NAVAL AIR WARFARE CENTER AIRCRAFT DIVISION, INDIANAPOLIS, 6000 EAST 21ST STREET, INDIANAPOLIS, IN 46219-2189

36 -- LIQUID DISPENSING SYSTEM SOL N00163-95-R-0134 DUE 040695 POC Contact Point, THOM L. DOROTHY, (317)353-3748, Contracting Officer, ELBERT H. WILSON, (317)353-3748 The Naval Air Warfare Center, Aircraft Division, Indianapolis, (NAWC-ADI) intends to negotiate a sole source contract with CAMELOT SYSTEMS INC. of Haverhill, MA, for the purchase of one (1) each Liquid Dispensing System, installation, operator and maintenance training, and operations and maintenance manuals, all to be delivered, installed, and training within 120 days following award of contract. The Liquid Dispensing system shall include, but not be limited to the following salient characteristics: Programmable to place dispense locations within +/- .003 inch of True Position Radius of programmed x,y locations. Capable of maintaining a programmed x, y location repeatability of +/- .002 inches. LD adhesive dispenser with z axis height resolution and repeatability at least +/- .002 inches and a z axis travel of at least 4.5 inches. LD dispenser suitable for dispensing adhesvies such as Loctite chip bonder adhesvies 348, 368, 3603, 3609, epoxies, such as Ablestik 84-3T, and Spot Mask and solder paste. Dispenser head capable of dispensing 16,000 dots per hour. The LD System shall be capable to sense a Printed Wiring Board (PWB) height with a resolution and repeatability of +/- .0005 inches for each dispense location, and able to make corrections to the z programmed height. The LD System shall utilize standard EFD syringe sizes of either 3,5,10, 0r 30 milliliters. The LD System shall be capable of dispensing within 0.010 inches of a previous dispense location with out disturbance. The LD System shall be capable of dispensing lines, dots, arcs, circles, and perform an area fill routine. The speed of the LD System on the x, y, and z axis shall be programmable. A digitally controlled heated needle option, that heats the tip of the needle when activated, from room temperature up to 50 degrees centigrade shall be featured in the LD system.The LD System shall be able to step and repeat operations for multiple images on PWB's. A Transport system on the LD system shall be capable of handeling individual PWB's ranging in sizes from 2 X 2 inches up to 18 X 18 inches. Both single and double sided assemblies shall be able to be loaded onto the transport. The LD System transport shall have a programmable transport width that automatically opens to the programmed width. A LD system ''Teach Mode'' shall be capable of addressing : Needle Size, Dispense Location, Dispense Pattern, Machine to board offset values (HOME), amount of dispensing disposition, and type of dispense materials. The LD System Vision system shall be capable of recognizing fiducials of various sizes, shapes, using tooling holes of various sizes and various land patterns as fiducials. The LS System shall be equiped with a Dot Inspection system capable of measuring the accuracy of dispensed materials and reporting inconsistencies to the operator. On-Line daignostics testing for error conditions and signal displays are required for the LD System. Program CAD data in ASCII format either via ethernet or RS-232 port or through floppy drive is required. The LD systems shall have a buit-in seperate 486 based computer with 3 1/2 inch 1.44 MB, and a 170 MB harddrive as a minimum, with a 14 inch super VGA Monitor. Any responsible source may respond to this synopsis if qualified to provide ALL items identified above as salient characteristics, without deviation or substitutions. All responses must be in writing at the address listed above to the attention of Mr. THOM L. DOROTHY, or via FAX at 317-3563-3066, not later than 15 days following publication of this notice in the Commerce Business Daily. (CBD). (0044)

Loren Data Corp. http://www.ld.com (SYN# 0297 19950214\36-0001.SOL)