Crane Division, Code 1165, Naval Surface Warfare Center, 300 Highway 361, Crane, IN 47522-5001

66 -- INSTRUMENTS AND LABORATORY EQUIPMENT SOL N00164-96-Q-0289 DUE 052496 POC Contact--Ms. Kathy King, Code 1165ZP, 812-854-3734, FAX 812-854-3465/Ms. Betty Gaiser, Contracting Officer This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. The solicitation number is N00164-96-Q-0289 and is issued as a Request for Quotation (RFQ). The quantity required for each item is two (2) each. Delivery is required within 14 days after effective date of award. Delivery shall be F.O.B. Destination to NSWC Crane IN with final inspection and acceptance at destination. Items are DX rated. The associated Standard Industrial Classification (SIC) code is 3826 and the small business size standard is 500 employees. This requirement is not reserved for small business. Other than Full and Open Competition will be used in accordance with FAR 6.302-1(a)(2), see Numbered Note 22. Discussions shall be conducted with Tucker Electronics Company, P.O. Box 551419, Dallas, TX 75355-1419. This is a requirement for various instruments which are listed as follows: (1) Programmable Power Source, Mfg. Fluke Mfg., P/N 4250A:3,6. Power source shall be capable of BCD or binary 2s complement coding. It shall have isolated control of an AC and DC external reference. It shall be capable of supplying up to 65V at 1 ampere. It shall have an accuracy of plus/minus 0.01% with resolution capability of 100 micro volts. It shall have a minimum response time of 30 to 110 micro seconds. It shall have an automatic output current limiter to a value between 10% and 110% of maximum in 10% steps and 1% steps to 11% of maximum output current. It shall have IEEE-488 interface capabilities. (2) Programmable Waveform Synthesizer, MFG. Wavetek Corp., P/N 178. The synthesizer shall have a minimum frequency bandwidth of 1 micro Hz to 50 MHz. It shall have a minimum frequency resolution of greater than or equal to 8 digits. It shall have a maximum error accuracy of plus/minus 1 micro Hz. It shall have a minimum of two sweep modes to include a continuous sweep and a triggered sweep. It shall have the capability of two wide sweep bands to include 1 micro Hz to 500 kHz and 5kHz to 50 MHz. It shall have the capability of external phase and amplitude modulation. It shall have the capability of being operated as a function generator. It shall have the capability of producing sine, square, triangle, ramps, haversine, havertriangle waveshapes. (3) Digitizer Plug-In, MFG AnalogCorp/Data Precision Div., P/N D620. The digitizer shall have a sampling rate of 100 MHz with a resolution of 8 bits. It shall have a bandwidth at 3 dB of 20 MHz. It shall have a sampling period of 10 ns to 300s. It shall have a minimum of three isolated channels. It shall have an input range of plus/minus 1 V or 3 V with capability of plus/minus 0.05 V to plus/minus 20 V when using the compatible Data Precision Model D1000, Dual Preamplifier. It shall be compatible to the Data Precision Model D6000 Waveform Analyzer Mainframe. (4) Universal Counter, MFG Hewlett Packard, P/N 5335A. Minimum frequency range for channel B shall be DC to 100 MHz for DC coupled, and the upper frequency limit for channel A shall be 200 MHZ. Input sensitivity for both channels shall be a minimum of 25 millivolts RMS. Input dynamic range for both channels shall be a minimum of 75 millivolts to 5 volts peak-to-peak for up to 100 MHz. Signal operating range for both channels shall be a minimum of plus/minus 5 volts DC. Manual mode triggering range shall be a minimum of plus/minus 5 V DC. Automatic mode triggering shall be adjustable between the high and low peaks of the input signal. The counter shall be capable of measuring; frequency, period, time interval between channels A and B, rise and fall times, pulse width, duty cycle, ratio of channel A and B, totalize and phase of channel A relative to channel B. Frequency measurement range for channel A shall be a minimum of DC to 200 MHz and channel B, DC to 100 MHz. (5) Selective Level Meter, MFG Hewlett Packard, P/N 3586C. The selective level meter shall be fully HP-IB programmable. It shall have a minimum frequency range of 50 Hz to 32.5MHz. It shall have capability of three input impedences to include 50, 75, and 600 ohms with 10 K ohm bridging. It shall have a minimum signal level accuracy of 0.02 dB with resolution of 0.01 dB. (6) Digital Multimeter, MFG Hewlett Packard, P/N 3456A. The multimeter shall be fully HP-IB programmable and have a program memory which can execute an internal program to control instrument configuration and measurement sequence. It shall be capable of storing up to 350 readings and of reading DC, true RMS AC, and resistance. It shall have a minimum of five DC voltage ranges to include 0.1V, 1.0V, 10.V, 100.0V, and 1000.0V with a 6- 1/2 digit resolution of 100nV on the 0.1V scale. It shall have a minimum of four AC RMS voltage ranges to include 1.0V, 10.0V, 100.0V, and 1000.0V with a 6-1/2 digit resolution of 1 micro V on the 1.0V scale. It shall have a minimum of eight resistance measurement ranges to include 100 ohm, 1 k ohm, 10 k ohm, 100 k ohm, 1 M ohm, 10 M ohm, 100 M ohm, and 1 G ohm with a 6-1/2 digit resolution of 100 micro ohm. (7) Synthesizer/Level Generator, MFG Hewlett Packard, P/N 3336B. The synthesizer/level generator shall be fully HP-IB programmable and have a minimum frequency range of signal outputs of 10 Hz to 20.999,999,999 MHz. It shall have a frequency resolution of 1 micro Hz for frequencies less than 100 kHz. It shall be capable of amplitude and phase modulation. It shall have a wide band sweep capability that is phase continuous over the full frequency range. (8) Waveform Analyzer Mainframe, MFG. Analogic Corp/Data Precision Div., P/N D6000. The analyzer functions shall be fully readable and programmable from RS-232 or IEEE-488 remote bus control. It shall have a 16-bit, 8 MHz internal clock speed. It shall have a real-time clock which logs time to 0.01s and date with a battery backup. It shall have a 9-inch CRT display with screen resolutions of 512 lines horizontal by 1024 lines vertical. It shall have five user selectable display modes to include single-trace full-screen, two-trace half-screen each, four-trace quarter-screen each, two-trace overlaid full-screen and four-trace overlaid full-screen. It shall have capability of two-axis trace expansion and contraction. It shall have compatibility with Data Precision Model D620, Plug-in Digitizer and Model D1000, Dual Preamplifier. The provisions at FAR 52.212-1, Instructions to Offerors-Commercial, and FAR clause 52.212-4, Contract Terms and Conditions-Commercial Items apply to this acquisition. Include a completed copy of the provision at FAR 52.212-3, Offeror Representations and Certifications - Commercial Items, with any quotes submitted in response to this notice. The clause at FAR 52.212-5, Contract Terms and Conditions Required to Implement Statutes or Executive Orders-- Commercial Items applies to this acquisition. As this procurement is being initiated under Other Than Full and Open Competition, contract award will be made to Tucker Electronics Company if they and the Government come to an agreement on all applicable terms and conditions. This includes, but is not limited to, the Government determining the price proposed to be fair and reasonable. All responses are due no later than 4:00 PM on 24 May 1996. Send to: NAVSURFWARCENDIV, Bldg. 64, Bid Room Depository, 300 Highway 361, Crane, IN 47522-5011. Reference the above solicitation number when responding to this notice. The point of contact for additional information is Ms. M. T. Sturgis, Code 1165ZK, 812-854-3730/3735. All responsible sources may submit an offer which shall be considered by this agency (0131)

Loren Data Corp. http://www.ld.com (SYN# 0368 19960513\66-0001.SOL)