SOURCES SOUGHT
93 -- Sources Sought for a series of fabricated injection molds compatible with the Government owned Nissei FNX110-18A Injection Molding Unit
- Notice Date
- 4/13/2022 4:24:08 AM
- Notice Type
- Sources Sought
- NAICS
- 326199
— All Other Plastics Product Manufacturing
- Contracting Office
- W6QK ACC-APG ADELPHI ADELPHI MD 20783-1197 USA
- ZIP Code
- 20783-1197
- Solicitation Number
- W911QX-22-Q-0085
- Response Due
- 4/20/2022 8:59:00 AM
- Point of Contact
- Adrian Barber, Phone: 3013941503
- E-Mail Address
-
adrian.t.barber.civ@army.mil
(adrian.t.barber.civ@army.mil)
- Description
- (11) A. Objective: To find sources that are qualified to meet the supplies/services as listed in section 11B. Note that the specific requirements in section C are subject to change prior to the release of any solicitation. B. Salient Characteristics �The Government requires a series of fabricated injection molds compatible with the Government-owned Nissei FNX110-18A Injection Molding Unit with the following minimum specifications:� All molds shall contain guided ejector system, hardened S-7 steel core and cavity inserts, straight locks (as necessary), and thermal insulator plates. All molds shall be machined to receive RJG pressure transducers. All molds shall be suitable for injection molding of commercially available grades of commodity polymers (polycarbonate, acrylonitrile-butadiene-styrene, polypropylene, etc.), as well as high temperature engineering resins (polyphenyl sulfone, polyphenylene sulfide, polyether ether ketone, high temperature nylons). All molds shall be durable to use with moderate to high loadings of modifiers and fillers, such as glass fiber, minerals (alumina, blanc fixe, titanium dioxide (TiO2), inorganic pigments), and organics (carbon fiber, cellulose, organic pigments). All molds shall be suitable to withstand melt temperatures upwards of 300-400oC and run at mold temps from 20-250oC for extended periods. Required Molds: Master Unit Die (MUD) Frame to allow use of MUD set dies.� 09/09 U Frame (UF) 321 Mold Base constructed of Pre-hard #2 Steel with a 2.5� hole and no sprue. The MUD set mold bases shall contain a guided ejector system, straight locks (as necessary), hardened S-7 core and cavity inserts, thermal insulator plates, be machined to receive RJG pressure transducers, and be delivered with transducers installed. Two (2) cavity 8� x 5� MUD set for Tensile Bar Type V, according to the below dimensions.� Parts shall be edge gated. Four (4) cavity 5� x 8� MUD set to produce a tube of dimensions outer diameter = 11.6mm, inner diameter = 9.6mm, length = 25mm.� Parts shall be side gated with two (2) pinpoint gates per part Four (4) cavity 5� x 8� MUD set to produce a tube of dimensions OD = 11.6mm, ID = 9.6mm, length = 25mm.� Parts shall be diaphragm gated. Two (2) cavity MUD set 5� x 8� to produce a standard IZOD impact specimen according to the dimensions diagrammed below.� Parts shall be edge gated.� Also included shall be a set of inserts to change from un-notched to notched IZOD impact specimens. Standard two (2) cavity mold 20� x 8� for Tensile Bar Type II according to the below dimensions.� Parts shall be edge gated. One (1) cavity, 3-plate mold 16� x 12� for square plaque 6� x 6� x 1mm ASTM D638 Tensile Bar Specifications.� All dimensions in mm. Izod Notched and Un-Notched Test Bar Specifications. C. Responses: All interested parties should notify this office in writing, mail, fax, or e-mail within the posted date.� Responses shall include: To what extent each of the specifications can be met. �Include your type of business (i.e., commercial, academia), whether your organization is classified as a large or small business based on the 750-employee standard that accompanies NAICS code 326199. If a small business, you must also list any small disadvantaged status you hold [HUBZone, 8(a), Service-Disabled Veteran Owned Small Business (SDVOSB), Women Owned Small Business (WOSB), Economically Disadvantaged Women-Owned Small Business (EDWOSB), etc.]. Past experience/ performance through the description of completed projects. (12) Responses to this sources sought are due no later than 5:00 PM eastern standard time 20 April 2022. Submissions should be emailed to Adrian Barber, adrian.t.barber.civ@army.mil. �� Questions concerning this sources sought may be directed to Adrian Barber at adrian.t.barber.civ@army.mil or 301-394-1503. �Please be advised that .zip and .exe files cannot be accepted. �(13) Place of Contract Performance: Contractor/Vendor location. (14) Estimated Delivery Timeframe or Period of Performance: As soon as possible but no later than fifteen (15) weeks After Receipt of Order (ARO).
- Web Link
-
SAM.gov Permalink
(https://sam.gov/opp/5dd8753e81e441ac9f35674deb150f3f/view)
- Place of Performance
- Address: Aberdeen Proving Ground, MD 21005, USA
- Zip Code: 21005
- Country: USA
- Zip Code: 21005
- Record
- SN06297705-F 20220415/220414232740 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |