SOLICITATION NOTICE
95 -- Square Forgings
- Notice Date
- 11/20/2020 5:46:35 AM
- Notice Type
- Combined Synopsis/Solicitation
- NAICS
- 331221
— Rolled Steel Shape Manufacturing
- Contracting Office
- DLA MARITIME - NORFOLK PORTSMOUTH VA 23709-5000 USA
- ZIP Code
- 23709-5000
- Solicitation Number
- SPMYM121Q0004
- Response Due
- 12/1/2020 4:00:00 AM
- Archive Date
- 12/16/2020
- Point of Contact
- Craig Harmon, Phone: 757-278-5055
- E-Mail Address
-
craig.harmon@dla.mil
(craig.harmon@dla.mil)
- Small Business Set-Aside
- SBA Total Small Business Set-Aside (FAR 19.5)
- Description
- The Defense Logistics Agency (DLA), Land and Maritime located at the Norfolk Naval Shipyard, Portsmouth, Virginia, Contracting Division intends to negotiate a firm fixed price contract, for the items listed below utilizing the North American Industry Classification System Code 331221 �Rolled Steel Shape, Iron and Steel Bars and Rods. This requirement will be set aside as a 100% Small Business concern. This requirement is being solicited as Control Industrial Material (CIM), which requires written verification that the chemical and mechanical properties have been determined and are acceptable, IAW military specification MIL-DTL-1222, as it applies to the below document numbers: �The Contract Line Items (CLINs) are as follows. 0301B741 Square Forging, five (5) each.� CIM Item FIVE (5) SQUARE FORGINGS THAT ARE 3 �� WIDTH (+1/4�/-0�), 3 �� HEIGHT (+1/4�/-0�), AND 72� LONG (+1/2�/-0�), MIL-S-24093A, CLASS C, TYPE 1 0301B742 Square Forging, five (5) each.� CIM Item FIVE (5) SQUARE FORGINGS THAT ARE 5 �� WIDTH (+1/4�/-0�), 5 �� HEIGHT (+1/4�/-0�), AND 55� LONG (+1/2�/-0�), MIL-S-24093A, CLASS C, TYPE 1 The following ordering data applies to both 0301B741 and 0301B742. This ordering data is for five (5) square forgings that are 3 ��(inches)� in width, 3 ��(inches)� in height, and 72� (inches) long, and five (5) square forgings that are 5 ��(inches)� in width, 5 ��(inches)� in height, and 55� (inches) long, all conforming to MIL-S-24093 Class C Type 1. NOTE: Ultrasonic inspection certification, material certification, and mechanical property certification is required to be attached to the material when shipped. MIL-S-24093A �Steel Forgings, Carbon Alloy, Heat Treated 5 November 1991 Class C Type 1 Refer to the latest revision of documents listed in 2.1 and 2.2, as applicable. N/A N/A N/A Transverse mechanical properties required N/A Five (5) Square forgings that are 3 �� Width (+1/4�/-0�), 3 �� Height (+1/4�/-0�), and 72� Long (+1/2�/-0�) � Five (5) Square forgings that are 5 �� Width (+1/4�/-0�), 5 �� Height (+1/4�/-0�), and 55� Long (+1/2�/-0�) � N/A Mark IAW 3.18.1 of MIL-S-23284A on one of the flat faces of the forging. Ultrasonic inspections are required N/A Commercial packaging to MIL-DTL-2845E, Level A preservation to Method 20 or 30 of MIL-STD-2073-1C The following ordering data applies to both 0301B741 and 0301B742. Provide written verification that the chemical and mechanical properties have been determined and are acceptable IAW MIL-S-24093A the required specification 0301-B741 AND 0301-B742 ��������������� a.) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable.� All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification.� Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative.� The name and title shall be clearly legible.� Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents.� The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements.� Statements on material certification documents must be positive and unqualified.� The material certification data reports shall include quantitative data representing the actual values obtained during testing. ��������������� b.) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer.� Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.� In the case of a finished product identified by a lot number manufactured from a start material identified by a heat number, the final test reports performed on the finished product samples shall be marked with the lot number.� The test reports for the raw material shall be marked with the heat number of that material. ��������������� c.) Test reports labeled ""Typical,"" those with words such as ""to the best of our knowledge"" or ""we believe the information contained herein is true"" or those that have results transcribed from other reports or documents, or test reports with the heat/lot/batch number information handwritten on them are not acceptable. � ��������������� d.) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222 K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed (i.e., fasteners manufactured and then solution annealed and age hardened, etc.).� This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process. ��������������� e) Certifications for QQ-N-286 Rev G materials shall show that slow strain rate tensile {SSRT} test of �start material� has been accomplished per QQ-N-286 Rev G requirements. ��������������� f.) Where headed fastener specifications require a yield strength test AND a wedge tensile test, a separate (new, untested) fastener is required for each of the two test methods, and both of these tests shall be reported. NOTE:� This does not apply to steel hex head fasteners (grades 2, 5, 8, B7, and B16) are certified to a proof load and NOT yield strength; therefore, this issue does NOT apply to those fasteners. NOTE:� This does apply to All CRES and non-ferrous bolts and screws, and ALL steel socket head cap screws (grade A574 and 4340). Wedge tensile test a required test for including ones that had their yield strength and tensile strength certified by alternative testing IAW MIL-DTL-1222. �
- Web Link
-
SAM.gov Permalink
(https://beta.sam.gov/opp/c1b5467ede634895b0a321c74ee66158/view)
- Place of Performance
- Address: Portsmouth, VA 23709, USA
- Zip Code: 23709
- Country: USA
- Zip Code: 23709
- Record
- SN05858288-F 20201122/201120230145 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |