SOURCES SOUGHT
51 -- Flange Ball Bearing Auxiliary Power Unit Puller
- Notice Date
- 10/31/2023 7:03:40 AM
- Notice Type
- Sources Sought
- NAICS
- 332216
— Saw Blade and Handtool Manufacturing
- Contracting Office
- NAVAIR WARFARE CTR AIRCRAFT DIV JOINT BASE MDL NJ 08733 USA
- ZIP Code
- 08733
- Solicitation Number
- N6833524RFI0001
- Response Due
- 11/7/2023 1:30:00 PM
- Archive Date
- 11/22/2023
- Point of Contact
- Theresa A. T. Mason, Phone: 2405871133
- E-Mail Address
-
theresa.a.mason15.civ@us.navy.mil
(theresa.a.mason15.civ@us.navy.mil)
- Description
- *** Edited with confirmed PSC as 5120 and extended 7 days from reposted date for responses. PURSUANT TO FAR 15.201(e) - THIS IS A REQUEST FOR INFORMATION (RFI) ONLY. This RFI is issued solely for information and planning purposes � it does not constitute a Request for Proposal (RFP) or a promise to issue an RFP in the future. This request for information does not commit the Government to contract for any supply or service whatsoever. Further, the Government is not at this time seeking proposals and will not accept unsolicited proposals. Responders are advised that the U.S. Government will not pay for any information or administrative costs incurred in response to this RFI; all costs associated with responding to this RFI will be solely at the interested party�s expense. Interested parties are responsible for adequately marking proprietary or competition sensitive information contained in their response. Proprietary information will be safeguarded in accordance with the�applicable Government regulations. Failure to respond to this RFI does not preclude participation in any future associated RFP that may be issued. PURPOSE Naval Air Systems Command (NAVAIR), Naval Air Warfare Center, Aircraft Division, Lakehurst NJ (NAWCADLKE) is soliciting information and comments from industry on its ability to provide a Flange Ball Bearing Auxilary Power Unit (APU) Puller used Ashore and Afloat for V-22 aircraft. DEFINITION / DESCRIPTION The Flange Ball Bearing Puller should meet the requirement to install and/or disassemble the thrust ball bearing in the air inlet hoursing assembly. The Flange Ball Bearing APU Puller is used ashore and afloat, it is needed to raise the outer race of the flanged ball bearing in the air inlet housing assembly so all the bearing balls can drop into place during installation. Also, a mechanical puller is needed to pull the flanged outer race of the ball bearing from air inlet housing assembly during disassembly. NAWCADLKE is seeking information for industry regarding Flange Ball Bearing APU Puller. Please provide the following information about Flange Ball Bearing APU Puller. 1. General description of your Flange Ball Bearing APU Puller 2. Identification of critical requirements for the Flange Ball Bearing APU Puller 3. Overview of your Flange Ball Bearing APU Puller concept of operation 4. Discuss critical information required for the use of your Flange Ball Bearing APU Puller. 5. Describe environmental testing test methods 6. Provide any additional information you desire GENERAL GUIDELINES Your information package should not exceed 5 pages. Any operation manual provided shall not be counted against this page limit. Responses to this RFI should be submitted to Lakehurst Procurement via e-mail to theresa.a.mason15.civ@us.navy.mil no later than 8 business days from the date of this posting. Responses to this RFI will not be returned. Respondents will not be notified of the result of the review. If a solicitation is released, it may be synopsized on the SAM.gov. It is the potential vendor�s responsibility to monitor this site for the release of any follow-on information.
- Web Link
-
SAM.gov Permalink
(https://sam.gov/opp/b72e06eafdd2451f9e938d89be2173fc/view)
- Record
- SN06872671-F 20231102/231031230053 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |