELF (25-JUL-2018); HOWEVER, IT DID APPEAR IN THE FEDBIZOPPS FTP FEED ON THIS DATE. PLEASE CONTACT 877-472-3779 or fbo.support@gsa.gov REGARDING THIS ISSUE.
- Web Link
-
Link To Document
(https://www.fbo.gov/notices/cad858307f59211208d1ba9f5963b5ce)
- Place of Performance
- Address: One Overcash Avenue Chambersburg, PA
- Zip Code: 17201
- Country: US
- Zip Code: 17201
- Record
- SN05006921-F 20180727/180725230843 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |