NASA, George C. Marshall Space Flight Center, Procurement Office, Marshall Space Flight Center, AL 35812

34 -- MILLING MACHINE AND ACCESSORIES SOL 8-P-5-06-72052 POC Contact Sherri Stroud, GP26H, 205-544-0329/Contract Specialist, or Teresa A. Foley, GP25G/Contracting Officer NASA/MSFC plans to issue a Request for Offer (RFO) for Milling Machine and Accessories as follows: Item 1 - Bridgeport series II milling machine, Catalog No 3157100C or equal with the following features: 2 Horse Power 2J head with R-8 taper, rectangular ways on saddle and knee, oval knee locks, power table feed variable from .75 to 35 I.P.M. acme 5 pitch, 1 5/8'' diameter lead screw for stability, 1500 lbs. capacity work table, minimum table size 11''x58'', table travel (X) 33.5, saddle travel (Y) 15'', quill travel 5'', knee travel (Z) 12'', ram travel 17'', throat distance 6'', table to spindle 4'', nose gauge lines 4'', variable speed low 60-500 rpm, high 500-4200 rpm, T-slot 5/8'', controlled downfeed range 0015, spindle diameter 1 7/8'', quill diameter 3 5/8'' height 83'' -- Qty 1 ea -- Item 2 - Drill set, 115-Piece, cobalt 3 in 1 jobber length with case, 1/16'' to 1/2'' x 64th, 1 to 60 and A to Z, Catalog No. CO-123H or equal -- Qty 1 set -- Item 3 - Drill set, 115 Piece, high speed steel, 3 in 1, jobber length with case, 1/16'' to 1/2'' x 64th, 1 to 60 and A to Z, Catalog No. S115E or equal -- Qty 1 set -- Item 4 - Cobalt steel 1/2'' shank, 13-Piece drill set with wooden stand, 17/32, 9/16, 19/32, 5/8, 21/32, 11/16, 23/32, 3/4, 13/16, 7/8, 15/16, 31/32 and 1'', Catalog No. S13CO or equal -- Qty 1 set -- Item 5 - High speed steel 1/2'' shank, 13 piece drill set with wooden stand, 17/32, 9/16, 19/32, 5/8, 21/32, 11/16, 23/32, 3/4, 13/16, 7/8, 15/16, 31/32 and 1'', Catalog No. S13HS or equal -- Qty 1 set -- Item 6 - High speed steel 1/2'' shank, 8-piece big boy set, with wooden stand, 1 1/16, 1 1/8, 1 3/16, 1 1/4, 1 5/16, 1 3/8, 1 7/16, and 1 1/2'', Catalog No S08 or equal -- Qty - 1 set -- Item 7 - Boring Head set, includes 1-DB1-203 Boring Head, 1-R-8 shank, 1-SBT-500D Boring Tool, 1-SBT-625D Boring Tool, 1-SBT-750D Boring Tool, 1-SBT-1000D Boring Tool, 1-SBT-1250D Boring Tool 1-10345 Boring Bar, 1-10390 Boring Bar and 1-12345 Boring Bar, Catalog No. 1400 or equal-- Qty 1 set -- Item 8 -- Carbide tipped, 14-Piece, Boring Bar set, Catalog No. CH-750 -- Qty 1 set -- Item 9 -- Internal Dial Caliper Gauge, range .375''-1.375'', Catalog No. IC-37 or equal -- Qty 1 ea -- Item 10 - Internal Dial Caliper Gauge, range 1.125''-2.125'', Catalog No. IC-112 or equal -- Qty 1 ea -- Item 11 - Internal Dial Caliper Gauge, range 1.875''-2.875'', Catalog No. IC-187 or equal -- Qty 1 ea -- Item 12 - Internal Dial Caliper Gauge, range 2.875''-3.875'', Catalog No. IC-287 or equal -- Qty 1 ea -- Item 13 - Internal Dial Caliper Gauge, range 3.625''-4.625'', Catalog No. IC-362 or equal -- Qty 1 ea -- Item 14 -- Telescoping Gauge set, 5/16''-6'', Catalog No. 290-100 or equal -- Qty 1 set -- Item 15 - V-block and clamp set, 2 1/2 x 2 3/4 x 2, capacity 2''round,, 1 7/8'' square, Catalog No. NVB-750-2 or equal --Qty 4 sets -- Item 16 - 6'' Diamond Wheel Tool Grinder, 1/2 Horse Power, 60HZ, 3600 idle RPM, reversing switch, 8'' 3 conductor card and plug, Catalog No. 522 or equal -- Qty 1 ea -- Item 17 - 6'' diameter Diamond Wheel, general purpose, Catalog No. D501 or equal -- Qty 2 ea -- Item 18 - 6'' diameter Diamond Wheel, fine finish, Catalog No. D502 or equal -- Qty 2 ea -- Item 19 Grinder Pedestal, 34 1/2'' high, Catalog No GA14 or equal -- Qty 1 ea -- Item 20 - 5C Hex and Square Collet block set, with hex and square block, lever collet closer and 2 nuts, cap 1/16'' to 1 1/16'', Catalog No ST5C or equal -- Qty 1 set -- NOTE: All referenced catalog numbers are Bridgeport Machines Inc or equal -- This procurement is being conducted under the NASA/MSFC MidRange Pilot Test Program approved by the Office of Federal Procurement Policy on April 16, 1993 -- Requests for copies of the RFO must be submitted in writing-- Transmission by facsimile to 205-544-9080 or by Internet e-mail to sherri.stroud@msfc.nasa.gov is acceptable -- RFO will be released on or about 15 days after publication in the Commerce Business Daily (CBD) -- Firm date for receipt of offers will be stated in the RFO -- This procurement is a total small business set-aside -- All responsible business sources may submit an offer which shall be considered by the agency -- Documents related to this procurement are available over the Internet -- The documents are in ASCII format and reside on a World-Wide Web (WWW) server, which may be accessed using client browsers, such as, MOSAIC -- The WWW address, or URL, of the MSFC Procurement home page is: ''http://procure.msfc.nasa.gov''. (0069)

Loren Data Corp. http://www.ld.com (SYN# 0199 19950313\34-0001.SOL)