SAMDaily.us | SRCSGT | 13 | JM92 Impulse Cartridge

SAMDAILY.US - ISSUE OF JULY 18, 2020 SAM #6806
SOURCES SOUGHT

13 -- JM92 Impulse Cartridge

Notice Date: 7/16/2020 8:24:25 AM
Notice Type: Sources Sought
NAICS: 325920 — Explosives Manufacturing
Contracting Office: NSWC INDIAN HEAD EOD TECH DIV INDIAN HEAD MD 20640-1533 USA
ZIP Code: 20640-1533
Solicitation Number: N0017420SN0039
Response Due: 7/31/2020 5:00:00 AM
Archive Date: 08/15/2020
Point of Contact: Sarah Hayden
E-Mail Address: sarah.n.hayden@navy.mil
(sarah.n.hayden@navy.mil)
Description: JM92 Impulse Cartridge� 1.0�� INTRODUCTION This is a Sources Sought Synopsis. This synopsis neither constitutes a Request for Proposal, nor does it restrict the Government from an ultimate acquisition approach. This synopsis should not be construed as a commitment by the Government for any purpose. Requests for solicitation will not receive a response. All information is to be submitted at no cost or obligation to the U.S. Government. The U.S. Government reserves the right to reject, in whole or in part, any input as a result of this market survey. The U.S. Government is not obligated to notify respondents of the results of this survey. If a formal solicitation is generated at a later date, a solicitation notice will be published. No award will be made as a result of this market survey. The Naval Surface Warfare Center Indian Head Explosive Ordnance Disposal Technology Division, (NSWC IHEODTD), is pursuing the procurement of the CCU-165/B (DODIC JM92) stores release cartridge. The JM92 cartridge is a Hazards of Electromagnetic Radiation to Ordnance safe cartridge used as a power source for the ejection of stores from aircraft missile launchers and bomb racks. This procurement consists of the manufacturing of complete cartridges, loaded ignition elements in cut down cases, and inert glass sealed headers. �NSWC IHEODTD will evaluate the JM92 sub-assemblies and cartridges in this procurement through Qualification testing. 1.1. SCOPE The contractor shall provide all labor, material facilities (except for items listed as Government Furnished Information (GFI) or Government Furnished Material (GFM)), and facilities to manufacture the JM92 sub-assemblies and cartridges. The contractor shall also perform all the required sub-assembly testing and in-process inspections defined in the Technical Data Package (TDP). All test data, inspection, and certification documentation shall be provided to NSWC IHEODTD. � 2.0 APPLICABLE DOCUMENTS The following documents are applicable to the extent stated within this SOW. �In the event of a conflict between the text of this SOW and other documentation such as test plans, drawings, specifications, or any documents cited herein, NSWC IHEODTD will provide written guidance as to what shall take precedence. Document Number � � � � � � � � � � � � � � � � � � � � � � � �Document Title IHDIVNAVSURFWARCENINST 9070.1 � � � � � � �DESIGN REVIEWS DATA LIST 3205AS357�� CARTRIDGE, IMPULSE ASSEMBLY�� MIL-D-81303�� DESIGN AND EVALUATION OF CARTRIDGES FOR STORES SUSPENSION EQUIPMENT MIL-DTL-32291�� DETAIL SPECIFICATION, CARTRIDGE, IMPULSE, CCU-165/B� MIL-D-21625G�� DESIGN AND EVALUATION OF CARTRIDGES FOR CARTRIDGE ACTUATED DEVICES�� MIL-DTL-23659F�� DETAIL SPECIFICATION, GENERAL DESIGN SPECIFICATION FOR INITIATORS, ELECTRIC 3.0 �� REQUIREMENTS�� 3.1 �� The Contractor shall host a kick-off meeting within 15 days of contract award to address the production, testing, and deliverable requirements of the contract. In addition, the Contractor shall present the estimated schedule to completion per CDRL A001.� 3.2�� The Contractor shall provide monthly progress reports per CDRL A002. Monthly progress reports shall include current schedule updates. 3.3�� Prior to complete assembly of the JM92 cartridges, the Contractor shall perform all sub-assembly level tests presented in Table I with reference to MIL-DTL-32291 and DL3205AS357 within the TDP. �The Contractor shall deliver all sub-assembly test data per CDRL A003. Table I: Sub-Assembly Testing 3.4�� Prior to the start of manufacture of the complete assembly of the JM92 cartridges, the Contractor shall conduct a Production Readiness Review (PRR) in accordance with IHDIVNAVSURFWARCENINST 9070.1. The PRR shall include a presentation and review of the manufacturing build order, procedures, material certifications, in-process test results, and parts. In addition, the Contractor shall provide a tour of the manufacturing facilities. The Government will provide written approval to begin with manufacturing. �The Contractor shall submit all PRR material per CDRL A004.� 3.5 �� The Contractor shall perform the in-process 100% inspections on the levels of assembly presented in Table II on the complete production lot with reference to MIL-DTL-32291 and DL3205AS357 within the TDP. The Contractor shall deliver this inspection data per CDRL A005. Table II: 100% Inspections on Cartridge Sub-Assemblies and Assembly 3.6�� The Contractor shall manufacture and deliver the following sub-assemblies and complete assemblies to the requirements of the TDP: a.�� Twenty-five (25) Header, Bridgewire and Charge Holder Assemblies (Drawing 3205AS358)� b.�� Twenty-five (25) Header, Glass Seals (Drawing 3205AS359) c.�� Twenty-five (25) Cartridge Case and Ignition Element Assemblies (Modified) (Drawing 3205AS325) d.�� One Thousand (1,000) JM92 Impulse Cartridges (Drawing 3205AS357) 3.7�� The Contractor shall manufacture the JM92 cartridges in the final production configuration using the equipment, tooling, and process which will be used for regular production of the cartridges. �All parts and materials shall be of the same design as will be used for regular production lots, and shall be obtained from the same sources of supply the Contractor intends to use for the Qualification lot. 3.8�� The JM92 cartridges shall meet all of the requirements of the following specifications: MIL-D-81303, MIL-DTL-32291, MIL-D-21625G, and MIL-DTL-23659F. 3.9�� The Contractor is to submit an Ammunition Data Card for the Qualification lot per CDRL A006. 4.0�� DELIVERABLES a.�� Data i.�� Schedule to Completion � CDRL A001 ii.�� Monthly Progress Reports � CDRL A002 iii.�� Sub-assembly Test Results- CDRL A003 iv.�� Production Readiness Review Material- CDRL A004 v.�� 100% Inspection Data- CDRL A005 vi.�� Ammunition Data Card- CDRL A006 b.�� Materials: i.�� Twenty-five (25) Header, Bridgewire and Charge Holder Assemblies (Drawing 3205AS358)� ii.�� Twenty-five (25) Header, Glass Seals (Drawing 3205AS359) iii.�� Twenty-five (25) Cartridge Case and Ignition Element Assemblies (Modified) (Drawing 3205AS325) iv.�� One Thousand (1,000) JM92 Impulse Cartridges (Drawing 3205AS357) 6.0 TECHNICAL POINT(S) OF CONTACT John Venincasa NSWC IHEODTD 4393 Benson Road, Suite 114 Indian Head, MD 20640 301-744-2102 7.0 CONTRACTING OFFICER�S REPRESENTATIVE Christina Fish-DeAtley NSWC IHEODTD 4393 Benson Road Indian Head, MD 20640 301-744-2313 8.0 SHIPPING ADDRESS� a.�� Class 1 material shall be shipped to: Explosives Scales Facility ATTN: John Venincasa (x2102) 5021 Safe Haven Way Indian Head, MD �20640-5173� b.�� All inert material, all documentation, MSDS, and test information shall be shipped to shall be shipped to: ATTN: John Venincasa CAD/PAD Department NSWC IHEODTD� 4393 Benson Road Suite 114 Indian Head, MD 20640-5092 �� 9.0 ITAR Certification Requirement (unclassified controlled technical information)� This procurement includes unclassified controlled technical information assigned a restricted distribution statement which is export controlled. To receive this unclassified controlled technical information, an Offeror must be currently certified through the United States/Canada Joint Certification Program. To become certified for receipt of the technical documents, a U.S. Offeror must submit a completed DD Form 2345 to the U.S./Canada Joint Certification Office. Canadian Offerors may submit either a completed DD Form 2345 or DSS-MAS 9379 for certification. In addition, a copy of the company's State/Provincial Business License, Incorporation Certificate, sales Tax Identification Form or other documentation which verifies the legitimacy of the company must accompany all DD Form 2345s. Additional information on the Joint Certification Program and a checklist for completion of the DD Form 2345 is available at the following website: http://www.dla.mil/HQ/InformationOperations/Offers/Products/LogisticsApplications/JCP/. Offerors are encouraged to apply for certification as early as possible in order for processing and receipt of information to be completed in sufficient time to prepare a proposal before solicitation closing.� 10.0 Interested Vendors All interested sources shall provide a company brochure or list of specifications, organization name, address, a point of contact, phone number, fax number, e-mail address, business size, taxpayer identification number, DUNS number, and CAGE Code. All responding sources must email their response submissions no later than 31 JUL 2020 to: 1) Naval Surface Warfare Center, Indian Head Explosive Ordnance Disposal Technology Division. John Venincasa NSWC IHEODTD 4393 Benson Road, Suite 114 Indian Head, MD 20640 301-744-2102 john.venincasa@navy.mil 2) Naval Surface Warfare Center, Indian Head Explosive Ordnance Disposal Technology Division Attn: Sarah Hayden, Contract Specialist sarah.n.hayden@navy.mil ��
Web Link: SAM.gov Permalink
(https://beta.sam.gov/opp/359051de14574492aee163de18ec8c4d/view)
Place of Performance: Address: Indian Head, MD 20640, USA; Zip Code: 20640; Country: USA
Record: SN05724179-F 20200718/200716230204 (samdaily.us)
Source: SAM.gov Link to This Notice
(may not be valid after Archive Date)

| FSG Index | This Issue's Index | Today's SAM Daily Index Page |

Loren Data's SAM Daily™

13 -- JM92 Impulse Cartridge