SOLICITATION NOTICE
Y -- Montgomery Parking Lot Replacement
- Notice Date
- 8/5/2022 9:17:11 AM
- Notice Type
- Presolicitation
- NAICS
- 236220
— Commercial and Institutional Building Construction
- Contracting Office
- VBA FIELD CONTRACTING (36C10E) WASHINGTON DC 20006 USA
- ZIP Code
- 20006
- Solicitation Number
- 36C10E22R0009
- Response Due
- 8/5/2022 10:00:00 AM
- Archive Date
- 11/03/2022
- Point of Contact
- Tiffany L Garfield, Contract Specialist, Phone: 813-631-2818
- E-Mail Address
-
tiffany.garfield@va.gov
(tiffany.garfield@va.gov)
- Small Business Set-Aside
- SDVOSBC Service-Disabled Veteran-Owned Small Business (SDVOSB) Set-Aside (FAR 19.14)
- Awardee
- null
- Description
- MONTGOMERY VETERANS ADMINISTRATION REGIONAL OFFICE (VARO) 345 Perry Hill Road Montgomery, AL 36109 Statement of Work Parking Lot Replacement OBJECTIVE The Objective of this Statement of Work (SOW) is to define the work activities, deliverables, and timelines a vendor must adhere to in performance of the Repaving, Concrete Curb and Gutter Replacement, and Restriping of the VA Montgomery Regional Office Employee Parking Lot, Visitor Parking Lot, and Samuel J Road. GENERAL To achieve the stated objective, the contractor shall use accepted construction practices in all aspects of the construction, maintenance, and/or repairs associated with the work described herein. The contractor shall demonstrate experience and knowledge with the materials and applications best suited for paving and site work projects. The contractor shall demonstrate a knowledge of approved and appropriate techniques and methods of using these materials and must ensure compliance with applicable codes and VA regulations. SCOPE OF WORK The scope of this project is to demolish, re-asphalt, and restripe the West and East parking lots at the Montgomery VARO as follows: Provide one staging location for the duration of construction. Coordinate limits with COR at the parking bend adjacent to the warehouse on the far side of the employee parking lot. Remove and replace all asphalt in the visitor lot. This lot consists of 39 parking spaces, including 4 handicapped spaces. Remove and replace or clean concrete curb and gutter in this lot. Remove and replace all asphalt in the employee parking lot. This lot consists of 214 parking space; 15 of these are handicapped spaces. Remove and replace or clean concrete curb and gutter in this lot. Perry Hill-Samuel J Intersection. Remove and replace all asphalt drive and remove and replace or clean concrete curb and gutter. Provide proper signage and traffic control to allow visitors and employee access with minimal confusion. Discuss the potential for weekend work in this location with the COR. Samuel J Remove and replace all asphalt drive and remove and replace or clean concrete curb and gutter. Employees will be need to be routed through the main VA campus while this work is complete. Medal of Honor Memorial Dr Samuel J Intersection. Discuss the potential for weekend work in this location with the COR, as this will cut off access to the entire employee parking lot. Once each area is complete, the contractor is to restripe all affected areas. This includes but is not limited to: parking lines, handicapped parking spaces, crosswalks, lane lines, turn arrows, etc. Curb and gutter is to be replaced in all locations where damaged or at the direction of the COR. Clean all curb and gutter existing to remain. Approximate quantities of work are: Remove and replace 99,600 SF of asphalt Remove and Replace 1000 LF of curb and gutter Clean 3750 LF of curb and gutter Restripe to match existing (see attached documentation for more detail) See attached documentation for additional information. Material Requirements The contractor shall provide all necessary supplies and equipment for the successful performance of the scope of work. Contractor shall be responsible for the transportation of materials and labor to and from areas of work. The contractor shall provide all necessary Personal Protective Equipment for employees. Selection and Approval of Materials All Materials Shall be new and selected for their intended purpose. Workmanship shall be of good quality and performed in a skilled manner as determined by the Contracting Officer. Where the contract permits, the selection of materials, products, and equipment shall be performed by the Contractor. All materials and products permanently installed shall be submitted to the Contracting Officer for approval with the following information: Manufacturer Name Relevant Product Data regarding: Nature Appearance Dimensions Performance Capacity Rating Source of Procurement The Contractor shall provide the relevant information in a suitable manner to permit the Government time to evaluate the information against the requirements of the contract. The Contractor shall provide a submittal register three (3) days after contract award showing when shop drawings, samples, mix designs, staging plans, and other submittals shall be made. The Contractor shall be responsible for all costs associated with material and product submissions including shipping costs. Installation or use of any products or materials not approved by Contracting Officer shall be at the risk of the Contractor. Asphalt work All asphalt materials shall be approved by the COR before application. The Contractor shall submit in advance all aggregates and asphalt analysis as per ASTM or AASHTO standards for testing. The test designations listed below are those that are currently specified for use in this project: ASTM C-29 Test for Unit Weight of Aggregate ASTM C-88 Test for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate ASTM C-117 Test for Materials Finer than No. 200 Sieve in Mineral Aggregates ASTM C-127 Test for Specific Gravity and Absorption of Coarse Aggregate ASTM C-128 Test for Specific Gravity and Absorption of Fine Aggregate ASTM C-131 Test for Resistance to Abrasion of Small Size Coarse Aggregate by Use of Los Angeles Abrasion Machine Test for Sieve or Screen Analysis of Fine and Coarse Aggregate ASTM D-75 Sampling Stone, Slag, Gravel, Sand and Stone Block for Use as Highway Materials ASTM D-140 Sampling Bituminous Materials ASTM D-242 Specification for Mineral Filler for Bituminous Paving Mixtures ASTM D-4125 Standard Test Method for Asphalt Content of Bituminous Mixtures by Nuclear Method ASTM D-4791 Flat and Elongated Particles ASTM D-5821 Percent Fracture AASHTO M-29 Fine Aggregate for Bituminous Paving Mix AASHTO M-43 Standard Size of Coarse Aggregate for Highway Construction AASHTO M-156 Requirements for Mixing Plants for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures. AASHTO M-208 Specification for Cationic Emulsified Asphalt AASHTO M-226 Viscosity Graded Asphalt Cement Table Three (3) AASHTO M-320 Standard Specifications for Performance-Graded Asphalt Binder AASHTO T-30 Test for Mechanical Analysis of Extracted Aggregate AASHTO T-43 Test for Specific Gravity of Bituminous Materials AASHTO T-85 Specific Gravity and Absorption of Coarse Aggregate AASHTO T-102 Spot Test of Asphaltic Materials AASHTO T-164 Test for Quantitative Extraction of Bitumen AASHTO T-195 Test for Coated Particles for Bituminous Mixtures AASHTO T-168 Sampling Bituminous Paving Mixtures AASHTO T-304 Uncompacted Void Content of Fine Aggregate (Fine Aggregate Angularity) AASHTO T-308 Determining the Asphalt Content of Hot Mix Asphalt (HMA) by Ignition Method AASHTO T-209 Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures AASHTO T-166 Bulk Specific Gravity of Compacted Bituminous Mixtures Using Saturated Surface Dry Specimens AASHTO T-275 Bulk Specific Gravity of Compacted Bituminous Mixtures Using Paraffin-Coated Specimens Prime Coat Quality of Primer should be cationic emulsion as per ASTM 2397 and AASHTO M-208 Standard Specification for Cationic Emulsified Asphalt. Immediately before applying the prime coat, the full width of the surface shall be cleaned with compressed air. The bituminous material for the prime coat shall be applied by means of bitumen spray tankers. This shall be applied in a single layer at the rate of 0.7 1.5 liters /sq.m and at a temperature not exceeding 70 deg C. This surface shall be cured for 24 hours. The over spread area shall be cured more than 24 hours/ until excess prime coat is evaporated. Binder Course Quality of Binder should be Bituminous Concrete as per ASTM D6373 and AASHTO M-320 Standard Specifications for Performance-Graded Asphalt Binder. Immediately before paving the binder course material, the surface of the prime coat shall be cleaned with compressed air and shall be ensured that the surface is dry. The hot asphalt mix shall be brought from the mixing plant by 6 wheel trucks or trailers. Upon arrival at site, the asphalt mix shall be dumped into the asphalt paver. The asphalt paver shall lay the material to the required thickness and level. The mix shall be compacted as soon as possible after spreading the material. Tandem rollers shall follow the laying operation to carry out breakdown rolling up to temperature of 110-120°C. Pneumatic tired rollers and tandem rollers shall follow the breakdown rolling and sufficient passes shall be made to achieve the required compaction. Rolling shall start from the sides and proceed toward the center. Each trip of the roller shall overlap the pervious trip by at least 30 cm. Roller wheel shall be kept moistened. The roller shall be capable of reversing without backlash and shall be free from worn parts. Heavy rollers shall be used to complete all rolling including elimination of waves caused by the lighter rollers. Full compaction shall be obtained before the asphalt temperature reaches 100°C. Compaction shall be in accordance with specification of relevant standard. Construction joints shall be prepared by cutting the layer vertically down by means of asphalt saw cutting machine or with jack hammer. The joint shall be cleaned well by compressed air and tack coat material shall be applied on the vertical and horizontal surface for better bonding. Extremely good care shall be taken when asphalt is laid at construction joints. Areas inaccessible for heavy rollers shall be compacted with plate compactors or hand tampers. After reaching the base course top level, suitable fill material (dune sand) shall be dumped to the top level of base course on the sides of road shoulders. It shall be leveled, shaped (1:6 ratios) and compacted to 90% maximum dry density. Tack Coat Provide emulsified asphalt conforming to ASTM D 2397 and AASHTO M-208 Standard Specification for Cationic Emulsified Asphalt. Dilute the emulsified asphalt with equal parts water. The base asphalt used to manufacture the emulsion shall show a negative spot when tested in accordance with AASHTO T 102. The material shall be applied at the rate of 0.3 to 0.6 lit/ sq.m at the temperature not exceeding 54 °C above the binder and at where there is a joint with existing asphalt surface. The surface shall be cured for the period as per manufacturer s recommendations until a tacky surface is visible. Surface Course Surface Course Bituminous Concrete design mixtures shall adhere to all ASTM and AASHTO standard specifications for Hot Mix Asphalt stipulated above. The Contractor shall submit, with the design mixtures, the sufficient passes to reach the optimum compaction of the asphalt. The hot asphalt mix shall be spread over the cured surface of tack coat by automatic asphalt paver to the required profile and thickness. The mix shall be compacted as soon as possible after spreading the material. Tandem roller shall follow the laying operation to carry out breakdown rolling up to a temperature of 110- 120°C. Self-propelled rollers and Tandem rollers shall follow the breakdown rolling and sufficient passes shall be made to achieve the required compaction. Rolling shall start from the sides and proceed toward the center. Each trip of the roller shall overlap the previous trip by at least 30 cm. Roller wheels shall be kept moistened. The roller shall be capable of reversing without backlash and shall be free from worn parts. Heavy tandem roller shall be used to complete all rolling including elimination of waves caused by the lighter rollers. Full compaction shall be obtained before the asphalt temperature reaches 80°C. Compaction shall be in accordance with specification of relevant standard. Along curbing, structures, and all places not accessible to the roller, the mixture shall be thoroughly compacted by tampers. Such tampers shall not weigh less than twenty-five (25) pounds and shall have a tamping face of not more than fifty (50) square inches. Immediately before paving the binder course material, the surface of the prime coat shall be cleaned with compressed air and shall be ensured that the surface is dry. No vehicular traffic loads shall be permitted on the newly paved area until adequate stability has been attained and the material has cooled sufficiently to prevent distortion or loss of fines. A minimum period of 12 hours shall be considered after the completion of the rolling. Concrete Curb and Gutter Removal and Replacement of onsite curb and gutter shall be performed to the applicable provisions of the Alabama DOT standard specifications to including, but not limited to: Section 501 Structural Portland Cement Concrete Section 623 Curb, Gutter, and Combination Curb and Gutter Section 800 Materials Section 832 Concrete Joint Fillers, Joint and Crack Sealants, and Waterstop Materials Concrete curb and gutter that will not be removed and replaced will be cleaned with appropriate materials and methods to the approval of the Contracting Officer. Safety & Accident Prevention The Contractor shall provide and maintain work environments and procedures that will: Safeguard the public and Government personnel, property, materials, supplies, and equipment exposed to Contractor operations and activities Avoid interruptions of Government operations and delays in project completion dates Control Costs in the performance of this contract. To these purposes, the Contractor shall: Provide appropriate safety barricades, signs and signal lights, and other traffic control methods. Contractor must use appropriate precautionary measures to protect pedestrians and cars. Comply with the standards issued by any government authority having jurisdiction over occupational health and safety issues. Take any additional measures the Contracting Officer determines to be reasonably necessary for this purpose. Records The Contractor shall maintain an accurate record of exposure data on all accidents incident to work performed under this contract resulting in: Death Traumatic Injury Occupational Disease Damage, Theft, or Loss of Property, Materials, Supplies, or Equipment The Contractor shall report this data to the Contracting Officer at their direction. Subcontracts The Contractor shall be responsible for its subcontractors conduct, workmanship, and their compliance with the terms of this Statement of Work. Written Program Prior to commencing work the Contractor shall submit a written plan for implementing the Safety & Accident Prevention provisions of this Statement of Work. The Contractor shall meet with the Contracting Officer to discuss the overall safety program before starting work. Construction Personnel Removal of Personnel The Contractor shall: Maintain discipline at the site and at all times Take all reasonable precautions to prevent any unlawful, riotous or disorderly conduct by or amongst those employed at the site Take all reasonable precautions for the preservation of peace and protection of persons and property in the vicinity of the project against unlawful, riotous, or disorderly conduct. The Contracting Officer may require in writing that the Contractor remove from the work any employee that the Contracting Officer determines to be: Incompetent Careless Insubordinate Or otherwise objectionable Schedule The objective of scheduled and routine construction operations is to ensure continuous, safe, and satisfactory operation of the Montgomery VA Regional Office. The Contractor shall submit to the Contracting Officer a schedule and description of all tasks which the Contractor will provide as a result of this contract. All work hours MUST be coordinated with the project s COR. All work shall be performed during WHEN hours (Weekends, Holidays, Evenings and Nights) so as not to interfere with normal Hospital functions. However, some VA areas may be conducive to work being completed DURING normal business hours (7:00 am to 5:00 pm, Monday through Friday). All requests for work during normal business hours must be requested by the Contractor at least 14 calendar days in advance. Additionally, construction shall be performed (scheduled and phased) to ensure that exterior egress/ingress areas are completely operational by normal business hours the following workday. Period of Performance is 90 days after Notice To Proceed. Design Requirements A design must be sent to the Contracting Officer before this work is awarded. The Contracting Officer may or may not ask for changes or corrections to the submitted offer before awarding the contract. In case a corrected offer is requested, the corrected offer should be submitted within two (2) working days after the request. Quotation Submittal Quotes indicating contract pricing and materials must be received by the date provided on issue of the Request for Proposal associated with this Statement of Work. Quotes presented after the response date will not be considered in the bid competition. Contracting Officer s Representative (COR) VAAR 842.270 The Contracting Officer may designate in writing one or more Government employees, by name or position title, to take action for the Contracting Officer under this contract. Each designee shall be identified as a Contracting Officer s Representative (COR). Such designation(s) shall specify the scope and limitations of the authority so delegated; provided, that the designee shall not change the terms or conditions of the contract, unless the COR is a warranted Contracting Officer and this authority is delegated in the designation. Modification of Contract The Contractor shall not incur any costs beyond those described in this SOW unless directed otherwise in writing by the Contracting Officer. Any work performed by the Contractor beyond this SOW without written direction from the Contracting Officer will be at the Contractor s own risk and at no cost to the Department of Veterans Affairs. Stop Work At any time during the Project, the Contracting Officer reserves the right to Stop Work for protection of employees or visitors, security, or any other reason at his/her discretion.
- Web Link
-
SAM.gov Permalink
(https://sam.gov/opp/020f48ec0dce4a8599a91bd862c8bcde/view)
- Record
- SN06416214-F 20220807/220805230118 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |