SOURCES SOUGHT
99 -- CNC Vertical Grinding Machines
- Notice Date
- 12/8/2022 10:02:45 AM
- Notice Type
- Sources Sought
- NAICS
- 333517
— Machine Tool Manufacturing
- Contracting Office
- DLA AVIATION RICHMOND VA 23237 USA
- ZIP Code
- 23237
- Solicitation Number
- 22-20-1201
- Response Due
- 12/30/2022 1:00:00 PM
- Point of Contact
- Ashley Saunders, Phone: 8042795277, Gregory Orr, Phone: 8042796354
- E-Mail Address
-
ashley.saunders@dla.mil, gregory.orr@dla.mil
(ashley.saunders@dla.mil, gregory.orr@dla.mil)
- Description
- The DLA-Aviation is issuing this sources sought synopsis as a means of conducting market research to identify parties having an interest in and the resources to support this requirement for two CNC Vertical Grinding Machines. Potential sources must provide turn-key machine with technical data, tooling and accessories, delivery, unloading and rigging, installation, testing and on-site operator, maintenance, electrical, and mechanical training. Potential sources must also remove of two (2) Motch VGC-52 grinders from the area. The result of this market research will contribute to determining the method of procurement. The applicable North American Industry Classification System (NAICS) code assigned to this procurement is 333517. THIS SOURCES SOUGHT IS FOR INFORMATION PURPOSES ONLY. THIS IS NOT A REQUEST FOR QUOTE/PROPOSAL. IT DOES NOT CONSTITUTE A SOLICITATION AND SHALL NOT BE CONSTRUED AS A COMMITMENT BY THE GOVERNMENT. RESPONSES IN ANY FORM ARE NOT OFFERS AND THE GOVERNMENT IS UNDER NO OBLIGATION TO AWARD A CONTRACT AS A RESULT OF THIS ANNOUNCEMENT. NO FUNDS ARE AVAILABLE TO PAY FOR PREPARATION OF RESPONSES TO THIS ANNOUNCEMENT. ANY INFORMATION SUBMITTED BY RESPONDENTS TO THIS TECHNICAL DESCRIPTION IS STRICTLY VOLUNTARY.�� Submission Instructions: Interested parties should submit a response to this Sources Sought Notice by December 30, 2022 NLT 04:00 pm EST. All responses under this Sources Sought Notice must be emailed to Ashley.Saunders@dla.mil. Responses should not exceed twenty five (25) one-sided 8.5 x 10 inch pages with a font that is no smaller than 10 point as this is not a request for a proposal but only a request for submission of a vendor's capability to perform this requirement. Telephone inquiries will not be accepted or acknowledged, and no feedback or evaluations will be provided to companies regarding their submissions. DLA Aviation intends to issue a request for proposal for two CNC Vertical Grinding Machines, including: removal of two (2) Motch VGC-52 grinders from the area technical data, tooling and accessories, delivery, unloading and rigging, installation, testing and on site operator, maintenance, electrical, and mechanical training. Interested parties may identify their interest and capability to respond to this requirement no later than the stated closing date/time. Place of performance is Feet Readiness Center, Jacksonville DLA Aviation is requesting industry input into the feasibility of the government�s requirements. In your response, please provide: Description of your company�s capabilities, based on the questions below Comments on the attached statement of work. Please identify on the attached statement of work if your company is capable of providing the requirement as written or propose an alternative solution. Please identify your company�s business size in terms of number of employees, and whether domestic or foreign for consideration of solicitation set-aside, and small business subcontracting requirements. Please identify your company�s manufacturer status: Manufacturer/Non-Manufacturing Source. If non-manufacturing source, please identify the manufacturer. Please identify whether your company will partner with subcontractors to complete this requirement. Please provide a basis of estimate to consider the total financial budget of this requirement. Estimates should capture the total procurement requirements, not solely the machine�s requirements.� Physical Characteristics: The attached purchase description outlines the physical characteristics of the machine to include: Each machine must fit within the allowable floor plan per machine of 24 feet x 14 feet x 15 feet ( L x W x H) There is an existing 12 feet x 12 feet foundation. 1 per machine.� The machines are to be integrated to these foundations.� Please identify each machines� overall footprint and the ability of the machine to integrate the existing 12 feet x 12 feet foundation Refer to paragraphs: 3.3.1 Base to 3.3.15 Electrical System and 3.3.18 Motors to 3.3.21 Hour Meter. Please comment on the draft purchase description of whether the current physical characteristics are achievable, or whether the Government should consider an alternative that is commercially available. System safety, design, and engineering requirements are to be supported by industry standards.�� Since this is a government industrial facility, the current standards used are documented within the specification.�� The government may allow for a substitute standard after comparison with the command�s safety office.�� Not all substitutes will be permitted or granted.� Detailed below are the currently used standards for the FRCSE facility.� Please identify if you can comply with the standards referenced or what alternate would be proposed for use in lieu of.�� Current standards for safety are as follows: Overarching safety and health for any component not specifically referenced will comply to OSHA, 29 CFR 1910.� Each machine will have work light complying with NFPA 79 requirements Electrical connections made to the facility must conform to NFPA 70 Safety Guarding per ANSI B11 Work platform meeting OSHA 29 CFR 1910 Electrical systems and electrical enclosure meeting NEMA ICS 6, NEMA 250 type 12, and NFPA 79.� Arc flash protection signage per NFPA 79 Motors to meet the requirements of NEMA MG-1 Pneumatic system conforms to ISO 4413 Hydraulic system conforms to ISO 4414 Functional Characteristics: FRCSE requires the capability to utilize the grinding actions at an angle, with the ability to manipulate the tooling or grinding wheel to a given angle in very price increments.� The angular grinding is needed for contour grinding which is best suited for complex geometry parts. Please detail your company�s method to achieve this requirement. Please specify whether your company�s machine needs a �B-Axis� to accomplish this mission. If �no� please explain how your company�s machine operates to grind at an angle. In your response, please identify the output time achievable through your machine�s methodology. Additional functional characteristics are outlined in the attached purchase description. Refer to paragraphs: 3.3.2.3 B Axis (Spindle Swivel) and 3.3.16 3.3.16����� Computer Numerical Control (CNC) Features to 3.3.17 Computer System. �Please comment on the draft purchase description of whether the current functional characteristics are achievable, or whether the Government should consider an alternative that is commercially available. Performance Characteristics: Please identify your company�s minimum diameter rotary table and drive, defined as the �C-Axis�. Is your company capable of meeting minimum 60-inch diameter rotary table and drive, defined as the C-Axis? Please identify all materials your company�s machine is capable of grinding. Is your company�s machine capable of grinding: carbide, tool steel, high speed steel, tungsten, nickel chrome, and titanium? Additional performance characteristics are outlined in the attached purchase description. Refer to paragraphs: 3.4 Size and Capacity and 3.5 and Alignment and Accuracy Tolerances.� Please comment on the draft purchase description of whether the current performance characteristics are achievable, or whether the Government should consider an alternative that is commercially available. Additional scope requirements: Please review the additional scope requirements as follows: Tooling Needs, Paragraph 3.6 Standard Tooling and Equipment Equipment Identification and Markings, Paragraph 3.7, Marking on Instruments, Control Panels, and Plates.� Technical Data and Planning, Paragraph 3.8, Technical Data Installation of new equipment and removal of existing Motch VGC-52 Grinders, Paragraph 3.9, Installation Operator and Maintenance Training, Paragraph 3.10, Training Acceptance testing is conducted at governments facility with the cited test procedures, as referenced in paragraph 4.7.4, Performance Test Destination. ��Please comment on feasibility of tests along with your company�s ability to execute the test.� Please provided feedback on the applicability and feasibility of the government directed test.� Please comment on the draft purchase description of whether the current performance characteristics are achievable, or whether the Government should consider an alternative that is commercially available.
- Web Link
-
SAM.gov Permalink
(https://sam.gov/opp/fb16bdfd8e064e9ca437e419225a0a29/view)
- Place of Performance
- Address: Jacksonville, FL, USA
- Country: USA
- Country: USA
- Record
- SN06539467-F 20221210/221208230106 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |