SOLICITATION NOTICE
53 -- SCREW HEX HEAD
- Notice Date
- 4/27/2023 5:56:07 AM
- Notice Type
- Presolicitation
- NAICS
- 332722
— Bolt, Nut, Screw, Rivet, and Washer Manufacturing
- Contracting Office
- DLA MARITIME - NORFOLK PORTSMOUTH VA 23709-5000 USA
- ZIP Code
- 23709-5000
- Solicitation Number
- SPMYM123Q0049
- Response Due
- 4/27/2023 6:00:00 AM
- Archive Date
- 04/28/2023
- Point of Contact
- LAKEISHA VIOLENUSELLIS, Phone: 7572785101
- E-Mail Address
-
lakeisha.violenusellis@dla.mil
(lakeisha.violenusellis@dla.mil)
- Small Business Set-Aside
- SBA Total Small Business Set-Aside (FAR 19.5)
- Description
- SYNOPSIS: The Defense Logistics Agency (DLA) Maritime Norfolk at Norfolk Naval Shipyard (NNSY) intends to award a Firm Fixed Price (FFP) Single Award Contract for the items listed below. The required items are for commercial items prepared in accordance with the information in FAR Part 13 and FAR Subpart 12.6, as supplemented with the additional information included in this notice. The Contract Line Items (CLINs) are as follows: CLIN 0001 QTY 9 EA SCREW HEX HEAD 1-1/2-6 UNC-2A X 7.250 QQ-N-286 REV. G K500 MONEL SPECIAL HEX HEAD SHOULDER SCREW, ANNEALED & AGE HARDENED, WITH 1.748-1.750 BODY DIAMETER, PER SKETCH BELOW. MARK TOP OF HEAD WITH MFG ID, LOT# & .K. GRADE SYMBOL. ORDERING DATA: A)���� NICKEL-COPPER-ALUMINUM ALLOY, WROUGHT (UNS N05500); QQ-N-286G; 07 DECEMBER 2000 B)���� FORM 2; COLD DRAWN C)���� N/A D)���� N/A E)���� 1-1/2-6 UNC-2A X 7.250 F-S) N/A T) PER 5.1 OQE Ordering Requirements for CIM Provide written verification that the chemical and mechanical properties have been determined and are acceptable IAW the required specification QQ-N-286 as applicable for Document# 3076C028 are as: a.) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing. b.) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided. In the case of a finished product identified by a lot number manufactured from a start material identified by a heat number, the final test reports performed on the finished product samples shall be marked with the lot number. The test reports for the raw material shall be marked with the heat number of that material. c.) Test reports labeled ""Typical,"" those with words such as ""to the best of our knowledge"" or ""we believe the information contained herein is true"" or those that have results transcribed from other reports or documents, or test reports with the heat/lot/batch number information handwritten on them are not acceptable. d.) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222 K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed (i.e., fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process. e) Certifications for QQ-N-286 Rev G materials shall show that slow strain rate tensile {SSRT} test of ""start material"" has been accomplished per QQ-N-286 Rev G requirements. f.) Where headed fastener specifications require a yield strength test AND a wedge tensile test, a separate (new, untested) fastener is required for each of the two test methods, and both of these tests shall be reported. NOTE: This does not apply to steel hex head fasteners (grades 2, 5, 8, B7, and B16) are certified to a proofload and NOT yield strength; therefore, this issue does NOT apply to those fasteners. NOTE: This does apply to All CRES and non-ferrous bolts and screws, and ALL steel socket head cap screws (grade A574 and 4340). Wedge tensile test a required test for including ones that had their yield strength and tensile strength certified by alternative testing IA W MIL-DTL-1222. The requirement will be solicited as a total small business set aside. The NAICS code applicable to this procurement is 332722: Bolt, Nut, Screw, Rivet, and Washer Manufacturing with a size standard of 500. The Product Service Code is 5305, Screws. The anticipated delivery date for this acquisition is 15 days ARO after contract award. The solicitation, any documents related to this procurement, and all amendments issued will be in electronic form only. THE SOLICITATION IS NOT YET AVAILABLE. The solicitation number is SPMYM123Q0049 and it is expected to be available on or about 27 APR 2023 and posted to SAM.gov, https://sam.gov/� Quotes will be due by 5:00 PM EST on 4 MAY 2023. Responses to the solicitation notice shall be emailed to the attention of LaKeisha Violenusellis at lakeisha.violenusellis@dla.mil. �Please make sure that the solicitation number (SPMYM123Q0049) is included in the subject line of any email correspondence. Emails without subject lines will not be read because of security issues. Potential offerors are hereby notified that the solicitation and any subsequent amendments will only be available by downloading the documents at www.SAM.gov (Contracting Opportunities). The Government is not responsible for inability of the Offeror's to access solicitation documents posted. No telephone or FAX requests will be accepted, and no hardcopy solicitation/amendment will be mailed or faxed. All responsible sources may submit a proposal which may be considered by the Government. By submitting an offer, the offeror will be self-certifying that neither the principal corporate officials nor owners are currently suspended, debarred, or otherwise ineligible to receive contracts from any federal agency. Failure to do so may represent grounds for refusing to accept the proposal. By submission of a proposal, the offeror acknowledges the requirement that a prospective awardee must be registered in the System for Award Management (SAM) database prior to award, during performance, and through final payment of any contract resulting from the solicitation, except for awards to foreign vendors for work to be performed outside the United States. Lack of registration in the SAM database will make an offeror ineligible for award. Offerors may obtain information on registration and annual confirmation requirements by calling 1-866-606-8220, or via the Internet at https://www.sam.gov. All questions shall be submitted in accordance with the solicitation, dates and procedures. Please direct all questions regarding this requirement to LaKeisha Violenusellis at lakeisha.violenusellis@dla.mil.
- Web Link
-
SAM.gov Permalink
(https://sam.gov/opp/be16d8a44de942508851ad88964e7426/view)
- Place of Performance
- Address: Portsmouth, VA 23709, USA
- Zip Code: 23709
- Country: USA
- Zip Code: 23709
- Record
- SN06664915-F 20230429/230427230109 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |