SOLICITATION NOTICE
59 -- New BeCu Machined Part Production
- Notice Date
- 12/20/2024 1:25:21 PM
- Notice Type
- Combined Synopsis/Solicitation
- NAICS
- 334290
— Other Communications Equipment Manufacturing
- Contracting Office
- NUWC DIV NEWPORT NEWPORT RI 02841-1703 USA
- ZIP Code
- 02841-1703
- Solicitation Number
- N6660425Q0101
- Response Due
- 1/3/2025 11:00:00 AM
- Archive Date
- 01/18/2025
- Point of Contact
- John Paul McCauley, Phone: 4018322126
- E-Mail Address
-
john-paul.mccauley.civ@us.navy.mil
(john-paul.mccauley.civ@us.navy.mil)
- Small Business Set-Aside
- SBA Total Small Business Set-Aside (FAR 19.5)
- Description
- INITIAL POST: See attached combined synopsis/solicitation PDF. ---------------------------------------------------------------------------- AMENDMENT 1: The purpose of this amendment is to: 1. Extend the closing date of the combined synopsis/solicitation from 2 December 2024 to 13 December 2024; 2. Answer industry questions. Industry questions: Q1. The CDRLs call out a First Article Acceptance Test Report (FAAT). The drawings are only for machined parts, not a full FBG Assembly. Will a full FBG Assembly need to be assembled with other GFM? a. The individual machined piece part will not need to be assembled with other GFM. Q2. If there is a FAAT Report, is there a Test Procedure that will be provided? a. For FAAT qualification of the individual piece part, the vendor shall provide a full Coordinate-Measuring Machine (CMM) data, Material Conformance Certification in accordance with Note 5 of each drawing. The CMM data along with the Material Conformance Certification will give the Government the necessary technical information to qualify the machined part would meet the FAAT qualifications when assembled at the higher-level assembly. ---------------------------------------------------------------------------- AMENDMENT 2: The purpose of this amendment is to answer industry questions. Q1. Does NAVSEA have models for all Part Nos. within the RFQ? a. Yes, NAVSEA has models for all part numbers within the RFQ. Q2. Do vendors for Special Processes have to been NADCAP certified? (ie, Nickel-plating, etc.) a. Negative. ---------------------------------------------------------------------------- AMENDMENT 3: The purpose of this amendment is to answer industry questions and extend the closing date of the combined synopsis/solicitation from 13 December 2024 to 27 December 2024; Q1. The latest drawing calls out Rev C on page 1 and Rev B on page 2? a. This is a typographical error and the document should read ""Rev C"" on both pages. This error is non-impactful. All offerors will be or have been provided the same documentation which will enable quote provision. Q2. Will models be made available prior to award? a. Negative, models are not required in order to furnish a quote, but will be made available post-award. ---------------------------------------------------------------------------- AMENDMENT 4: The purpose of this amendment is to update the required quantities and extend the closing date of the combined synopsis/solicitation from 27 December 2024 to 3 January 2025. See ""N6660425Q0101_Updated Quantities Amendment 4"" document.
- Web Link
-
SAM.gov Permalink
(https://sam.gov/opp/ba34e2635f394b27bd9be0d0f25383a3/view)
- Place of Performance
- Address: Newport, RI 02841, USA
- Zip Code: 02841
- Country: USA
- Zip Code: 02841
- Record
- SN07299205-F 20241222/241220230116 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |