SOLICITATION NOTICE
59 -- FY21-19865: LCU Interface CCA's
- Notice Date
- 3/8/2021 7:28:38 AM
- Notice Type
- Combined Synopsis/Solicitation
- NAICS
- 334418
— Printed Circuit Assembly (Electronic Assembly) Manufacturing
- Contracting Office
- COMMANDING OFFICER PORT HUENEME CA 93043-5007 USA
- ZIP Code
- 93043-5007
- Solicitation Number
- N6339421Q0025
- Response Due
- 3/19/2021 3:00:00 PM
- Archive Date
- 04/03/2021
- Point of Contact
- Brian Carpenter
- E-Mail Address
-
brian.carpenter1@navy.mil
(brian.carpenter1@navy.mil)
- Small Business Set-Aside
- SBA Total Small Business Set-Aside (FAR 19.5)
- Description
- Please see attached. ***Updated 2/24/21 To answer the following questions asked: 1.) What testing will be performed by the government vs. by the manufacturer? The Government will perform all testing, including conformal coating.� The Government will return any failed CCAs to the vendor for repair. 2.) What is the NSN for part number 7572262-9? There�s no NSN for the CCA p/n 7572262-9. 3.) Can the gerber files needed for this solicitation please be uploaded? We are finallizing gathering the files and will get them uploaded ASAP. Once uploaded all vendors interested will need to request access.� ***Updated 2/24/21 to add the following statement in regards to the gerber files: Once your restricted access has been approved for the FY21-19865 Drawings pdf under attachments, please reach out to Brian Carpenter at brian.carpenter1@navy.mil to request the gerber files. They will then be sent via secure format to the requesting email. ***Updated 2/26/21 to answer the following questions asked: 1.) The process is calling out for both conductive and non-conductive fill. Can the non-conductive fill be changed to solder mask fill? The drawing specifically says to use a non-conductive resin. Please build in accordance with the drawings. 2.) On drawing 7572257, note 5a states that the board manufacturer shall select materials to meet the requirements specified. Under note 5b, it states that Prepreg material shall conform to standards. Our suppliers have come back to us requesting exact stack ups calling out the core thicknesses and prepregs. Our suppliers have come back stating that they can control necessary impedance, but there are varying parameters to get this result. Therefore, UST is requesting stack up documentation calling out the core thicknesses and Prepregs. Please advise if you can provide this information to us. The board manufacturer should recommend a stack-up that meets the requirements of the drawing. We can review and approve if needed. 3.)�Is it okay if we use different manufacturers for a part if it is the same part number? Example: on the 7572256-9 parts list P/N: CWR09HC106KB has the change code for AVX but Kemet also make the same part and it is identical. See attached. Can we use the other part?� No, it is not ok to use a part from a different manufacturer.� ***Updated 3/3/21 to incorporate the following changes: �1.) Answer the following questions asked by industry: Authorized distribution for part # JS28F256P33BFE (find 84) on the 1553 CCA is claiming the device is obsolete. Do you have an alternate for us to quote? Part # JS28F256P33BE will be provided as GFM. Part # 7104546 (find 45) on BOM does not have a manufacturers part number and the drawing was not included in the TDP, please provide drawing or manufacturer�s part number. Once your restricted access request has been approved through beta.sam.gov please email Contract Specialist Brian Carpenter at brian.carpenter1@navy.mil to request. These will be sent to industry via DoD Safe. IS61WV102416BLL-10 (find 51) and MT48LC16M16A2P-6AIT (find 7) are listed as DNP devices, so they should be ignored, correct? Yes, these should be ignored. Select parts have a requirement for re-tinning and reference drawing WS20120, please provide spec. Once your restricted access request has been approved through beta.sam.gov please email Contract Specialist Brian Carpenter at brian.carpenter1@navy.mil to request. These will be sent to industry via DoD Safe. Assembly # 7572256, Line # 85, Part # 5962-8761701XA is obsolete. Please advise. 5962-8761701XA is still active from particular vendors.� They can be purchased from the active vendors. 2.)�Amend the solicitation to include the following clauses for GFP. A new amended solicitation has been attached in the documents section. FAR 52.245-1 Government Property FAR 52.245-9 Use and Charges DFARS 252.211-7007 Reporting of Government-Furnished Property DFARS 252.245-7001 Tagging, Labeling, and Marking of Government-Furnished Property DFARS 252.245-7002 Reporting Loss of Government Property DFARS 252.245-7003 Contractor Propert Management System Administration DFARS 252.245-7004 Reporting, Reutilization, and Disposal 3.) Extend the solicitation through 3/19/2021 to allow industry time to make adjustments for the above changes. ***Updated 3/8/21 to answer the following question asked by industry: 1.)�In the notes on the solicitation it states that part #: 5962-8761701XA for line #: 85 of assembly #: 7572256�is still active from particular vendors and can be purchased from those active vendors. Can you please indicate what vendors indicate this part as being active other than Arrow so we can contact them for a quote? This part is still active for DLA, C-Mac. API Electric, Micropac, and Anaren.
- Web Link
-
SAM.gov Permalink
(https://beta.sam.gov/opp/98f16711192c4526ba4a961bb74c044f/view)
- Record
- SN05936147-F 20210310/210308230120 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |