SAMDaily.us | PRESOL | 84 | Combat Helmets

SAMDAILY.US - ISSUE OF FEBRUARY 23, 2020 SAM #6660
SOLICITATION NOTICE

84 -- Combat Helmets

Notice Date: 2/21/2020 7:40:37 AM
Notice Type: Combined Synopsis/Solicitation
NAICS: 423850 — Service Establishment Equipment and Supplies Merchant Wholesalers
Contracting Office: W6QM MICC-FT DRUM FORT DRUM NY 13602-5220 USA
ZIP Code: 13602-5220
Solicitation Number: PCDKWD20191118
Response Due: 2/21/2020 8:59:59 PM
Archive Date: 05/18/2020
Point of Contact: Name: Marketplace Support, Title: Marketplace Support, Phone: 1.877.933.3243, Fax: 703.422.7822, Email: MarketplaceSupport@unisonglobal.com;
E-Mail Address: marketplacesupport@unisonglobal.com
(marketplacesupport@unisonglobal.com)
Small Business Set-Aside: SBA Total Small Business Set-Aside (FAR 19.5)
Awardee: null
Description: This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice. The solicitation number is PCDKWD20191118 and is issued as a Request for Quote (RFQ), unless otherwise indicated herein. The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 22020-01. The associated North American Industrial Classification System (NAICS) code for this procurement is 423850 with a small business size standard of 100.00 employees. This requirement is a Small Business Set-Aside and only qualified offerors may submit bids. The solicitation pricing on www.UnisonMarketplace.com will start on the date this solicitation is posted, and, unless otherwise displayed at www.UnisonMarketplace.com, will end on: 2019-11-20 13:30:00.0 Eastern Time. This time supersedes the Offers Due Time listed above. FOB Destination shall be Pueblo, CO 81006 The MICC End User requires the following items, Brand Name or Equal, to the following: LI 001: Viper P4 UHC 1NVG TAN 499 SM MSS must contain Tan High Cut Ballistic Shell, MSS Retention System and Suspension System. High cut helmet: a size Medium helmet shall have a minimum protective surface area of at least 144in2 (929cm2). 4-point retention system with chin cup and adjustable straps. The straps shall have no loose ends. Must also contain the following attachments: Front Mount shall be available in 4 sizes compatible with helmet sizing. Shall not require any modification or additional drill holes. A size Medium Front Mount (configured for PVS-7 or PVS-14) shall weigh no more than 85g. Right and Left Side Rails - shall consist of left and right rails in 4 sizes to fit small through extra-large helmets. Must lock with Front Mount to ensure no rotational movement. Multiple entry points accept widely used rail bases, such as swivel clips, picatinny and winged rail bases. Design shall allow for easy, one-handed attachment of widely used rail bases and accommodates O2 clips for use with oxygen masks. Size Medium rails shall weigh no more than 85g. Ballistic Visor - The ballistic visor shall attach to the front mount at the standard NVD interface. The ballistic Visor should be available in a Standard or Max Version. The visor must have three positions and have the capability to be in an open, vented or closed position. Operation of the visor mechanism shall be able to be utilized with one hand. The visor shall be able to be donned and doffed using one hand. The visor assembly shall weigh no more than: Standard Version: 280g, Max Version: 335g. The visor system must be able to be used with ballistic eyewear and goggles. The Standard visor system must be able to be worn with an M50 CBRN mask. The visor must offer a removable gasket seal. Ballistic Performance, Fragmentation protection: 1.1g FSP V50 > 235 m/s, tested in accordance with STANAG 2920 Ed2. Optical standards: The visor must pass MCEPS abrasion requirements. Must have replaceable visor lens. The Fragmentation visor must engage with Revision�s Standalone or Interlocking rails The Visor must have three positions. The Visor must be size specific for each sized helmet � small, medium, large, X-large. The visor shall be 6mm think and 15.5 mm cm, Ballistic Performance .17 grain, .22 cal V50 = 350m/s, Blunt impact is greater than 45 J. Ballistic Mandible Guard - The ballistic mandible shall attach to the front mount on the left and right side with slotted guides that can pivot open and closed. Shall allow for one handed operation for quick removal of the mandible. The mandible guard must be doffed and donned without removing the helmet. Ballistic Performance: Fragmentation protection: 1.1g FSP V50 > 670 m/s, tested in accordance with STANAG 2920 Ed2. The mandible guard must resist penetration of a 9mm FMJ in accordance with NIJ 0101.04 at 427 m/s. While installed, the mandible guard must be able to tilt downwards in two positions to enable use with large NVGs and to facilitate hydration. The guard must be able to be brought back to the original position with a quick, hands-free operation. 4-0555-5045, 15, EA; LI 002: Viper P4 UHC 1NVG TAN 499 MD MSS must contain Tan High Cut Ballistic Shell, MSS Retention System and Suspension System. High cut helmet: a size Medium helmet shall have a minimum protective surface area of at least 144in2 (929cm2). 4-point retention system with chin cup and adjustable straps. The straps shall have no loose ends. Must also contain the following attachments: Front Mount shall be available in 4 sizes compatible with helmet sizing. Shall not require any modification or additional drill holes. A size Medium Front Mount (configured for PVS-7 or PVS-14) shall weigh no more than 85g. Right and Left Side Rails - shall consist of left and right rails in 4 sizes to fit small through extra-large helmets. Must lock with Front Mount to ensure no rotational movement. Multiple entry points accept widely used rail bases, such as swivel clips, picatinny and winged rail bases. Design shall allow for easy, one-handed attachment of widely used rail bases and accommodates O2 clips for use with oxygen masks. Size Medium rails shall weigh no more than 85g. Ballistic Visor - The ballistic visor shall attach to the front mount at the standard NVD interface. The ballistic Visor should be available in a Standard or Max Version. The visor must have three positions and have the capability to be in an open, vented or closed position. Operation of the visor mechanism shall be able to be utilized with one hand. The visor shall be able to be donned and doffed using one hand. The visor assembly shall weigh no more than: Standard Version: 280g, Max Version: 335g. The visor system must be able to be used with ballistic eyewear and goggles. The Standard visor system must be able to be worn with an M50 CBRN mask. The visor must offer a removable gasket seal. Ballistic Performance, Fragmentation protection: 1.1g FSP V50 > 235 m/s, tested in accordance with STANAG 2920 Ed2. Optical standards: The visor must pass MCEPS abrasion requirements. Must have replaceable visor lens. The Fragmentation visor must engage with Revision�s Standalone or Interlocking rails The Visor must have three positions. The Visor must be size specific for each sized helmet � small, medium, large, X-large. The visor shall be 6mm think and 15.5 mm cm, Ballistic Performance .17 grain, .22 cal V50 = 350m/s, Blunt impact is greater than 45 J. Ballistic Mandible Guard - The ballistic mandible shall attach to the front mount on the left and right side with slotted guides that can pivot open and closed. Shall allow for one handed operation for quick removal of the mandible. The mandible guard must be doffed and donned without removing the helmet. Ballistic Performance: Fragmentation protection: 1.1g FSP V50 > 670 m/s, tested in accordance with STANAG 2920 Ed2. The mandible guard must resist penetration of a 9mm FMJ in accordance with NIJ 0101.04 at 427 m/s. While installed, the mandible guard must be able to tilt downwards in two positions to enable use with large NVGs and to facilitate hydration. The guard must be able to be brought back to the original position with a quick, hands-free operation. 4-0555-5050, 50, EA; LI 003: Viper P4 UHC 1NVG TAN 499 LG MSS must contain Tan High Cut Ballistic Shell, MSS Retention System and Suspension System. High cut helmet: a size Medium helmet shall have a minimum protective surface area of at least 144in2 (929cm2). 4-point retention system with chin cup and adjustable straps. The straps shall have no loose ends. Must also contain the following attachments: Front Mount shall be available in 4 sizes compatible with helmet sizing. Shall not require any modification or additional drill holes. A size Medium Front Mount (configured for PVS-7 or PVS-14) shall weigh no more than 85g. Right and Left Side Rails - shall consist of left and right rails in 4 sizes to fit small through extra-large helmets. Must lock with Front Mount to ensure no rotational movement. Multiple entry points accept widely used rail bases, such as swivel clips, picatinny and winged rail bases. Design shall allow for easy, one-handed attachment of widely used rail bases and accommodates O2 clips for use with oxygen masks. Size Medium rails shall weigh no more than 85g. Ballistic Visor - The ballistic visor shall attach to the front mount at the standard NVD interface. The ballistic Visor should be available in a Standard or Max Version. The visor must have three positions and have the capability to be in an open, vented or closed position. Operation of the visor mechanism shall be able to be utilized with one hand. The visor shall be able to be donned and doffed using one hand. The visor assembly shall weigh no more than: Standard Version: 280g, Max Version: 335g. The visor system must be able to be used with ballistic eyewear and goggles. The Standard visor system must be able to be worn with an M50 CBRN mask. The visor must offer a removable gasket seal. Ballistic Performance, Fragmentation protection: 1.1g FSP V50 > 235 m/s, tested in accordance with STANAG 2920 Ed2. Optical standards: The visor must pass MCEPS abrasion requirements. Must have replaceable visor lens. The Fragmentation visor must engage with Revision�s Standalone or Interlocking rails The Visor must have three positions. The Visor must be size specific for each sized helmet � small, medium, large, X-large. The visor shall be 6mm think and 15.5 mm cm, Ballistic Performance .17 grain, .22 cal V50 = 350m/s, Blunt impact is greater than 45 J. Ballistic Mandible Guard - The ballistic mandible shall attach to the front mount on the left and right side with slotted guides that can pivot open and closed. Shall allow for one handed operation for quick removal of the mandible. The mandible guard must be doffed and donned without removing the helmet. Ballistic Performance: Fragmentation protection: 1.1g FSP V50 > 670 m/s, tested in accordance with STANAG 2920 Ed2. The mandible guard must resist penetration of a 9mm FMJ in accordance with NIJ 0101.04 at 427 m/s. While installed, the mandible guard must be able to tilt downwards in two positions to enable use with large NVGs and to facilitate hydration. The guard must be able to be brought back to the original position with a quick, hands-free operation. 4-0555-5055, 50, EA; LI 004: Viper P4 UHC 1NVG TAN 499 XL MSS must contain Tan High Cut Ballistic Shell, MSS Retention System and Suspension System. High cut helmet: a size Medium helmet shall have a minimum protective surface area of at least 144in2 (929cm2). 4-point retention system with chin cup and adjustable straps. The straps shall have no loose ends. Must also contain the following attachments: Front Mount shall be available in 4 sizes compatible with helmet sizing. Shall not require any modification or additional drill holes. A size Medium Front Mount (configured for PVS-7 or PVS-14) shall weigh no more than 85g. Right and Left Side Rails - shall consist of left and right rails in 4 sizes to fit small through extra-large helmets. Must lock with Front Mount to ensure no rotational movement. Multiple entry points accept widely used rail bases, such as swivel clips, picatinny and winged rail bases. Design shall allow for easy, one-handed attachment of widely used rail bases and accommodates O2 clips for use with oxygen masks. Size Medium rails shall weigh no more than 85g. Ballistic Visor - The ballistic visor shall attach to the front mount at the standard NVD interface. The ballistic Visor should be available in a Standard or Max Version. The visor must have three positions and have the capability to be in an open, vented or closed position. Operation of the visor mechanism shall be able to be utilized with one hand. The visor shall be able to be donned and doffed using one hand. The visor assembly shall weigh no more than: Standard Version: 280g, Max Version: 335g. The visor system must be able to be used with ballistic eyewear and goggles. The Standard visor system must be able to be worn with an M50 CBRN mask. The visor must offer a removable gasket seal. Ballistic Performance, Fragmentation protection: 1.1g FSP V50 > 235 m/s, tested in accordance with STANAG 2920 Ed2. Optical standards: The visor must pass MCEPS abrasion requirements. Must have replaceable visor lens. The Fragmentation visor must engage with Revision�s Standalone or Interlocking rails The Visor must have three positions. The Visor must be size specific for each sized helmet � small, medium, large, X-large. The visor shall be 6mm think and 15.5 mm cm, Ballistic Performance .17 grain, .22 cal V50 = 350m/s, Blunt impact is greater than 45 J. Ballistic Mandible Guard - The ballistic mandible shall attach to the front mount on the left and right side with slotted guides that can pivot open and closed. Shall allow for one handed operation for quick removal of the mandible. The mandible guard must be doffed and donned without removing the helmet. Ballistic Performance: Fragmentation protection: 1.1g FSP V50 > 670 m/s, tested in accordance with STANAG 2920 Ed2. The mandible guard must resist penetration of a 9mm FMJ in accordance with NIJ 0101.04 at 427 m/s. While installed, the mandible guard must be able to tilt downwards in two positions to enable use with large NVGs and to facilitate hydration. The guard must be able to be brought back to the original position with a quick, hands-free operation. 4-0555-5060, 10, EA; LI 005: Caiman Ballistic Black XL MSS must contain Black High Cut Ballistic Shell, MSS Retention System and Suspension System. High cut helmet: a size Medium helmet shall have a minimum protective surface area of at least 144in2 (929cm2). 4-point retention system with chin cup and adjustable straps. The straps shall have no loose ends. Must also contain the following attachments: Front Mount shall be available in 4 sizes compatible with helmet sizing. Shall not require any modification or additional drill holes. A size Medium Front Mount (configured for PVS-7 or PVS-14) shall weigh no more than 85g. Right and Left Side Rails - shall consist of left and right rails in 4 sizes to fit small through extra-large helmets. Must lock with Front Mount to ensure no rotational movement. Multiple entry points accept widely used rail bases, such as swivel clips, picatinny and winged rail bases. Design shall allow for easy, one-handed attachment of widely used rail bases and accommodates O2 clips for use with oxygen masks. Size Medium rails shall weigh no more than 85g. Ballistic Visor - The ballistic visor shall attach to the front mount at the standard NVD interface. The ballistic Visor should be available in a Standard or Max Version. The visor must have three positions and have the capability to be in an open, vented or closed position. Operation of the visor mechanism shall be able to be utilized with one hand. The visor shall be able to be donned and doffed using one hand. The visor assembly shall weigh no more than: Standard Version: 280g, Max Version: 335g. The visor system must be able to be used with ballistic eyewear and goggles. The Standard visor system must be able to be worn with an M50 CBRN mask. The visor must offer a removable gasket seal. Ballistic Performance, Fragmentation protection: 1.1g FSP V50 > 235 m/s, tested in accordance with STANAG 2920 Ed2. Optical standards: The visor must pass MCEPS abrasion requirements. Must have replaceable visor lens. The Fragmentation visor must engage with Revision�s Standalone or Interlocking rails The Visor must have three positions. The Visor must be size specific for each sized helmet � small, medium, large, X-large. The visor shall be 6mm think and 15.5 mm cm, Ballistic Performance .17 grain, .22 cal V50 = 350m/s, Blunt impact is greater than 45 J. Ballistic Mandible Guard - The ballistic mandible shall attach to the front mount on the left and right side with slotted guides that can pivot open and closed. Shall allow for one handed operation for quick removal of the mandible. The mandible guard must be doffed and donned without removing the helmet. Ballistic Performance: Fragmentation protection: 1.1g FSP V50 > 670 m/s, tested in accordance with STANAG 2920 Ed2. The mandible guard must resist penetration of a 9mm FMJ in accordance with NIJ 0101.04 at 427 m/s. While installed, the mandible guard must be able to tilt downwards in two positions to enable use with large NVGs and to facilitate hydration. The guard must be able to be brought back to the original position with a quick, hands-free operation. 4-0530-5181, 3, EA; LI 006: Caiman Ballistic Black LG MSS must contain Black High Cut Ballistic Shell, MSS Retention System and Suspension System. High cut helmet: a size Medium helmet shall have a minimum protective surface area of at least 144in2 (929cm2). 4-point retention system with chin cup and adjustable straps. The straps shall have no loose ends. Must also contain the following attachments: Front Mount shall be available in 4 sizes compatible with helmet sizing. Shall not require any modification or additional drill holes. A size Medium Front Mount (configured for PVS-7 or PVS-14) shall weigh no more than 85g. Right and Left Side Rails - shall consist of left and right rails in 4 sizes to fit small through extra-large helmets. Must lock with Front Mount to ensure no rotational movement. Multiple entry points accept widely used rail bases, such as swivel clips, picatinny and winged rail bases. Design shall allow for easy, one-handed attachment of widely used rail bases and accommodates O2 clips for use with oxygen masks. Size Medium rails shall weigh no more than 85g. Ballistic Visor - The ballistic visor shall attach to the front mount at the standard NVD interface. The ballistic Visor should be available in a Standard or Max Version. The visor must have three positions and have the capability to be in an open, vented or closed position. Operation of the visor mechanism shall be able to be utilized with one hand. The visor shall be able to be donned and doffed using one hand. The visor assembly shall weigh no more than: Standard Version: 280g, Max Version: 335g. The visor system must be able to be used with ballistic eyewear and goggles. The Standard visor system must be able to be worn with an M50 CBRN mask. The visor must offer a removable gasket seal. Ballistic Performance, Fragmentation protection: 1.1g FSP V50 > 235 m/s, tested in accordance with STANAG 2920 Ed2. Optical standards: The visor must pass MCEPS abrasion requirements. Must have replaceable visor lens. The Fragmentation visor must engage with Revision�s Standalone or Interlocking rails The Visor must have three positions. The Visor must be size specific for each sized helmet � small, medium, large, X-large. The visor shall be 6mm think and 15.5 mm cm, Ballistic Performance .17 grain, .22 cal V50 = 350m/s, Blunt impact is greater than 45 J. Ballistic Mandible Guard - The ballistic mandible shall attach to the front mount on the left and right side with slotted guides that can pivot open and closed. Shall allow for one handed operation for quick removal of the mandible. The mandible guard must be doffed and donned without removing the helmet. Ballistic Performance: Fragmentation protection: 1.1g FSP V50 > 670 m/s, tested in accordance with STANAG 2920 Ed2. The mandible guard must resist penetration of a 9mm FMJ in accordance with NIJ 0101.04 at 427 m/s. While installed, the mandible guard must be able to tilt downwards in two positions to enable use with large NVGs and to facilitate hydration. The guard must be able to be brought back to the original position with a quick, hands-free operation. 4-0530-5179, 4, EA; LI 007: Caiman Ballistic Black MD MSS must contain Black High Cut Ballistic Shell, MSS Retention System and Suspension System. High cut helmet: a size Medium helmet shall have a minimum protective surface area of at least 144in2 (929cm2). 4-point retention system with chin cup and adjustable straps. The straps shall have no loose ends. Must also contain the following attachments: Front Mount shall be available in 4 sizes compatible with helmet sizing. Shall not require any modification or additional drill holes. A size Medium Front Mount (configured for PVS-7 or PVS-14) shall weigh no more than 85g. Right and Left Side Rails - shall consist of left and right rails in 4 sizes to fit small through extra-large helmets. Must lock with Front Mount to ensure no rotational movement. Multiple entry points accept widely used rail bases, such as swivel clips, picatinny and winged rail bases. Design shall allow for easy, one-handed attachment of widely used rail bases and accommodates O2 clips for use with oxygen masks. Size Medium rails shall weigh no more than 85g. Ballistic Visor - The ballistic visor shall attach to the front mount at the standard NVD interface. The ballistic Visor should be available in a Standard or Max Version. The visor must have three positions and have the capability to be in an open, vented or closed position. Operation of the visor mechanism shall be able to be utilized with one hand. The visor shall be able to be donned and doffed using one hand. The visor assembly shall weigh no more than: Standard Version: 280g, Max Version: 335g. The visor system must be able to be used with ballistic eyewear and goggles. The Standard visor system must be able to be worn with an M50 CBRN mask. The visor must offer a removable gasket seal. Ballistic Performance, Fragmentation protection: 1.1g FSP V50 > 235 m/s, tested in accordance with STANAG 2920 Ed2. Optical standards: The visor must pass MCEPS abrasion requirements. Must have replaceable visor lens. The Fragmentation visor must engage with Revision�s Standalone or Interlocking rails The Visor must have three positions. The Visor must be size specific for each sized helmet � small, medium, large, X-large. The visor shall be 6mm think and 15.5 mm cm, Ballistic Performance .17 grain, .22 cal V50 = 350m/s, Blunt impact is greater than 45 J. Ballistic Mandible Guard - The ballistic mandible shall attach to the front mount on the left and right side with slotted guides that can pivot open and closed. Shall allow for one handed operation for quick removal of the mandible. The mandible guard must be doffed and donned without removing the helmet. Ballistic Performance: Fragmentation protection: 1.1g FSP V50 > 670 m/s, tested in accordance with STANAG 2920 Ed2. The mandible guard must resist penetration of a 9mm FMJ in accordance with NIJ 0101.04 at 427 m/s. While installed, the mandible guard must be able to tilt downwards in two positions to enable use with large NVGs and to facilitate hydration. The guard must be able to be brought back to the original position with a quick, hands-free operation. 4-0530-5177, 3, EA; Solicitation and Buy Attachments ***Question Submission: Interested Offerers must submit any questions concerning the solicitation at the earliest time possible to enable the Buyer to respond. Questions must be submitted by using the 'Submit a Question' feature at www.UnisonMarketplace.com. Questions not received within a reasonable time prior to close of the solicitation may not be considered.*** For this solicitation, MICC End User intends to conduct an online competitive reverse auction to be facilitated by the third-party reverse auction provider, Unison, Inc. Unison Marketplace has developed an online, anonymous, browser based application to conduct the reverse auction. An Offeror may submit a series of pricing bids, which descend in price during the specified period of time for the aforementioned reverse auction. MICC End User is taking this action in an effort to improve both vendor access and awareness of requests and the agency's ability to gather multiple, competed, real-time bids. All responsible Offerers that respond to this solicitation MUST submit the pricing portion of their bid using the online exchange located at www.UnisonMarketplace.com. There is no cost to register, review procurement data or make a bid on www.UnisonMarketplace.com. Offerers that are not currently registered to use www.UnisonMarketplace.com should proceed to www.UnisonMarketplace.com to complete their free registration. Offerers that require special considerations or assistance may contact Marketplace Support at 1.877.933.3243 or via email at marketplacesupport@unisonglobal.com. Offerers may not artificially manipulate the price of a transaction on www.UnisonMarketplace.com by any means. It is unacceptable to place bad faith bids, to use decoys in the www.UnisonMarketplace.com process or to collude with the intent or effect of hampering the competitive www.UnisonMarketplace.com process. Should Offerers require additional clarification, notify the point of contact or Marketplace Support at 1.877.933.3243 or marketplacesupport@unisonglobal.com.Use of Unison Marketplace: Buyers and Sellers agree to conduct this transaction through Unison Marketplace in compliance with the Unison Marketplace Terms of Use. Failure to comply with the below terms and conditions may result in offer being determined as non-responsive. The offeror must comply with the following commercial item terms and conditions: FAR 52.252-1, Solicitation. Provisions Incorporated by Reference; FAR 52.212-1, Instructions to Offerors; 52.212-3, Offeror Representations and Certifications; FAR 52.211-6, Brand name or Equal. The following clauses apply to this solicitation: FAR 52.212-4, Contract Terms and Conditions � Commercial Items. The following FAR clauses in paragraph (b) of FAR clause 52.212-5, Contract Terms and Conditions Required To Implement Statutes or Executive Orders-Commercial Items, apply: 52.204-10, Reporting Executive Compensation and First Tier Subcontract Awards; 52.219-6, Notice of Total Small Business Set-Aside; 52.219-28, Post Award Small Business Program Rerepresentation; 52.222-3, Convict Labor; 52.222-19, Child Labor-Cooperation with Authorities and Remedies; 52.222-21, Prohibition of Segregated Facilities; 52.222-26, Equal Opportunity; 52.222-36, Affirmative Action for Workers with Disabilities; 52.225-13, Restrictions on Certain Foreign Purchases; 52.232-33, Payment by Electronic Funds Transfer--System for Award Management. 52.233-4, Applicable Law for Breach of Contract Claim; The following DFARS clauses apply: DFARS 252.04-7004, Alternate A System for Award Management; 252.211-7003, Item Identification and Valuation; 252.225-7002, Qualifying Country Sources as Subcontractors; 252.232-7010, Levies on Contract Payments; 252.203-7000, Requirements Relating to Compensation of Former DoD Officials; 252.225-7001, Buy American Act and Balance Of Payments Program; 252.225-7036, Buy American Act -- Free Trade Agreements -- Balance of Payments Program; 252.232-7003, Electronic Submission of Payment Requests; 252.247-7023, Primary and ALT III, Transportation of Supplies by Sea. IAW 52.204-7 System for Award Management (SAM) Registration (July 2013), the offeror must be registered in SAM and fully input their Representations and Certifications for a complete record. Information can be found at http://www.sam.gov or by calling 866-606-8220, or 334-206-7828 for international calls. 52.204-13 - System for Award Management Maintenance Shipping is FOB Destination CONUS (CONtinental U.S.). New Equipment ONLY. NO USED OR REMANUFACTURED PRODUCTS WILL BE ACCEPTED. Submitted Quotes will be valid for 45 days after the auction closing. This solicitation is issued as a Request for Quotation (RFQ), not an invitation for bid (IFB).). IAW FAR 52.252-2 Clauses Incorporated by Reference, the full text of FAR and DFARS Clauses may be accessed electronically at http://farsite.hill.af.mil; and are current to the most recent revision dates posted on this site. The associated North American Industrial Classification System (NAICS) code for this procurement can be found. The small business size standard for that NAICS code can be found at https://www.sba.gov/sites/default/files/files/Size_Standards_Table.pdf ""AMC-Level Protest Program If you have complaints about this procurement, it is preferable that you first attempt to resolve those concerns with the responsible contracting officer. However, you can also protest to Headquarters (HQ), Army Materiel Command (AMC). The HQ AMC-Level Protest Program is intended to encourage interested parties to seek resolution of their concerns within AMC as an Alternative Dispute Resolution forum, rather than filing a protest with the Government Accountability Office (GAO) or other external forum. Contract award or performance is suspended during the protest to the same extent, and within the same time periods, as if filed at the GAO. The AMC protest decision goal is to resolve protests within 20 working days from filing. To be timely, protests must be filed within the periods specified in FAR 33.103. If you want to file a protest under the HQ AMC-Level Protest Program, the protest must request resolution under that program and be sent to the address below. All other agency-level protests should be sent to the contracting officer for resolution. Headquarters U.S. Army Materiel Command Office of Command Counsel 4400 Martin Road Rm: A6SE040.001 Redstone Arsenal, AL 35898-5000 Fax: (256) 450-8840 Packages sent by FedEx or UPS should be addressed to: Headquarters U.S. Army Materiel Command Office of Command Counsel 4400 Martin Road Rm: A6SE040.001 Redstone Arsenal, AL 35898-5000 Fax: (256) 450-8840 The AMC-Level Protest procedures are found at: http://www.amc.army.mil/pa/COMMANDCOUNSEL.asp. If internet access is not available, contact the contracting officer or HQ, AMC to obtain the HQ AMC-Level Protest Procedures."" ""52.204-9, Personal Identity Verification of Contractor Personnel; 52.204-10, Reporting Executive Compensation and First-Tier Subcontract Awards; 52.222-41, Service Contract Act; 52.237-2, Protection of Government Buildings, Equipment and Vegetation; 252.201-7000, COR Clause; 252.223-7006, Prohibition On Storage And Disposal Of Toxic And Hazardous Materials; 252.243-7001, Pricing of Contract Modifications; 252.246-7000, Material inspection and receiving report"" Representation by Corporations Regarding an Unpaid Tax Liability or a Felony Conviction under any Federal Law. Wide Area WorkFlow Payment Instructions 252.204-7012 Safeguarding of Unclassified Controlled Technical Information All deliveries shall be palletized when the material exceeds 250 lbs. (excluding the pallet), or exceeds 20 cubic feet, to comply with the requirements of Department of the Army Pamphlet 700-32 and MIL-STD-147E. This is currently an unfunded requirement with a high expectation that funds will be available. When and if funds become available a contract will be awarded at that time. IAW FAR 52.212-2; Evaluation - Commercial Items, the following factor shall be used to evaluate offers: Technical capability of the item offered to meet the Government requirement and price. Technical capability is more important than price. No multiple awards will be made. Quotes received through Unison Marketplace will be evaluated and awarded on an ?all-or-nothing? basis. Wide Area WorkFlow Payment Instructions Please address your questions through the Unison Marketplace buy. If your questions are not being answered in a timely manner, please send your question to the S2P2 Contracting Officer - usarmy.drum.acc-micc.mbx.micc@mail.mil or call 315-772-5582.
Web Link: SAM.gov Permalink
(https://beta.sam.gov/opp/97696e487b88429eab612c2631cf6a59/view)
Place of Performance: Address: Pueblo, CO 81006, USA; Zip Code: 81006; Country: USA
Record: SN05568935-F 20200223/200221231700 (samdaily.us)
Source: SAM.gov Link to This Notice
(may not be valid after Archive Date)

| FSG Index | This Issue's Index | Today's SAM Daily Index Page |

Loren Data's SAM Daily™

84 -- Combat Helmets