SOURCES SOUGHT
36 -- One (1) Polymer Processing Equipment
- Notice Date
- 4/14/2022 8:06:08 AM
- Notice Type
- Sources Sought
- Contracting Office
- W6QK ACC-APG ADELPHI ADELPHI MD 20783-1197 USA
- ZIP Code
- 20783-1197
- Solicitation Number
- W911QX-22-R-0016
- Response Due
- 4/21/2022 8:59:00 AM
- Point of Contact
- Crystal L. Demby, Phone: 3013945332
- E-Mail Address
-
crystal.l.demby.civ@mail.mil
(crystal.l.demby.civ@mail.mil)
- Description
- The Government requires one (1) polymer processing equipment with the following minimum specifications: A mobile system for the drying of polymer pellets prior to processing. The system shall be comprised of a cart mounted hopper dryer with a rotary desiccant which can operate in a continuous or batch-wise fashion. It shall offer a drying capacity of roughly 15-20 pounds (lb.)/ hour (hr.) with a 2 cubic ft hopper volume. It shall come equipped with a hopper loader, allowing it to load itself on-demand from a bag or drum of polymer pellets The equipment shall run on 460V 3-phase electrical supply. It shall include a drying monitor capable of monitoring and controlling dewpoint. The heat exchanger shall be air-to-air. A mobile system for the drying of polymer pellets prior to processing. The system shall contain the same criteria as the above, except it shall offer a drying capacity of roughly 25-30lb/hr. with a 3 cubic ft hopper. An oil heating and circulation system, capable of maintaining oil temperature from 70-500Fahrenheit (21.1-260Celcius) and delivering >10Liters/minute flow rate. The unit shall have an air-cooled seal cavity requiring no cooling water for operation. It shall have a digital interface for controlling setpoint. It shall run on 460V 3-phase electrical supply. A screenless mobile granulator for the grinding of injection molding byproducts (sprues, runners, etc.) or reject parts. It shall be capable of throughputs in the range of 20lb/hour with an opening of 10� width by 10� height plus or minus 2�. It shall have a motor delivering 3 plus or minus 0.5 horsepower with a cutter size of 5� to 6�. It shall have a multi-tooth rotor comprised of D2 teeth and cutting wheel. It shall be able to interface with a take-off, by either vacuum or compressed air, to unload directly to a bag or drum. C. Responses: All interested parties should notify this office in writing, mail, fax, or e-mail within the posted date.� Responses shall include: To what extent each of the specifications can be met. � �Include your type of business (i.e., commercial, academia), whether your organization is classified as a large or small business based on the 100-employee standard that accompanies NAICS code 423830. If a small business, you must also list any small disadvantaged status you hold [HUBZone, 8(a), Service-Disabled Veteran Owned Small Business (SDVOSB), Women Owned Small Business (WOSB), Economically Disadvantaged Women-Owned Small Business (EDWOSB), etc.]. � Past experience/ performance through the description of completed projects. � (12) Responses to this sources sought are due no later than 11:59 AM eastern standard time 21 April 2022. Submissions should be emailed to Crystal Demby, crystal.l.demby.civ@army.mil. �� � Questions concerning this sources sought may be directed to Crystal Demby at crystal.l.demby.civ@army.mil or 301-394-5332.� Please be advised that .zip and .exe files cannot be accepted. �(13) Place of Contract Performance: U.S. Army, Adelphi Laboratory Center (ALC), 2800 Powder Mill Road, Adelphi, MD 20783. (14) Estimated Delivery Timeframe or Period of Performance: No later than six (6) months after receipt of Order (ARO).
- Web Link
-
SAM.gov Permalink
(https://sam.gov/opp/264b6f84f4584a77bc69865df493ae97/view)
- Place of Performance
- Address: Aberdeen Proving Ground, MD 21005, USA
- Zip Code: 21005
- Country: USA
- Zip Code: 21005
- Record
- SN06298924-F 20220416/220414234152 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |