SAMDaily.us | PRESOL | C | H&H SATOC Architect & Engineering Services

SAMDAILY.US - ISSUE OF MARCH 15, 2023 SAM #7778
SOLICITATION NOTICE

C -- H&H SATOC Architect & Engineering Services

Notice Date: 3/13/2023 1:43:14 PM
Notice Type: Solicitation
NAICS: 541330 — Engineering Services
Contracting Office: US ARMY ENGINEER DISTRICT PORTLAND PORTLAND OR 97204-3495 USA
ZIP Code: 97204-3495
Solicitation Number: W9127N23R0014
Response Due: 3/27/2023 1:00:00 PM
Archive Date: 04/11/2023
Point of Contact: Andrew Sprys, Phone: 5038084616, Andrea Smothers
E-Mail Address: andrew.j.sprys@usace.army.mil, andrea.k.smothers@usace.army.mil
(andrew.j.sprys@usace.army.mil, andrea.k.smothers@usace.army.mil)
Description: SYNOPSIS �for INDEFINITE DELIVERY CONTRACT FOR HYDRAULIC AND HYDROLOGY ENGINEERING SERVICES FOR THE USACE PORTLAND DISTRICT General Information Document Type:�� Synopsis/ Solicitation Notice Solicitation Number:� �� W9127N23R0014 A0004 Synopsis Posted Date:� �� February 2, 2023 Original Response Date:� � �� March 6, 2023 Current Response Date:� �� March 27, 2023 Archive Date:� �� April 11, 2023 Classification Code:� �� C � Architect and Engineering Services NAICS Code:� �� 541330 � Architect & Engineering Services Contracting Office Address The U.S. Army Corps of Engineers (USACE), Portland District 333 SW First Ave., Portland, OR 97204 1.� CONTRACT INFORMATION.� The resulting contract will be an Architect-Engineer (A-E) Indefinite Delivery Indefinite Quantity (IDIQ), firm-fixed-price contract for Hydraulic and Hydrologic Engineering Services. This IDIQ contract is being procured in accordance with the Architect and Engineering Selection Statute (formerly the Brooks Act) as implemented in FAR Subpart 36.6. Firms will be selected for negotiation based on demonstrated competence and qualifications outlined in Federal Acquisition Regulation (FAR) 36.602-1 and DFARS 236.602-1 for the required work. This synopsis will facilitate the award of one contract with capacity of $10 million and a duration of five years starting from the award date.� North American Industrial Classification System Code (NAICS) is 541330, which has a size standard of $25.5 million or less in average annual receipts over the last 3 years.� The wages and benefits of listed services employees (see FAR 22.10) performing under this contract must be at least equal to those determined by the Department of Labor under the Service Contract Act under http://www.wdol.gov, as determined relative to the employee�s office location (not the location of the work).� To be eligible for contract award, a firm must be registered in the Department of Defense (DOD) System for Award Management (SAM).� Register via the SAM Internet Site at https://www.sam.gov or by contacting the Service Desk at 1-866-606-8220. THIS NEW ANNOUNCEMENT IS UNRESTRICTED AND IS OPEN TO ALL BUSINESSES REGARDLESS OF SIZE. If a large business is selected for this contract, it must comply with FAR 52.219-9 regarding the requirement for a subcontracting plan on that part of the work it intends to subcontract. The subcontracting plan is not required with this submittal but will be required with the fee proposal of the firm selected for negotiations.� This information is provided to help you in the development of your team. The contract awarded under this announcement will be administered by the U.S. Army Corps of Engineers, Portland District.� The Portland District may elect to transfer capacity to the Seattle, WA, or Walla-Walla, WA, Omaha, NB or Kansas City, MO, districts. 2.� PROJECT INFORMATION.� A-E hydraulic and hydrologic engineering services for the evaluation, analysis, and design of water resources civil works projects including but not limited to dams, levees, jetties, rivers, estuaries, and other facilities is needed.� The contractor will provide all equipment required to support the following additional services: sediment sampling/Hydro survey, LiDAR and Sonar.� The location of work performed under this contract shall be stated in the individual Task Orders; however, the Government expects the bulk of the Task Orders to be issued by the Portland District (CENWP).� Typical services include: Hydraulic and Coastal Design. Hydraulic design of juvenile and adult fish facilities, high and low head dam facilities, and navigation facilities. Planning, application, and interpretation of physical model studies to include hydraulic design of fish passage and hydraulic structures. Performance of physical sediment and coastal models and wave flume studies. Development of numerical (1-D, 2-D, and 3-D) models of hydraulic, coastal, and estuarine structures and environments. Development of physical models (general and sectional) of hydraulic, coastal, and estuarine structures and environments. Procurement and interpretation of hydroacoustic data from stilling basins, reservoirs, streams, federal navigation channels, fishways, and submarine structures for model development and condition assessment including difficult acoustic conditions such as shallow concrete channels with perpendicular surfaces, swift water, and limited GPS visibility. Planning, execution, interpretation, and reporting of prototype testing and data collection programs including use of instrumentation such as Acoustic Doppler Current Profilers (ADCP) and Acoustic Doppler Velocimeters (ADV), data processing methods, and interpretation of river velocities and flows around structures. Coastal Engineering development and analyses of coastal processes (both incident to projects and within project areas), determination of applicable wave and water level climate, calculation of wave forces, overtopping and wave transmission, wind setup and wave run-up, coastal engineering design of shore protection and navigation structures, and analysis of both hydraulic and sedimentation processes. Hardware and software to build, develop and execute computational fluid dynamic (CFD) models using Star CCM+ and other CFD programs. Development of CFD model geometry and grids using state-of-the-art geometry development and grid generation software to present numerical and physical modeling results in visualization software (such as TecPlot, FieldView, or similar programs). Use of Coastal Engineering Programs including ADCIRC, STWAVE, CGWAVE, and BOUSSS2D. Reservoir Regulation, Water and Sediment Quality (In Conjunction with Engineering Services).� Reservoir analyses including flood control and conservation, flood warning systems, system analyses, Endangered Species Act (ESA) flow issues, water control manuals, real-time operational studies (runoff, flood, etc.), and real-time reservoir management for flood control. Water quality characterization (physical, chemical, and biological), data collection, and reporting of estuarine and freshwater systems. Calibration, deployment, and maintenance of continuous multi-parameter water quality probes and meteorology equipment for long-term deployment. Collection of depth profile of field parameters and grab samples in reservoirs. Laboratory analysis for nutrients and other chemical parameters using standard methods. Phytoplankton and zooplankton species identification and enumeration. Laboratory analysis of cyano-toxins. Evaluate and display data to support analysis to determine sources of water quality impairments and the status/trends of water quality. Water Quality modeling of reservoirs, rivers and estuaries using programs such as CE-QUAL-W2 (COE 2D reservoir/river model), WESTEX (COE 1D reservoir temperature model), QUAL2E (EPA 1D, steady state river model), and MIKE11 (DHI 1D dynamic river model). Water quality and sediment quality database products including AQUARIUS and Environmental Information Management (EIM). Laboratory Accreditation - IAW National Environmental Laboratory Accreditation Conference (NELAC) accredited laboratory for water quality and sediment sample analysis. Contract laboratories shall meet the minimum laboratory Quality Assurance/Quality Control, technical, and management requirements provided in the July 2013 Department of Defense and Department of Energy Consolidated Quality System Manual for Environmental Laboratories, Version 5.0 (or more recent version), available at: http://www.denix.osd.mil/edqw/upload/QSM-DOD-DRAFT-FINAL-052313.pdf. �Sediment samples shall be analyzed in accordance with methods prescribed in the 2009 SEF. River and Hydrologic Engineering.� Statistical and probability analyses, discharge, precipitation, and risk and uncertainty evaluations; hypothetical storm development, period-of-record evaluations, ungaged basin evaluations, rainfall � runoff analyses, Probable Maximum Precipitation (PMP), snowmelt, hydrographs, Probable Maximum Flood (PMF) and spillway design hydrograph development. Channel design, channel morphology, ecosystem restoration/channel restoration, process based channel design, bank protection, riprap sizing, and river training structures (groins, pile dikes, etc.). Development of numerical (1-D and 2-D) models of river and estuarine structures and environments. Planning, application, and interpretation of numerical model studies for hydraulic investigations such as floodplain management studies/flood insurance studies, habitat restoration projects, and sediment transport. Evaluation of climate scenarios and use of Global Climate Models (GCM) as specified in the Intergovernmental Panel on Climate Change AR5. Familiarity with working with spatially distributed hydrologic modeling systems that are able to take outputs from GCMs. Use of River and Hydrologic programs including� HEC-HMS, HEC-GeoHMS, HEC-RAS, HEC-GeoRAS, HEC-FFA, HEC-FDA, HEC-FIA, HEC-SSP, HEC-EFM, HEC-ResSim, and HEC- DSSVue, HEC-FFA, ADCIRC, and AdH. Use of Geographic Information Systems Programs including ArcGIS. Physical Model Capability.� Evaluation shall consider physical model facilities and model data collection equipment and capabilities. Square-footage of physical model laboratory. Hydraulic capacity of the physical model laboratory. Ability and capability of simulating waves and wave patterns for coastal and estuarine structures. Location of physical model facility. Model data collection equipment available to measure water depth, water surface elevations, water velocity, and volumetric flow rates, including the capability to data-log any of those variables over time. Work Incidental to A-E Efforts. The following work may be required in conjunction with but will only be incidental to A-E efforts. Procurement of sediment samples using various surface grab and core sampling devices such as Van Veen, PONAR, box core, gravity core or vibracore, in both deep and shallow water bodies. Physical and chemical analysis of sediment may include grain-size gradation, American Society of Testing and Materials (ASTM) dredge parameters, and chemicals of concern as described in the 2009 SEF. Biological analysis related to sediment quality including bioaccumulation studies and/or bioassays in conjunction with sediment chemical analysis. Biological site characterization may include benthic sampling and analysis, epibenthic invertebrate and fish collection and identification, crab pot deployment and retrieval, marine plant and animal community analysis, sediment profile imaging, and multibeam bathymetric surveys. Hydrographic (single-beam and multi-beam sonar) and topographic (land survey, photogrammetry, and/or LiDAR) surveys to support modeling. Sediment characterization (physical, chemical, and biological), data collection, and reporting for marine, estuarine, and fresh water systems including use of the 2009 Sediment Evaluation Framework (SEF) for the Pacific Northwest, which is the regional sediment evaluation manual used in the states of Oregon, Washington, and Idaho. Analysis of tidal wetlands in estuary environments that can support ecosystem restoration design. Familiarization of FEMA policies, analytical and mapping standards/requirements for flood hazard mapping partners and flood insurance studies. 3.� SELECTION CRITERIA.� Selection criteria for this contract will be based upon the following selection criteria, listed in descending order of importance (Criteria �a� through �e� are primary, criteria �f� and �g� are secondary, used only as a �tie-breaker� among technically equal firms. Primary Criteria: Specialized experience and technical competence in the type of work required, including, where appropriate, experience in energy conservation, pollution prevention, waste reduction, and the use of recovered materials. The firm must demonstrate specialized experience and technical competence in the following areas: Hydraulic, Hydrologic and Environmental Engineering analysis and design in the areas of structural, fluvial and dam hydraulics Hydrology, river engineering and sedimentation Coastal engineering specific to Pacific Northwest Reservoir systems analysis Sediment characterization: physical, chemical and biological Channel morphology To be considered, experience must have been performed within the last six (6) years. The Government will review ten (10) completed projects and involvement in the completed projects for whether the firm has specialized experiences and technical competence in the relevant areas outlined below in section 3.� If a prime A-E firm is using a subcontractor's experience, the prime A-E firm shall submit letters of commitment from those subcontractors and any key personnel employed by those subcontractors.� Firms shall provide examples of one to three (1 to 3) projects performed by either the prime A-E firm or a key subcontractor demonstrating their experience in the following types of services as it relates to the Project Information described in paragraph 2 above. Submittals that demonstrate having more of the experiences listed below above will be rated as more technically relevant. Professional qualifications necessary for satisfactory performance of required services. Professional qualifications (FAR 36.602-1(a)(1)). The board will evaluate the firm�s professional qualifications including education, registration, technical certification, training, and longevity of relevant experience of the Key Personnel in relation to their role on the project. Firms shall provide a minimum of one (1), but no more than two (2), resumes for each Key Personnel position, identified below. If providing additional resumes beyond the number requested for each key personnel, the board will review the maximum number in the order presented in the SF330. The board will not evaluate the other resumes. Do not generalize professional registrations or certifications; provide specific details. All disciplines, except those specifically noted, require an applicable professional license, registration, or certification. For the purpose of this criterion, a foreign license, registration, or certification is not applicable. The education, training, professional registration, proposed job title, and overall relevant experience of key personnel will be considered. The board shall consider experience relevant if similar to the specialized experience described in Criterion 3a. Where proposing more than one individual (resume) for any discipline, the board shall consider the cumulative qualifications of all resumes within that discipline. An individual can only support one discipline (i.e., an individual cannot submit resumes for multiple disciplines). This criterion is primarily concerned with the qualifications of the key personnel identified by the A-E and not the number of personnel, which is under Criterion D - Capacity. Submit resumes in Section E of the SF330 for each of the Key Personnel in the disciplines below (listed in descending order of importance): Project Managers(s), Geotechnical Engineer(s) (GE), Engineering Geologist(s) (PEG), and Geologist(s) (PG, PEG) Project Managers, Hydraulic Engineers, Hydrologist/Hydrologic Engineers, Coastal Engineers, CADD Technicians, Land Surveyors (PLS), GIS Analysts, Biologists, Toxicologists, and Geomorphologists. Additional considerations: The Government evaluates more favorably key personnel that worked on the example projects in Section A. The Government may evaluate key personnel employed by the Prime/JV more favorably. The basis of the evaluation will be the information in Sections E, G, and H of the SF330. Past performance on contracts with Government agencies and private industry in terms of cost control, quality of work, and compliance with performance schedules.� Relevant Past Performance on contracts with Government agencies and private industry over the past six (6) years will be evaluated in terms of cost control, quality of work, and compliance with performance schedules. �The Government will review information contained within the DoD A-E Contractor Performance Assessment Reporting System (CPARS) in order to determine each firm�s performance on relevant contracts.� The Government will also evaluate other Federal, State, and/or private past performance information provided by the Contractor.� For consideration of past performance from other federal, state, and private information, the Contractor shall provide reference information to include project name, point of contact, current phone number and email address.� Also include any ratings, letters of appreciation, awards, etc., for relevant experience. Capacity to accomplish the work in the required time.� Explain or demonstrate how your firm has the capabilities to perform up to 3 concurrent task orders with a value of $250,000 each in 120-days in accordance with Federal Acquisition Regulation (FAR) 15.408(n)(2) in regards to limitations on pass-through charges. FAR website link -> https://www.acquisition.gov/ Knowledge of the locality of the project.� The firm will be evaluated for its knowledge and experience with hydraulic modeling and prototype testing studies for design of migrant fish facilities, high head dam facilities, and navigation facilities specifically within Oregon and Southwestern Washington waterways, including the Pacific Ocean.� The firm shall also be evaluated for its knowledge and experience with Pacific Northwest Meteorology (climate and weather), water quality, geography, and geology as the affect hydrologic, geomorphic, and design parameters for water resource evaluation and design. Secondary Criteria: Small Business Participation: Extent of participation of small businesses (including women-owned), small disadvantaged businesses, historically black colleges and universities, and minority institutions in the proposed contract team, measured as a percentage of the total estimated effort. Demonstrate use of small business sub-contractors on past projects. Geographic Proximity: Location of the firm in the general geographical area of Oregon and Southwest Washington. Equitable Distribution of DoD Contracts. Volume of DoD A-E contract awards in the last 12 months, with the objective of effecting an equitable distribution of DoD A-E contracts among qualified firms shall be evaluated and used in the event of a tie. 4. Interested firms having the capabilities to perform this work must submit one pdf copy of the SF 330 Part I and required attachments via email to Andrew Sprys, Contract Specialist, at Andrew.J.Sprys@usace.army.mil and Andrea Smothers, Contracting Officer, Andrea.K.Smothers@usace.army.mil at no later than 1:00 PM on 27 March 2023. This is not a request for proposal. This procurement is open to all businesses regardless of size under the NAICS Code 541330. The small business size standard is $25.5 million.� All responses must be received by the specified due date and time to be considered. Any responses received after that date and time will not be considered. Point of Contact for small business questions or assistance is the Portland District Deputy for Small Business, Carol McIntyre at 503-808-4602 or Carol.A.Mcintyre@usace.army.mil. Additional information on how to prepare an A&E submittal can be found in Engineering Pamphlet (EP) 715-1-4 � Competing for Architect-Engineer Contracts Awarded by the U.S. Army Corps of Engineers (9/30/2004) USACE publications website:� www.publications.usace.army.mil. Questions and Inquiries about this Synopsis All inquiries regarding this synopsis will be submitted via ProjNet-BidSM.� Telephone and email inquiries will not be accepted. ProjNet-BidSM is a web-based program that allows submitters to post questions regarding the synopsis and to view all questions by other submitters and answers by USACE. ProjNet-BidSM can be accessed through ProjNetSM at https://www.projnet.org/projnet/. To access the ProjNet-BidSM website the first time: Click the Bid tab Click Bidder Inquiry. (The Agency is USACE.) Enter the following information for access: The Bidder Inquiry Key: �39K8F9-S9V8AR Valid business contact information (e.g. Company name, contact person, business address, phone number and email address). (required on first project only) Establish secret question and answer which will be used as a password. (Required on first project only). For subsequent access use your email address, the Bid Inquiry Key and response to the secret question to access the ProjNet-BidSM Module. Submit questions or review questions and answers. A firm who submits a question will receive an automated email notification that their question has been received. When an answer is posted to a question, the question and answer is then available for all other bidders to review. For a specific step-by-step for POSTING YOUR INQUIRIES, is available in the Reference link on the Contract Viewer. For questions about the ProjNet-BidSM, please contact the Call Center help desk toll free at 1-800-428-HELP, which operates from 8AM to 5PM (Central US time zone). ProjNet-BidSM questions can also be emailed to the helpdesk at staff@rcesupport.com. The cutoff for questions and inquires is 22 March 2023. All submitters are responsible for reviewing the questions and responses in ProjNet-BidSM prior to their submission. Nothing in the synopsis is changed unless an amendment is posted on https://sam.gov/content/home Amendment 0004 � Due to network connectivity and system issues the solicitation is being extended until 27 March. Firms are encourage to confirm receipt of their proposals and submit any questions to both ProjNet-Bid and to Andrea Smothers at andrea.k.smothers@usace.army.mil and Andrew Sprys at andrew.j.sprys@usace.army.mil�
Web Link: SAM.gov Permalink
(https://sam.gov/opp/f1a54b71201d4f04b6e2de8011f34796/view)
Place of Performance: Address: Portland, OR 97204, USA; Zip Code: 97204; Country: USA
Record: SN06615853-F 20230315/230313230106 (samdaily.us)
Source: SAM.gov Link to This Notice
(may not be valid after Archive Date)

| FSG Index | This Issue's Index | Today's SAM Daily Index Page |

Loren Data's SAM Daily™

C -- H&H SATOC Architect & Engineering Services